|
PLEASE PATRONIZE OUR SPONSORS!
|
|||||||
 |
|
|
Thread Tools | Display Modes |
|
#1
04-14-2010, 05:44 PM
|
||||
|
||||
Internal brake rearend ?
I picked up a rearend and hydro drive from a 1250 today. For the price I couldn't pass it up. But it is an internal brake rear. I am intending on using this on my 1872 project ,so I was planing using the external brakes for the dual brake set up.
1- Can this internal be changed to an external ? 2-Will external axles just fit right in it ? 3- And is there a plug or some thing for where the rod for the internal brake goes ? 4- Or would it just be easier to find an external brake housing ? Any ideas or suggestions would be appreciated. JOE
__________________
Sold everything but one. 1211-snow pusher, cab ,54 inch plow, loaded tires (all 4) Gilson wheel weights, X-trac fronts- soon to have power steering and dual hydraulics 
|
|
#2
04-14-2010, 05:46 PM
|
||||
|
||||
|
All the stuff will fit, but it might be best to just find an external brake housing so you don't have to worry about trying to plug the hole. You'd have to leave the linkage on to hold all of that stuff in there, but it'd probably interfere with the brake rockshaft on the super.
|
|
#3
04-14-2010, 06:02 PM
|
||||
|
||||
|
I haven't taken it apart yet to see about plugging it. I was hoping there was just a pipe plug, or set screw type plug that went in there. The linkage is all behind/beside the hydro drive, so I guess I could just leave it in there. Just trying to eliminate future headaches.
JOE
__________________
Sold everything but one. 1211-snow pusher, cab ,54 inch plow, loaded tires (all 4) Gilson wheel weights, X-trac fronts- soon to have power steering and dual hydraulics
|
|
#5
04-14-2010, 09:29 PM
|
|||
|
|||
 I just work around my problems....but then...well....I am a rebel like that. And it hasn't leaked a lick yet. I'd have to look but I think the brakes are more forward on the Super frames and shouldn't be a problem. Scott
|
|
#6
04-14-2010, 09:54 PM
|
||||
|
||||
|
I didn't realize there was that much room. One thought would be to put the axles from the external rear into the internal rear, and then you could tie the left pedal brake into the internal brake and use the two pedals on the right as independent external brakes.
|
|
#7
04-14-2010, 10:50 PM
|
||||
|
||||
|
Now that is an idea. Use the internal on the left peddle as a park brake so to say. Then just hook the dual brakes up independent of the left peddle.
 JOE
__________________
Sold everything but one. 1211-snow pusher, cab ,54 inch plow, loaded tires (all 4) Gilson wheel weights, X-trac fronts- soon to have power steering and dual hydraulics
|
|
|
|
Cub Cadet is a premium line of outdoor power equipment, established in 1961 as part of International Harvester. During the 1960s, IH initiated an entirely new line of lawn and garden equipment aimed at the owners rural homes with large yards and private gardens. There were a wide variety of Cub Cadet branded and after-market attachments available; including mowers, blades, snow blowers, front loaders, plows, carts, etc. Cub Cadet advertising at that time harped on their thorough testing by "boys - acknowledged by many as the world's worst destructive force!". Cub Cadets became known for their dependability and rugged construction.
MTD Products, Inc. of Cleveland, Ohio purchased the Cub Cadet brand from International Harvester in 1981. Cub Cadet was held as a wholly owned subsidiary for many years following this acquisition, which allowed them to operate independently. Recently, MTD has taken a more aggressive role and integrated Cub Cadet into its other lines of power equipment.
This website and forum are not affiliated with or sponsored by MTD Products Inc, which owns the CUB CADET trademarks. It is not an official MTD Products Inc, website, and MTD Products Inc, is not responsible for any of its content. The official MTD Products Inc, website can be found at: http://www.mtdproducts.com. The information and opinions expressed on this website are the responsibility of the website's owner and/or it's members, and do not represent the opinions of MTD Products Inc. IH, INTERNATIONAL HARVESTER are registered trademark of CNH America LLC
All material, images, and graphics from this site are the property of www.onlycubcadets.net. Any unauthorized use, reproductions, or duplications are prohibited unless solely expressed in writing.
Cub Cadet, Cub, Cadet, IH, MTD, Parts, Tractors, Tractor, International Harvester, Lawn, Garden, Lawn Mower, Kohler, garden tractor equipment, lawn garden tractors, antique garden tractors, garden tractor, PTO, parts, online, Original, 70, 71, 72, 73, 76, SO76, 80, 81, 86, 100, 102, 104, 105, 106, 107, 108,109, 122, 123, 124, 125, 126, 127, 128, 129, 147, 149, 169, 182, 282, 382, 482, 580, 582, 582 Special, 680, 682, 782, 782D, 784, 800, 805, 882, 982, 984, 986, 1000, 1015, 1100, 1105, 1110, 1200, 1250, 1282, 1450, 1512, 1604, 1605, 1606, 1610, 1615, 1620, 1650, 1710, 1711, 1712, 1806, 1810, 1811, 1812, 1912, 1914.
Linear Mode
