![]() |
PLEASE PATRONIZE OUR SPONSORS!
|
![]() |
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
![]()
I've had my 782D for several years now. I change all filters every spring and it's ran great until a couple of weeks ago. It would be running fine, mowing and then sound like it was running out of fuel. I fill it before I use it each week and was certain that there was fuel in the tank so I figured fuel filter..
I bought a new fuel filter and picked up an oil and an air filter while I was at the Kubota dealer, thinking it couldn't hurt. Well I changed the fuel filter, and oil and went to change the air filter and found it was packed with a mouse nest. After installing the new filters, adding oil, and bleeding the air from the fuel lines it fired right up. I ran it for about 3 hours and it ran without missing a beat so it was $55 well spent ![]() Now what I learned is that I'm missing a screen that goes into #2. I have the plastic piece but no screen, I never realized it was missing. I'm probably going to see if I can make one from hardware cloth until I can find a good used one. Anyone know what size the mesh is? I have some 1/4" hardware cloth, it will at least keep the mice out. Also, what holds it in?
__________________
I like to keep em running and work them. 1872 (I call her Vera), 782D, 154 Loboy (w/tiller, 3260 deck, and front blade), 3-1650s, 2-1000s, 149, 147, 106, 1810, Farmall Cub, Haban sickle bar (not mounted), No. 2 trailer and several parts tractors. |
#2
|
|||
|
|||
![]()
I can't help ya with the correct part, but for a very similar thing for a piece of factory equipment we made pre-filters out of stainless steel sink strainers. They're about $4 at the store.
http://www.amazon.com/LDR-501-3340-S...=sink+strainer |
#3
|
|||
|
|||
![]() Quote:
![]() ![]()
__________________
Don B, USAF 1962-1968, Ft. Wayne, IN |
#4
|
||||
|
||||
![]()
I am missing the same screen on my 882. The guy I bought my 882 from had 2 782d's and they both had the a screen. It looked like nothing really held it in. The screen seemed to be cut mabe an 1/8" bigger diamerter than the hole and you push the screen in the hole with only one finger in the center of the screen so it bows the screen and holds it in place. I'm not sure if that's the way it came from the factory but that was the way these two 782d had them.
__________________
Original- Wheel Weights, AG tires, Brinly Sleeve Hitch, #2 Cart 882- 50c Mower Deck 2182- 60c Mower Deck, Rear PTO, Cat 0 3-Point, Brinly 60" rear blade Case 646 FEL Case 446 |
#5
|
||||
|
||||
![]()
One of my diesels has window screen material covering that opening with a hose clamp around the outside to hold everything. Seems to work fine for me and haven't noticed any issues. The main function is to do exactly was happened to you, keep out the mice and other vermin, especially their housing supplies....... The air filter does the filtering.........
![]()
__________________
Josh Diesel Cub Cadets........... |
#6
|
||||
|
||||
![]()
Mine came out of my 782D years ago. I luckily happened to see it on the lawn when I was cleaning the deck. I ended up taking the whole plastic piece off of the tractor and putting a bead of silicone in the recess where the screen was, then putting the screen in the silicone and laying another small bead on top of the screen. I left it on the workbench with the screen facing up and a weight on it over night till the silicone dried. It's been on there since then no problems.
__________________
1989 - Cub Cadet 1772 1987 - Cub Cadet 1572 w/Rear PTO & Cat. 0 38" Lawn Sweeper #196483 42" L42 (Bush Hog) Rotary Cutter # 190349 45" 2-Stage Snowblower # 196364 48" Haban Rotortiller Rear PTO Driven #190356 54" SnowBlade with hydraulic Angle #196376 60" Haban Mowing Deck #196374 |
#7
|
|||
|
|||
![]()
Thanks guys! The silicone idea is a good one, hadn't thought of that. It should hold up fine.
It's always WAR with them mice ![]() My garage is surrounded by tall grass that I only brush hog once or twice a year so that doesn't help with the mice situation. It's also got plenty of spots for them to get in so I'm constantly catching them. I set a trap at each door about every time I'm out there (with peanut butter) and I usually have a mouse in both the next day. There's also 2 or 3 stray cats I see all the time as well as a bunch of hawks so I don't use poison, afraid it might hurt them. Every time I find a nest of mice I chuck them in the pond and watch the fish gobble them up ![]()
__________________
I like to keep em running and work them. 1872 (I call her Vera), 782D, 154 Loboy (w/tiller, 3260 deck, and front blade), 3-1650s, 2-1000s, 149, 147, 106, 1810, Farmall Cub, Haban sickle bar (not mounted), No. 2 trailer and several parts tractors. |
#8
|
|||
|
|||
![]()
Get more spay/neutered stray cats (make sure you fix them) and glue a filter on that thing!
![]() Should work fine. |
#9
|
||||
|
||||
![]() Quote:
|
#10
|
|||
|
|||
![]()
Yep, OUTSIDE cats are great as long as they're not feral, you don't name them, and are fixed. Cats will kill a boat load of stuff. Just give them water on a regular basis and somewhere warm-ish to sleep in the day (any pallet built "buidling" with some straw will work) and you're golden. Feed them just enough that they are still hungry and they'll hunt to beat heck.
Your pet shelter will love you if you say "I'll take anything with all its claws and is fixed that you got. I want barn cats." You'll get 20 in a month, no problem. All of the "problem pets" that they get that pee on/or tear up furniture automatically get killed, so you'll be the first call in that case. Just make sure they're FIXED... and try to run off other cats that aren't yours with a shotgun. Otherwise you'll have 300 inbred cats in about 4 years. |
![]() |
|
|
Cub Cadet is a premium line of outdoor power equipment, established in 1961 as part of International Harvester. During the 1960s, IH initiated an entirely new line of lawn and garden equipment aimed at the owners rural homes with large yards and private gardens. There were a wide variety of Cub Cadet branded and after-market attachments available; including mowers, blades, snow blowers, front loaders, plows, carts, etc. Cub Cadet advertising at that time harped on their thorough testing by "boys - acknowledged by many as the world's worst destructive force!". Cub Cadets became known for their dependability and rugged construction.
MTD Products, Inc. of Cleveland, Ohio purchased the Cub Cadet brand from International Harvester in 1981. Cub Cadet was held as a wholly owned subsidiary for many years following this acquisition, which allowed them to operate independently. Recently, MTD has taken a more aggressive role and integrated Cub Cadet into its other lines of power equipment.
This website and forum are not affiliated with or sponsored by MTD Products Inc, which owns the CUB CADET trademarks. It is not an official MTD Products Inc, website, and MTD Products Inc, is not responsible for any of its content. The official MTD Products Inc, website can be found at: http://www.mtdproducts.com. The information and opinions expressed on this website are the responsibility of the website's owner and/or it's members, and do not represent the opinions of MTD Products Inc. IH, INTERNATIONAL HARVESTER are registered trademark of CNH America LLC
All material, images, and graphics from this site are the property of www.onlycubcadets.net. Any unauthorized use, reproductions, or duplications are prohibited unless solely expressed in writing.
Cub Cadet, Cub, Cadet, IH, MTD, Parts, Tractors, Tractor, International Harvester, Lawn, Garden, Lawn Mower, Kohler, garden tractor equipment, lawn garden tractors, antique garden tractors, garden tractor, PTO, parts, online, Original, 70, 71, 72, 73, 76, SO76, 80, 81, 86, 100, 102, 104, 105, 106, 107, 108,109, 122, 123, 124, 125, 126, 127, 128, 129, 147, 149, 169, 182, 282, 382, 482, 580, 582, 582 Special, 680, 682, 782, 782D, 784, 800, 805, 882, 982, 984, 986, 1000, 1015, 1100, 1105, 1110, 1200, 1250, 1282, 1450, 1512, 1604, 1605, 1606, 1610, 1615, 1620, 1650, 1710, 1711, 1712, 1806, 1810, 1811, 1812, 1912, 1914.