Only Cub Cadets

PLEASE PATRONIZE OUR SPONSORS!

CC Specialties R. F. Houtz and Sons Jeff in Pa.

P&K Cub Cadet Machtech Direct

Cub Cadet Parts & Service


If you would like to help maintain this site & enhance it, feel free to donate whatever amount you would like to!




Attention Guest, We have turned off the forum to guest. This is due to bots attacking the site. It is still free to register.

-->
Go Back   Only Cub Cadets > Cub Cadets > IH Cub Cadet Tractors (GT)

Notices

Reply
 
Thread Tools Display Modes
  #1  
Old 04-04-2015, 02:18 PM
Alvy's Avatar
Alvy Alvy is offline
Grand Member
 
Join Date: Jul 2012
Location: Winter Haven, FL
Posts: 3,567
Default

You can view the service manual for the original on how to remove. 2 bolts on left side, one bolt on right side, remove clutch actuator shaft, and 2 bolts at flex coupler, drop out drive shaft and clutch as a unit. Drive out spiral pin at input shaft and remove coupler. Put a couple screws in the seal and pull out with vice grips. I would make sure you don't have a lot of play in the input and inspect input shaft for scoring. Both of which will make it leak. Here is a pic of clutch you will be removing. You can take out entire rear with 4 big 3/4 head bolts and disconnect brake linkage too but I think this can be done under tractor with rear in place just as easy.

image.jpg
__________________
(2) Original, 100, 102, 124, 73, 800, #1 and #2 cart, brinly plows, disk, IH184, IH244, 1948 F Cub
Reply With Quote
  #2  
Old 04-07-2015, 10:44 PM
Unconventional Unconventional is offline
New Member
 
Join Date: Apr 2013
Location: Colorado
Posts: 9
Default

Thanks for the walk through. I have got it all torn down and ready for the new seal to go in.
Reply With Quote
  #3  
Old 10-17-2021, 06:12 PM
That_cub_dude1847 That_cub_dude1847 is offline
Member
 
Join Date: Jun 2020
Location: Pennsylvania
Posts: 90
Default

Quote:
Originally Posted by Alvy View Post
You can view the service manual for the original on how to remove. 2 bolts on left side, one bolt on right side, remove clutch actuator shaft, and 2 bolts at flex coupler, drop out drive shaft and clutch as a unit. Drive out spiral pin at input shaft and remove coupler. Put a couple screws in the seal and pull out with vice grips. I would make sure you don't have a lot of play in the input and inspect input shaft for scoring. Both of which will make it leak. Here is a pic of clutch you will be removing. You can take out entire rear with 4 big 3/4 head bolts and disconnect brake linkage too but I think this can be done under tractor with rear in place just as easy.

Attachment 63699
When Installing the seal, should I put any sealant around it?
Reply With Quote
  #4  
Old 10-17-2021, 07:56 PM
darkminion_17's Avatar
darkminion_17 darkminion_17 is offline
Grand Member
 
Join Date: Aug 2010
Location: New Jersey
Posts: 11,265
Default

no sealant is necessary.
__________________
Up to 533 and counting...
I give up updating my profile!
Reply With Quote
Reply


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 10:25 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2025, vBulletin Solutions Inc.

Cub Cadet is a premium line of outdoor power equipment, established in 1961 as part of International Harvester. During the 1960s, IH initiated an entirely new line of lawn and garden equipment aimed at the owners rural homes with large yards and private gardens. There were a wide variety of Cub Cadet branded and after-market attachments available; including mowers, blades, snow blowers, front loaders, plows, carts, etc. Cub Cadet advertising at that time harped on their thorough testing by "boys - acknowledged by many as the world's worst destructive force!". Cub Cadets became known for their dependability and rugged construction.

MTD Products, Inc. of Cleveland, Ohio purchased the Cub Cadet brand from International Harvester in 1981. Cub Cadet was held as a wholly owned subsidiary for many years following this acquisition, which allowed them to operate independently. Recently, MTD has taken a more aggressive role and integrated Cub Cadet into its other lines of power equipment.

This website and forum are not affiliated with or sponsored by MTD Products Inc, which owns the CUB CADET trademarks. It is not an official MTD Products Inc, website, and MTD Products Inc, is not responsible for any of its content. The official MTD Products Inc, website can be found at: http://www.mtdproducts.com. The information and opinions expressed on this website are the responsibility of the website's owner and/or it's members, and do not represent the opinions of MTD Products Inc. IH, INTERNATIONAL HARVESTER are registered trademark of CNH America LLC

All material, images, and graphics from this site are the property of www.onlycubcadets.net. Any unauthorized use, reproductions, or duplications are prohibited unless solely expressed in writing.

Cub Cadet, Cub, Cadet, IH, MTD, Parts, Tractors, Tractor, International Harvester, Lawn, Garden, Lawn Mower, Kohler, garden tractor equipment, lawn garden tractors, antique garden tractors, garden tractor, PTO, parts, online, Original, 70, 71, 72, 73, 76, SO76, 80, 81, 86, 100, 102, 104, 105, 106, 107, 108,109, 122, 123, 124, 125, 126, 127, 128, 129, 147, 149, 169, 182, 282, 382, 482, 580, 582, 582 Special, 680, 682, 782, 782D, 784, 800, 805, 882, 982, 984, 986, 1000, 1015, 1100, 1105, 1110, 1200, 1250, 1282, 1450, 1512, 1604, 1605, 1606, 1610, 1615, 1620, 1650, 1710, 1711, 1712, 1806, 1810, 1811, 1812, 1912, 1914.