Only Cub Cadets

PLEASE PATRONIZE OUR SPONSORS!

CC Speciaalties R. F. Houtz and Sons

Patton Acres IH Cub Cadet Parts

Cub Cadet Parts & Service


If you would like to help maintain this site & enhance it, feel free to donate whatever amount you would like to!




Attention Folks we have a new owner!
Greg Rozar AKA- CubDieselFan


Go Back   Only Cub Cadets > Cub Cadets > Home Made

Notices

Reply
 
Thread Tools Display Modes
  #11  
Old 08-29-2017, 08:51 PM
Workinprogress Workinprogress is offline
Senior Member
 
Join Date: Sep 2013
Location: Vermont
Posts: 172
Default

Thanks!

I completely agree the 120 volt welder with flux core is not the best tool for this job.

With that said, I have been using the same hitch design, done using the same welder on my 1512 for a number years. It has not broken yet. Over the years using this welder I have made multiple items including a 25 ton log splitter, heavy duty trailer for my cub, repaired 1.5 ton dump trailer. Using a process of material beveling and multiple pass welding I have very few welds break.

A more powerful welder is on my wish list but for now I have to make due with what I have.
__________________
1512 with CADloader 507, CADdigger 508 and 3 pt
1711 with KT17
782 with KT17 and 3 pt
104
Reply With Quote
  #12  
Old 08-29-2017, 09:01 PM
J-Mech J-Mech is offline
Banned
 
Join Date: Apr 2013
Location: Oblong, Illinois
Posts: 17,594
Default

You can pick up a used Lincoln "tombstone" or "buzz-box" AC arc welder for $100, sometimes less. That would be far better than a 120v flux core machine.

I wouldn't trust a 3pt welded with flux core wire.... but it's your machine. Just out of curiosity, what exactly do you use the 3pt for? Just a York rake?
Reply With Quote
  #13  
Old 08-29-2017, 09:17 PM
Workinprogress Workinprogress is offline
Senior Member
 
Join Date: Sep 2013
Location: Vermont
Posts: 172
Default

The 220 volt welder was on hold until I had the electrical upgraded at the house. This just happened 2 years ago so first step in the right direction!

Right now I use the 3 pt hitch for:
1. York rake (4ft)
2. Small grader blade
3. Carry all.
4. Pallet forks to move empty plastic water storage tanks for maple sap.
5. Log hauler to drag firewood.
6. Trailer hitch but only once and awhile. Like my fixed hitch better.
7. Recently subsoil ripper and moldboard plow (not used much).
__________________
1512 with CADloader 507, CADdigger 508 and 3 pt
1711 with KT17
782 with KT17 and 3 pt
104
Reply With Quote
  #14  
Old 08-29-2017, 10:22 PM
MI Cub MI Cub is offline
New Member
 
Join Date: Apr 2017
Location: Michigan
Posts: 18
Default

Quote:
Originally Posted by Workinprogress View Post
Thanks!

I completely agree the 120 volt welder with flux core is not the best tool for this job.

With that said, I have been using the same hitch design, done using the same welder on my 1512 for a number years. It has not broken yet. Over the years using this welder I have made multiple items including a 25 ton log splitter, heavy duty trailer for my cub, repaired 1.5 ton dump trailer. Using a process of material beveling and multiple pass welding I have very few welds break.

A more powerful welder is on my wish list but for now I have to make due with what I have.
The key factor on your previous welds holding is the beveling and multi pass welding. That little flux core machine will weld the crack of dawn, provided you make enough passes! But in all reality, you can weld anything with your machine that I could do with a 400amp mig machine, it will just take longer. Provided it is properly set up!

But yes, as Jmech stated, the tombstones are pretty reasonable to pick up. I just got one from a guy at work for a crispy $100. Then I was lucky enough to be in the right place at the right time, a friend was cleaning out some garage space and needed a place to keep a weldpack 180 mig. I happily gave it a temporary home next to my weld bench, adding that he could come visit whenever he wanted.

Keep up the good work!
__________________
Matt

1650, 44A deck, front blade, QA42A snow thrower, 1A tiller, 10" brinly plow, brinly cultivator, home made rear bucket, home made sleeve hitch.
Reply With Quote
  #15  
Old 08-30-2017, 08:23 PM
Workinprogress Workinprogress is offline
Senior Member
 
Join Date: Sep 2013
Location: Vermont
Posts: 172
Default

Lift link shafts almost finished. Bending the 1/2 thick flat stock is tough. What I did was make a shallow cut with the band saw. Then bent from the other side of the flat stock (i.e. hit it with big hammer). This opened the cut slightly. I then beveled the edges of cut with a grinder and filled the bevel with the welder. This seemed to allow good control of the bend location without actually having a press.

IMG_5081.jpg


IMG_5082.jpg
__________________
1512 with CADloader 507, CADdigger 508 and 3 pt
1711 with KT17
782 with KT17 and 3 pt
104
Reply With Quote
  #16  
Old 09-04-2017, 07:53 PM
Workinprogress Workinprogress is offline
Senior Member
 
Join Date: Sep 2013
Location: Vermont
Posts: 172
Default

No updates on the hitch but did pick up a Lincoln tombstone for $75. Guy didn't even have outlet to show it worked. He is a friend of a friend and he agreed to give me my money back if it didn't work. Rigged up a temporary electrical outlet in the Garage to test and the unit worked fine. Will finish installing electrical early next week and back to work on the hitches!

List to do:
- Weld inner arms on rock-shaft
- Drill hole in hitch side for installing pin to rock-shaft
- Drill holes for rear hydraulic quick connectors.
- smooth all edges, clean and paint
- build lift arms
- build adjustable links for lift arm.
__________________
1512 with CADloader 507, CADdigger 508 and 3 pt
1711 with KT17
782 with KT17 and 3 pt
104
Reply With Quote
  #17  
Old 09-06-2017, 12:00 PM
MI Cub MI Cub is offline
New Member
 
Join Date: Apr 2017
Location: Michigan
Posts: 18
Default

Nice score! It should serve you well.
__________________
Matt

1650, 44A deck, front blade, QA42A snow thrower, 1A tiller, 10" brinly plow, brinly cultivator, home made rear bucket, home made sleeve hitch.
Reply With Quote
  #18  
Old 09-06-2017, 02:27 PM
scarps68's Avatar
scarps68 scarps68 is offline
Member
 
Join Date: Jun 2015
Location: CT
Posts: 59
Default

I bought a Tombstone for $50 because it "didn't work." I can email you the guide I used to clean and lube the switch contacts. Wouldn't you know I now have a welder that works perfectly.
__________________
Don

882D
50" Deck Mower
54" Snow Dozer Blade
Agri-Fab Lawn Sweep
Reply With Quote
  #19  
Old 09-10-2017, 11:27 PM
Rescue11's Avatar
Rescue11 Rescue11 is offline
Grand Member
 
Join Date: Apr 2011
Location: Nebraska
Posts: 1,490
Default

All this talk about tombstone is making me hungry. Hows the build coming a long?
__________________
1- 1864 Dual hyd, cat 0, axle braces
1- 1450 Dual Stick w/ power steering
1- 1200 in pieces
1- 1864 in pieces
QA36A Thrower, #1 Tiller w/ extensions, IH windbreaker, IH wheel weights, 44C mower deck, 50C mower deck, CCC 54" Blade, GT46 high vacuum deck, GT54 deck, Cub Tripple Bagger, Custom dozer blade, Custom suitcase weights, 3pt cultivator, lawn sweeper, original R-Bucket
Reply With Quote
  #20  
Old 09-11-2017, 07:45 PM
Workinprogress Workinprogress is offline
Senior Member
 
Join Date: Sep 2013
Location: Vermont
Posts: 172
Default

Sorry progress slowed. Spent a couple nights practicing stick welding. Was able to get one hitch welded. Then wife started me on another project.

Last year she copied a painting on plywood with exterior paint. We hung it on the side of the garage.

This year she did three more. Since it was time to replace clap boards i spent the past weekend removing clap boards and putting up paintings.

Now I am on new clap board duty before cub time!

IMG_5089.jpg
__________________
1512 with CADloader 507, CADdigger 508 and 3 pt
1711 with KT17
782 with KT17 and 3 pt
104
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 03:28 PM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.

Cub Cadet is a premium line of outdoor power equipment, established in 1961 as part of International Harvester. During the 1960s, IH initiated an entirely new line of lawn and garden equipment aimed at the owners rural homes with large yards and private gardens. There were a wide variety of Cub Cadet branded and after-market attachments available; including mowers, blades, snow blowers, front loaders, plows, carts, etc. Cub Cadet advertising at that time harped on their thorough testing by "boys - acknowledged by many as the world's worst destructive force!". Cub Cadets became known for their dependability and rugged construction.

MTD Products, Inc. of Cleveland, Ohio purchased the Cub Cadet brand from International Harvester in 1981. Cub Cadet was held as a wholly owned subsidiary for many years following this acquisition, which allowed them to operate independently. Recently, MTD has taken a more aggressive role and integrated Cub Cadet into its other lines of power equipment.

This website and forum are not affiliated with or sponsored by MTD Products Inc, which owns the CUB CADET trademarks. It is not an official MTD Products Inc, website, and MTD Products Inc, is not responsible for any of its content. The official MTD Products Inc, website can be found at: http://www.mtdproducts.com. The information and opinions expressed on this website are the responsibility of the website's owner and/or it's members, and do not represent the opinions of MTD Products Inc. IH, INTERNATIONAL HARVESTER are registered trademark of CNH America LLC

All material, images, and graphics from this site are the property of www.onlycubcadets.net. Any unauthorized use, reproductions, or duplications are prohibited unless solely expressed in writing.

Cub Cadet, Cub, Cadet, IH, MTD, Parts, Tractors, Tractor, International Harvester, Lawn, Garden, Lawn Mower, Kohler, garden tractor equipment, lawn garden tractors, antique garden tractors, garden tractor, PTO, parts, online, Original, 70, 71, 72, 73, 76, SO76, 80, 81, 86, 100, 102, 104, 105, 106, 107, 108,109, 122, 123, 124, 125, 126, 127, 128, 129, 147, 149, 169, 182, 282, 382, 482, 580, 582, 582 Special, 680, 682, 782, 782D, 784, 800, 805, 882, 982, 984, 986, 1000, 1015, 1100, 1105, 1110, 1200, 1250, 1282, 1450, 1512, 1604, 1605, 1606, 1610, 1615, 1620, 1650, 1710, 1711, 1712, 1806, 1810, 1811, 1812, 1912, 1914.