|
PLEASE PATRONIZE OUR SPONSORS!
|
#21
02-09-2010, 11:17 AM
|
||||
|
||||
A local guy restored a 782 with rattle can paint. You would never know, and I even asked him, as it shines better than the paint on Dad's Cuda. He said metal prep before the spray, and proper wet sanding after the spray made it all work out.
I am giong to pain the bad spots on my 86 Dodge this way until I can afford a real paint job, It was very sharp. Nice job. 
|
|
#22
02-09-2010, 11:20 AM
|
||||
|
||||
thanks IAfarmer,yeah usually wet sanding after you rattle can really works but so far on this project i haven't had to wet sand,it is going good so far,only if i can get the rear fender to turn out ok...lol....awful big part for rattle can to look good
|
|
#23
02-16-2010, 07:46 PM
|
||||
|
||||
|
got to do a little bit more this week...enjoy the pics....
|
|
#24
02-16-2010, 07:52 PM
|
||||
|
||||
|
and some more
|
|
#25
02-16-2010, 08:06 PM
|
||||
|
||||
|
Looking GREAT Diesel... I was hoping to do that to my 1200 next year,but I can't breathe the vapors from paints due to working in quarries and breathing silica dust. I get terribly sick when I inhale any amount.I have to even watch when I spray paint with cans. Even using a respirator wont totally help. Maybe I should drop my 1200 off at your place for an even trade...lol
__________________
Pat Harmon Loganton,Pa 128 Cub Cadet 1200 Cub cadet (Red) LT 1042 Cub Cadet 1200 Cub Cadet 165 Hydro John Deere 1941 John Deere H 1950 David Bradley 5756 1952 David Bradley 57561 Super Power
|
|
#27
02-17-2010, 12:19 AM
|
|||
|
|||
|
That looks great!! One would never know that was a rattle can job. By the way I was able to get the spirol pins out with the proper set of roll pin punches from Sears. They came out like butter. You are much farther along than me on my 149 restore. Mine is completely apart waiting to start the stripping process. Over her I just need a little time and motivation.
Keep up the good work!! Mark
|
|
#28
02-17-2010, 07:17 AM
|
||||
|
||||
|
Thanks bignastygs,ACecil and gerks,bignasty yours looks good....but we can freshen it up for ya...lol.....gerks...glad those roll pin punches worked out for ya,thanks guys for all the compliments...hey gerks...get us some pics sometime
|
|
#29
02-17-2010, 10:11 AM
|
||||
|
||||
|
It won't be long before I can start the paint on my 1650. What brand and colors of "rattle-can" primer and paint did you use? Did you actually strip the trans/diff and front axle, or just clean and paint? Sure looks nice!
__________________
Tony Stafford, VA 1650, 682...
|
|
#30
02-17-2010, 10:21 AM
|
||||
|
||||
|
thenrie,the primer is rustoleum grey,the paint is from tractor supply...number on the can is 5339-25 for the yellow and 5339-15 for the white...yeah i did strip almost all the parts with a sandblast gun or a angle die grinder with those 3m brand buffing pads...thats what we use at work to clean gasket surfaces since all i do is build diesels
|
 |
|
|
Cub Cadet is a premium line of outdoor power equipment, established in 1961 as part of International Harvester. During the 1960s, IH initiated an entirely new line of lawn and garden equipment aimed at the owners rural homes with large yards and private gardens. There were a wide variety of Cub Cadet branded and after-market attachments available; including mowers, blades, snow blowers, front loaders, plows, carts, etc. Cub Cadet advertising at that time harped on their thorough testing by "boys - acknowledged by many as the world's worst destructive force!". Cub Cadets became known for their dependability and rugged construction.
MTD Products, Inc. of Cleveland, Ohio purchased the Cub Cadet brand from International Harvester in 1981. Cub Cadet was held as a wholly owned subsidiary for many years following this acquisition, which allowed them to operate independently. Recently, MTD has taken a more aggressive role and integrated Cub Cadet into its other lines of power equipment.
This website and forum are not affiliated with or sponsored by MTD Products Inc, which owns the CUB CADET trademarks. It is not an official MTD Products Inc, website, and MTD Products Inc, is not responsible for any of its content. The official MTD Products Inc, website can be found at: http://www.mtdproducts.com. The information and opinions expressed on this website are the responsibility of the website's owner and/or it's members, and do not represent the opinions of MTD Products Inc. IH, INTERNATIONAL HARVESTER are registered trademark of CNH America LLC
All material, images, and graphics from this site are the property of www.onlycubcadets.net. Any unauthorized use, reproductions, or duplications are prohibited unless solely expressed in writing.
Cub Cadet, Cub, Cadet, IH, MTD, Parts, Tractors, Tractor, International Harvester, Lawn, Garden, Lawn Mower, Kohler, garden tractor equipment, lawn garden tractors, antique garden tractors, garden tractor, PTO, parts, online, Original, 70, 71, 72, 73, 76, SO76, 80, 81, 86, 100, 102, 104, 105, 106, 107, 108,109, 122, 123, 124, 125, 126, 127, 128, 129, 147, 149, 169, 182, 282, 382, 482, 580, 582, 582 Special, 680, 682, 782, 782D, 784, 800, 805, 882, 982, 984, 986, 1000, 1015, 1100, 1105, 1110, 1200, 1250, 1282, 1450, 1512, 1604, 1605, 1606, 1610, 1615, 1620, 1650, 1710, 1711, 1712, 1806, 1810, 1811, 1812, 1912, 1914.
Linear Mode
