Only Cub Cadets

PLEASE PATRONIZE OUR SPONSORS!

CC Specialties R. F. Houtz and Sons Jeff in Pa.

P&K Cub Cadet Machtech Direct

Cub Cadet Parts & Service


If you would like to help maintain this site & enhance it, feel free to donate whatever amount you would like to!




Go Back   Only Cub Cadets > Cub Cadets > Implements and Attachments

Notices

Reply
 
Thread Tools Display Modes
  #11  
Old 07-02-2018, 07:10 PM
sorner's Avatar
sorner sorner is offline
Grand Member
 
Join Date: Jan 2017
Location: PA
Posts: 1,324
Default

86” belt routes properly cuts like a champ!
__________________
1872 with 50C deck
1862 with 50C deck
1641 with 48GT deck
364 snow blower
IH Cub Original with deck
GREEN 317 with integral sleeve hitch, front hydraulic
Reply With Quote
  #12  
Old 07-02-2018, 09:27 PM
J-Mech J-Mech is offline
Banned
 
Join Date: Apr 2013
Location: Oblong, Illinois
Posts: 17,594
Default

Belt tensioners, especially spring loaded ones, ALWAYS go on the slack side of the drive belt. In other words, the side of the belt that is not under drive tension. The center pulley is the drive pulley, it is connected to the engine. It spins clockwise facing it from the top. Therefore, the section of the belt off the left side of the center pulley is being "pulled". It pulls on the pulley on the left side of the deck. Then the pulling force continues to the far side of the deck to the right hand pulley. The section of belt that goes between the right hand pulley and the center drive is not under tension. That is where the idler pulley will go. In the pic, the red line representing the belt the OP had installed, the tensioner was on the driven side, or tension side of the belt. Therefore, the torque would simply collapse the spring, and the section of belt between the right pulley and center pulley would go slack, and lose friction as the belt entered the groove on the RH pulley.

Belt routing 101: Spring loaded tensioner ALWAYS goes on the slack section between the last driven pulley and the drive pulley.
Reply With Quote
  #13  
Old 07-03-2018, 06:02 AM
sorner's Avatar
sorner sorner is offline
Grand Member
 
Join Date: Jan 2017
Location: PA
Posts: 1,324
Default

Thanks. From now on I know when I part is called for and what I have taken off doesn’t match up, the PO did something and I need to dig into it and figure out why.
__________________
1872 with 50C deck
1862 with 50C deck
1641 with 48GT deck
364 snow blower
IH Cub Original with deck
GREEN 317 with integral sleeve hitch, front hydraulic
Reply With Quote
  #14  
Old 07-03-2018, 06:33 AM
R Bedell R Bedell is offline
Founding Member
 
Join Date: Mar 2007
Location: Michigan
Posts: 13,693
Default

The "belt route" can be found here at this Link..... Operator's Manual

On the 44/50 decks, it is on Page #10.
__________________
[B]Roland Bedell[/B]

CC Models: 100, 105, 1450, 782, (2) 784, & 2072

[SIZE="4"][B][COLOR="Red"]Buy:[/COLOR][COLOR="Blue"] Made in the USA[/COLOR][/B] [/SIZE]:American Flag 1:
Reply With Quote
Reply


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 05:02 PM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2025, vBulletin Solutions Inc.

Cub Cadet is a premium line of outdoor power equipment, established in 1961 as part of International Harvester. During the 1960s, IH initiated an entirely new line of lawn and garden equipment aimed at the owners rural homes with large yards and private gardens. There were a wide variety of Cub Cadet branded and after-market attachments available; including mowers, blades, snow blowers, front loaders, plows, carts, etc. Cub Cadet advertising at that time harped on their thorough testing by "boys - acknowledged by many as the world's worst destructive force!". Cub Cadets became known for their dependability and rugged construction.

MTD Products, Inc. of Cleveland, Ohio purchased the Cub Cadet brand from International Harvester in 1981. Cub Cadet was held as a wholly owned subsidiary for many years following this acquisition, which allowed them to operate independently. Recently, MTD has taken a more aggressive role and integrated Cub Cadet into its other lines of power equipment.

This website and forum are not affiliated with or sponsored by MTD Products Inc, which owns the CUB CADET trademarks. It is not an official MTD Products Inc, website, and MTD Products Inc, is not responsible for any of its content. The official MTD Products Inc, website can be found at: http://www.mtdproducts.com. The information and opinions expressed on this website are the responsibility of the website's owner and/or it's members, and do not represent the opinions of MTD Products Inc. IH, INTERNATIONAL HARVESTER are registered trademark of CNH America LLC

All material, images, and graphics from this site are the property of www.onlycubcadets.net. Any unauthorized use, reproductions, or duplications are prohibited unless solely expressed in writing.

Cub Cadet, Cub, Cadet, IH, MTD, Parts, Tractors, Tractor, International Harvester, Lawn, Garden, Lawn Mower, Kohler, garden tractor equipment, lawn garden tractors, antique garden tractors, garden tractor, PTO, parts, online, Original, 70, 71, 72, 73, 76, SO76, 80, 81, 86, 100, 102, 104, 105, 106, 107, 108,109, 122, 123, 124, 125, 126, 127, 128, 129, 147, 149, 169, 182, 282, 382, 482, 580, 582, 582 Special, 680, 682, 782, 782D, 784, 800, 805, 882, 982, 984, 986, 1000, 1015, 1100, 1105, 1110, 1200, 1250, 1282, 1450, 1512, 1604, 1605, 1606, 1610, 1615, 1620, 1650, 1710, 1711, 1712, 1806, 1810, 1811, 1812, 1912, 1914.