Only Cub Cadets

Only Cub Cadets (https://www.onlycubcadets.net/forum/index.php)
-   IH Cub Cadet Tractors (GT) (https://www.onlycubcadets.net/forum/forumdisplay.php?f=9)
-   -   Forgive me if this has been asked before, but... (https://www.onlycubcadets.net/forum/showthread.php?t=21670)

drglinski 12-16-2012 08:01 PM

Forgive me if this has been asked before, but...
 
I've got a question about the hydro on my 147. When going from forward to reverse I can notice a slight thump and I have visually seen the pump moving forward and reverse respectively. Is this due to the pump being loose, and if so, how does one go about tightening it?

Thanks

Sam Mac 12-16-2012 08:14 PM

Quote:

Originally Posted by drglinski (Post 164925)
I've got a question about the hydro on my 147. When going from forward to reverse I can notice a slight thump and I have visually seen the pump moving forward and reverse respectively. Is this due to the pump being loose, and if so, how does one go about tightening it?

Thanks

You better take a look at the bolts that hold the rear in the frame. Even the cast iron rears get loose.:bigthink:

drglinski 12-16-2012 08:38 PM

never thought of that... I thought it might be the cap screws that hold the pump to the rear end...

Would the bolts that hold the rear in the frame be those that are needed to be removed when the tractor is involved in a split? (I've got the service manual and I think I know which ones you are referring to)

thanks

darkminion_17 12-16-2012 10:00 PM

Those are the ones, also there is a bracket on each side that attaches the the tranny and the frame.

Methos 12-17-2012 09:09 AM

I had them get loose on the 1650.:bash2:

drglinski 12-17-2012 12:45 PM

I looked at my (cubs) rear end today; three of the 6 cap screws were loose. The one on the front of the rear end (the one that is centered between the 3 that are needed for a split) were the worst. The one on the left side (looking forward) was so loose I could take it out with fingers.

Never would have thought to look there. I figured I had bigger fish to fry. She works MUCH better now, very smooth.

I appreciate the tips on where to look. I'm thankful for this forum and the people on it. Thanks a lot!

Methos 12-17-2012 12:46 PM

Quote:

Originally Posted by drglinski (Post 165047)
I looked at my (cubs) rear end today; three of the 6 cap screws were loose. The one on the front of the rear end (the one that is centered between the 3 that are needed for a split) were the worst. The one on the left side (looking forward) was so loose I could take it out with fingers.

Never would have thought to look there. I figured I had bigger fish to fry. She works MUCH better now, very smooth.

I appreciate the tips on where to look. I'm thankful for this forum and the people on it. Thanks a lot!

I'm glad it was a easy fix for ya!

ACecil 12-17-2012 01:10 PM

Glad to hear you fixed it! :beerchug:

teejk 12-17-2012 01:53 PM

Quote:

Originally Posted by Methos (Post 165016)
I had them get loose on the 1650.:bash2:

I've got mine split at the moment on a 1250 waiting for parts...2 of the 6 bolts were "gone" (one on the right side pumpkin, one on the left side L bracket)...probably has been the case since before I bought it but I never noticed. maybe explains why the donuts are shot and the cooling fan has been nubs since I've owned it (will finally be replaced now that I understand things).

Should some type of "locktight" be used on the rebuild? And as long as I'm on the subject, why does that stuff cost so much?

cubfixer 12-17-2012 02:59 PM

Quote:

Originally Posted by teejk (Post 165060)
I've got mine split at the moment on a 1250 waiting for parts...2 of the 6 bolts were "gone" (one on the right side pumpkin, one on the left side L bracket)...probably has been the case since before I bought it but I never noticed. maybe explains why the donuts are shot and the cooling fan has been nubs since I've owned it (will finally be replaced now that I understand things).

Should some type of "locktight" be used on the rebuild? And as long as I'm on the subject, why does that stuff cost so much?

Probably since there are not too many of the cub cadets left (except at Sam's and Allen's houses)! :biggrin2:


All times are GMT -4. The time now is 12:23 PM.

Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2026, vBulletin Solutions Inc.