|
PLEASE PATRONIZE OUR SPONSORS!
|
|||||||
 |
|
|
Thread Tools
|
Display Modes
|
|
|
|
#1
05-05-2011, 06:30 AM
|
|||
|
|||
122 Clutch Reassembly
I have looked at the parts diagram for the clutch assembly and see no mention of a washer/spacer between the clutch loading spring and the clutch throwout bearing. Is the end of the loading spring supposed to make direct contact with the face (large end) of the throwout bearing? Is there supposed to be a washer/spacer between the throwout bearing (small end) and the teaser spring?
Thanks GEL 
|
|
#2
05-05-2011, 08:58 AM
|
||||
|
||||
|
Hey Gel, I just replaced the clutch in my 108 WF, which is similar to your clutch. From the transmission end, it is assembled with a coiled pin, then a washer, then the loading spring, then another washer, then coiled pin, then throwout bearing, the teaser spring comes next, then another coiled pin. So the throwout bearing makes contact with the coiled pin, and then the teaser spring at the other end. No washer or spacer. Your parts list doesn't show the washers, but it will list them under the loading spring. The Service Manual will have instructions for dissassembly and reassembly, and diagrams. I made the mistake of using my parts list diagram to assemble my clutch, and i put my spacer spring on backwards and had to take it apart again. I recommend using the service manual. Hope that helps.
|
|
#4
05-05-2011, 03:28 PM
|
|||
|
|||
|
Quote:
|
|
#5
05-05-2011, 09:54 PM
|
||||
|
||||
|
Duke- Thats a brian miller trick. Only place I have heard of it, but I don't know anyone that has tried it, so don't know if it works or why do it.
|
|
#6
05-05-2011, 10:52 PM
|
|||
|
|||
|
Quote:
|
|
|
|
Cub Cadet is a premium line of outdoor power equipment, established in 1961 as part of International Harvester. During the 1960s, IH initiated an entirely new line of lawn and garden equipment aimed at the owners rural homes with large yards and private gardens. There were a wide variety of Cub Cadet branded and after-market attachments available; including mowers, blades, snow blowers, front loaders, plows, carts, etc. Cub Cadet advertising at that time harped on their thorough testing by "boys - acknowledged by many as the world's worst destructive force!". Cub Cadets became known for their dependability and rugged construction.
MTD Products, Inc. of Cleveland, Ohio purchased the Cub Cadet brand from International Harvester in 1981. Cub Cadet was held as a wholly owned subsidiary for many years following this acquisition, which allowed them to operate independently. Recently, MTD has taken a more aggressive role and integrated Cub Cadet into its other lines of power equipment.
This website and forum are not affiliated with or sponsored by MTD Products Inc, which owns the CUB CADET trademarks. It is not an official MTD Products Inc, website, and MTD Products Inc, is not responsible for any of its content. The official MTD Products Inc, website can be found at: http://www.mtdproducts.com. The information and opinions expressed on this website are the responsibility of the website's owner and/or it's members, and do not represent the opinions of MTD Products Inc. IH, INTERNATIONAL HARVESTER are registered trademark of CNH America LLC
All material, images, and graphics from this site are the property of www.onlycubcadets.net. Any unauthorized use, reproductions, or duplications are prohibited unless solely expressed in writing.
Cub Cadet, Cub, Cadet, IH, MTD, Parts, Tractors, Tractor, International Harvester, Lawn, Garden, Lawn Mower, Kohler, garden tractor equipment, lawn garden tractors, antique garden tractors, garden tractor, PTO, parts, online, Original, 70, 71, 72, 73, 76, SO76, 80, 81, 86, 100, 102, 104, 105, 106, 107, 108,109, 122, 123, 124, 125, 126, 127, 128, 129, 147, 149, 169, 182, 282, 382, 482, 580, 582, 582 Special, 680, 682, 782, 782D, 784, 800, 805, 882, 982, 984, 986, 1000, 1015, 1100, 1105, 1110, 1200, 1250, 1282, 1450, 1512, 1604, 1605, 1606, 1610, 1615, 1620, 1650, 1710, 1711, 1712, 1806, 1810, 1811, 1812, 1912, 1914.
Hybrid Mode
