![]() |
PLEASE PATRONIZE OUR SPONSORS!
|
![]() |
|
Thread Tools
![]() |
Display Modes
![]() |
#1
|
|||
|
|||
![]()
Bringing old post back to life.
What about 4 different cylinders? How would you do it? Run 2 - 2 spool valves, or a triple & single?
__________________
________________________ Scot |
#2
|
||||
|
||||
![]()
__________________
1- 1864 Dual hyd, cat 0, axle braces 1- 1450 Dual Stick w/ power steering 1- 1200 in pieces 1- 1864 in pieces QA36A Thrower, #1 Tiller w/ extensions, IH windbreaker, IH wheel weights, 44C mower deck, 50C mower deck, CCC 54" Blade, GT46 high vacuum deck, GT54 deck, Cub Tripple Bagger, Custom dozer blade, Custom suitcase weights, 3pt cultivator, lawn sweeper, original R-Bucket |
#3
|
|||
|
|||
![]()
Didnt read through all of it, but what I did read sounds like a 3 spool valve with a diverter solenoid to redirect to a different cylinder...?
__________________
________________________ Scot |
#4
|
|||
|
|||
![]() Quote:
It would do you good to read the whole thread. Maybe you wouldn't have any more questions..... |
#5
|
|||
|
|||
![]()
This is my suggestion....
__________________
[B]Roland Bedell[/B] CC Models: 100, 105, 1450, 782, (2) 784, & 2072 [SIZE="4"][B][COLOR="Red"]Buy:[/COLOR][COLOR="Blue"] Made in the USA[/COLOR][/B] [/SIZE]:American Flag 1: |
#6
|
|||
|
|||
![]()
As long as you don't want to use more than one at once, that would work. But in that set up, the first valve takes priority.
|
#7
|
|||
|
|||
![]() Quote:
Let's see, One hand on the Steering Wheel, and One hand on a valve, probably be OK.
__________________
[B]Roland Bedell[/B] CC Models: 100, 105, 1450, 782, (2) 784, & 2072 [SIZE="4"][B][COLOR="Red"]Buy:[/COLOR][COLOR="Blue"] Made in the USA[/COLOR][/B] [/SIZE]:American Flag 1: |
#8
|
||||
|
||||
![]()
The JD valve I used was a Dukes valve. I found the literature and have included the link here. Hope maybe it helps someone.
http://qccllc.com/sites/all/themes/m...Model-1627.pdf
__________________
Richard 1979 IH Cub Cadet 782 w/CH20, dual hydraulics, power steering and Cat 0 three point |
#9
|
|||
|
|||
![]() Quote:
Plus, if you go by the thought that you can only operate one valve at a time because you have to have one hand on the steering wheel, then you wouldn't be any good at running a loader. You have to tilt the bucket while lifting or you will dump the load. Should be able to rum at least 2 at a time. 3 if they're positioned right. |
#10
|
||||
|
||||
![]()
Ever done That? A tripple spool is tough enough to squeeze into that cowel. Would think that would be next to impossible to do while retaining an authentic look
__________________
1- 1864 Dual hyd, cat 0, axle braces 1- 1450 Dual Stick w/ power steering 1- 1200 in pieces 1- 1864 in pieces QA36A Thrower, #1 Tiller w/ extensions, IH windbreaker, IH wheel weights, 44C mower deck, 50C mower deck, CCC 54" Blade, GT46 high vacuum deck, GT54 deck, Cub Tripple Bagger, Custom dozer blade, Custom suitcase weights, 3pt cultivator, lawn sweeper, original R-Bucket |
![]() |
|
|
Cub Cadet is a premium line of outdoor power equipment, established in 1961 as part of International Harvester. During the 1960s, IH initiated an entirely new line of lawn and garden equipment aimed at the owners rural homes with large yards and private gardens. There were a wide variety of Cub Cadet branded and after-market attachments available; including mowers, blades, snow blowers, front loaders, plows, carts, etc. Cub Cadet advertising at that time harped on their thorough testing by "boys - acknowledged by many as the world's worst destructive force!". Cub Cadets became known for their dependability and rugged construction.
MTD Products, Inc. of Cleveland, Ohio purchased the Cub Cadet brand from International Harvester in 1981. Cub Cadet was held as a wholly owned subsidiary for many years following this acquisition, which allowed them to operate independently. Recently, MTD has taken a more aggressive role and integrated Cub Cadet into its other lines of power equipment.
This website and forum are not affiliated with or sponsored by MTD Products Inc, which owns the CUB CADET trademarks. It is not an official MTD Products Inc, website, and MTD Products Inc, is not responsible for any of its content. The official MTD Products Inc, website can be found at: http://www.mtdproducts.com. The information and opinions expressed on this website are the responsibility of the website's owner and/or it's members, and do not represent the opinions of MTD Products Inc. IH, INTERNATIONAL HARVESTER are registered trademark of CNH America LLC
All material, images, and graphics from this site are the property of www.onlycubcadets.net. Any unauthorized use, reproductions, or duplications are prohibited unless solely expressed in writing.
Cub Cadet, Cub, Cadet, IH, MTD, Parts, Tractors, Tractor, International Harvester, Lawn, Garden, Lawn Mower, Kohler, garden tractor equipment, lawn garden tractors, antique garden tractors, garden tractor, PTO, parts, online, Original, 70, 71, 72, 73, 76, SO76, 80, 81, 86, 100, 102, 104, 105, 106, 107, 108,109, 122, 123, 124, 125, 126, 127, 128, 129, 147, 149, 169, 182, 282, 382, 482, 580, 582, 582 Special, 680, 682, 782, 782D, 784, 800, 805, 882, 982, 984, 986, 1000, 1015, 1100, 1105, 1110, 1200, 1250, 1282, 1450, 1512, 1604, 1605, 1606, 1610, 1615, 1620, 1650, 1710, 1711, 1712, 1806, 1810, 1811, 1812, 1912, 1914.