|
PLEASE PATRONIZE OUR SPONSORS!
|
|||||||
 |
|
|
Thread Tools | Display Modes |
|
#1
05-02-2014, 10:28 AM
|
|||
|
|||
105 transmision lever
Thanks for all the help in the past. My next question is, how do you get the transmission direction lever off the console. I've taken the one set screw out, used PB blaster for 4 days and two flat head screw drivers under it to pry up. My next thing was to put a block of wood on top of it and hit the wood with the air chisel while prying up. I don't want to damage the finish or break it. Is the one set screw the only thing holding it on? Is the shaft splined or round? If someone needs pictures I can take them at lunch and post later. Thanks again!
|
|
#3
05-02-2014, 01:58 PM
|
|||
|
|||
|
I have ruined them before getting them off.
Spray PB Blaster in the set screw hole, wiggle it, wait a few days, repeat...
__________________
More IH Cub Cadet Parts RIGHT HERE
|
|
#4
05-02-2014, 06:52 PM
|
||||
|
||||
|
Welcome to the club. I have the same issue with my 149. It will turn on the shaft but I can not get it off. Got the set screw out and it makes no difference. I'll probably end up cutting it off with a die grinder and then fab up something. It has a male spline on the shaft and a female spline on the lever. My guess is the splines on the lever are shot.
__________________
2264 with 54 GT deck 1641 AKA Black Jack with a 402-E Haban Sickle bar mower JD317 dump truck BX2670 with FEL
|
|
#5
05-02-2014, 08:01 PM
|
||||
|
||||
|
Looks like a new tool for Jeff to make.
If you go above the set screw hole and drill another hole above it where the splines are,you can get some PB up in there.
__________________
Up to 530 and counting... I give up updating my profile!
|
|
#7
05-03-2014, 05:03 PM
|
||||
|
||||
|
Well I came up with a way to get the lever off. I drilled a 1/4" hole down through the center till I hit the shaft, then I put a 1/4" socket head bolt in the hole and used a bearing puller to pull it off the shaft. Next I drilled and tapped the lever for a 10-32 screw, then drilled and tapped the shaft for the 10-32 screw ( That's what I had in my bin) Put it back together and Happy Happy Happy.
__________________
2264 with 54 GT deck 1641 AKA Black Jack with a 402-E Haban Sickle bar mower JD317 dump truck BX2670 with FEL
|
|
#8
05-03-2014, 05:57 PM
|
||||
|
||||
|
I eventually rounded out the hex on my 129 and gave it up.
|
|
#10
05-03-2014, 08:50 PM
|
||||
|
||||
|
I got mine off today without damaging anything! I don't have photos, so I'll try to explain. Removed the two bolts holding the control rod support (it's "Z" shaped). Cut a 1-1/2" x 1-1/2" block of wood about 3" long. I C-clamped the control rod support and block of wood to the frame in the same location it normally is bolted. This puts the control lever 1-1/2" above the dash. Room enough to use an 18" pry bar, curved on one end, with a strip of 3/4" thick wood block to protect the dash. I heated the chrome lever with a propane torch just below the set screw hole. Pryed up with the crow bar and it came off. Knowing it has a splined shaft was the key!
|
|
|
|
Cub Cadet is a premium line of outdoor power equipment, established in 1961 as part of International Harvester. During the 1960s, IH initiated an entirely new line of lawn and garden equipment aimed at the owners rural homes with large yards and private gardens. There were a wide variety of Cub Cadet branded and after-market attachments available; including mowers, blades, snow blowers, front loaders, plows, carts, etc. Cub Cadet advertising at that time harped on their thorough testing by "boys - acknowledged by many as the world's worst destructive force!". Cub Cadets became known for their dependability and rugged construction.
MTD Products, Inc. of Cleveland, Ohio purchased the Cub Cadet brand from International Harvester in 1981. Cub Cadet was held as a wholly owned subsidiary for many years following this acquisition, which allowed them to operate independently. Recently, MTD has taken a more aggressive role and integrated Cub Cadet into its other lines of power equipment.
This website and forum are not affiliated with or sponsored by MTD Products Inc, which owns the CUB CADET trademarks. It is not an official MTD Products Inc, website, and MTD Products Inc, is not responsible for any of its content. The official MTD Products Inc, website can be found at: http://www.mtdproducts.com. The information and opinions expressed on this website are the responsibility of the website's owner and/or it's members, and do not represent the opinions of MTD Products Inc. IH, INTERNATIONAL HARVESTER are registered trademark of CNH America LLC
All material, images, and graphics from this site are the property of www.onlycubcadets.net. Any unauthorized use, reproductions, or duplications are prohibited unless solely expressed in writing.
Cub Cadet, Cub, Cadet, IH, MTD, Parts, Tractors, Tractor, International Harvester, Lawn, Garden, Lawn Mower, Kohler, garden tractor equipment, lawn garden tractors, antique garden tractors, garden tractor, PTO, parts, online, Original, 70, 71, 72, 73, 76, SO76, 80, 81, 86, 100, 102, 104, 105, 106, 107, 108,109, 122, 123, 124, 125, 126, 127, 128, 129, 147, 149, 169, 182, 282, 382, 482, 580, 582, 582 Special, 680, 682, 782, 782D, 784, 800, 805, 882, 982, 984, 986, 1000, 1015, 1100, 1105, 1110, 1200, 1250, 1282, 1450, 1512, 1604, 1605, 1606, 1610, 1615, 1620, 1650, 1710, 1711, 1712, 1806, 1810, 1811, 1812, 1912, 1914.
Linear Mode
