Only Cub Cadets

PLEASE PATRONIZE OUR SPONSORS!

CC Speciaalties R. F. Houtz and Sons

Patton Acres IH Cub Cadet Parts

Cub Cadet Parts & Service


If you would like to help maintain this site & enhance it, feel free to donate whatever amount you would like to!




Attention Folks we have a new owner!
Greg Rozar AKA- CubDieselFan


Go Back   Only Cub Cadets > Cub Cadets > Cub Cadet Engines > Kohler Engines

Notices

Reply
 
Thread Tools Display Modes
  #1  
Old 09-10-2018, 01:20 PM
gscott gscott is offline
New Member
 
Join Date: Aug 2017
Location: Virginia
Posts: 27
Default Brain Storming Oil Cooler

I am not an engineer or expert. I was brainstorming on putting an oil cooler on a k-series Kohler.
Looking for pros and cons...
Could I use a mechanical fuel pump to pump oil through an oil cooler?
Perhaps by placing an NPT fitting in the sump of an oil pan, route it to the "fuel" pump, then back out to an oil cooler, then from the oil cooler to an NPT fitting on the block?
One major question...is the pump strong enough for oil?

Again, just brain storming......
Reply With Quote
  #2  
Old 09-10-2018, 01:44 PM
J-Mech J-Mech is offline
Banned
 
Join Date: Apr 2013
Location: Oblong, Illinois
Posts: 17,594
Default

Unnecessary.
Not likely the fuel pump will pump oil anyway.
Nothing to gain.
Too much involved for no gain.
Reply With Quote
  #3  
Old 09-10-2018, 01:52 PM
cooperino's Avatar
cooperino cooperino is offline
Grand Member
 
Join Date: Dec 2015
Location: New York
Posts: 3,065
Default

Quote:
Originally Posted by gscott View Post
I am not an engineer or expert. I was brainstorming on putting an oil cooler on a k-series Kohler.
Looking for pros and cons...
Could I use a mechanical fuel pump to pump oil through an oil cooler?
Perhaps by placing an NPT fitting in the sump of an oil pan, route it to the "fuel" pump, then back out to an oil cooler, then from the oil cooler to an NPT fitting on the block?
One major question...is the pump strong enough for oil?

Again, just brain storming......
Is your K series running hot??
__________________
Cooperino 100, 104,125, 126, 2x129's, 804, 1211, 1641
Reply With Quote
  #4  
Old 09-10-2018, 01:55 PM
Merk Merk is offline
Grand Member
 
Join Date: Mar 2009
Location: Ohio
Posts: 2,180
Default

Why would you want to do this?

Run an 30 weight dino oil in it and it shouldn't have any problems. I use Kohler oil in all my K-series engines.

There is something wrong-not set right if the engine is running hot.
__________________
Project Uncle Dick
Cub Cadet 70
http://www.onlycubcadets.net/forum/s...ght=Uncle+Dick
Reply With Quote
  #5  
Old 09-12-2018, 01:06 AM
gscott gscott is offline
New Member
 
Join Date: Aug 2017
Location: Virginia
Posts: 27
Default Thanks for the replies

I appreciate the feedback guys. No...engine running well. was just brainstorming. I think the best response was a lot of work with no gain.
Thanks again.
Reply With Quote
  #6  
Old 09-12-2018, 02:05 PM
olds45512's Avatar
olds45512 olds45512 is offline
Grand Member
 
Join Date: May 2014
Location: Indiana, PA
Posts: 8,290
Default

If you're gonna go through all that trouble you better add a filter.
__________________
Tim
Pap's 100
Restored 108
1211 Dual Stick
1050
Pap's 100 restoration thread - http://onlycubcadets.net/forum/showthread.php?t=47965
Reply With Quote
  #7  
Old 09-12-2018, 02:14 PM
J-Mech J-Mech is offline
Banned
 
Join Date: Apr 2013
Location: Oblong, Illinois
Posts: 17,594
Default

Quote:
Originally Posted by olds45512 View Post
If you're gonna go through all that trouble you better add a filter.
A fuel pump wouldn't make enough pressure to push oil through a filter. I really don't think a fuel pump would pump 30wt oil at all..... but I never tried it. Even if it did, it's only a few cc's per stroke. 2, maybe 3 at most. It would pump so slow, you wouldn't need a cooler. It would cool just going through a steel tube 12"-18" long.

Big waste of time anyway.
Reply With Quote
  #8  
Old 09-12-2018, 02:47 PM
olds45512's Avatar
olds45512 olds45512 is offline
Grand Member
 
Join Date: May 2014
Location: Indiana, PA
Posts: 8,290
Default

Quote:
Originally Posted by J-Mech View Post
A fuel pump wouldn't make enough pressure to push oil through a filter. I really don't think a fuel pump would pump 30wt oil at all..... but I never tried it. Even if it did, it's only a few cc's per stroke. 2, maybe 3 at most. It would pump so slow, you wouldn't need a cooler. It would cool just going through a steel tube 12"-18" long.

Big waste of time anyway.
It was a joke. You need to relax a bit.
__________________
Tim
Pap's 100
Restored 108
1211 Dual Stick
1050
Pap's 100 restoration thread - http://onlycubcadets.net/forum/showthread.php?t=47965
Reply With Quote
  #9  
Old 09-12-2018, 03:09 PM
J-Mech J-Mech is offline
Banned
 
Join Date: Apr 2013
Location: Oblong, Illinois
Posts: 17,594
Default

Quote:
Originally Posted by olds45512 View Post
It was a joke. You need to relax a bit.
Ok.... I get it....... But I didn't want anyone taking it seriously.
Reply With Quote
  #10  
Old 09-12-2018, 03:16 PM
cooperino's Avatar
cooperino cooperino is offline
Grand Member
 
Join Date: Dec 2015
Location: New York
Posts: 3,065
Default

Quote:
Originally Posted by J-Mech View Post
A fuel pump wouldn't make enough pressure to push oil through a filter. I really don't think a fuel pump would pump 30wt oil at all..... but I never tried it. Even if it did, it's only a few cc's per stroke. 2, maybe 3 at most. It would pump so slow, you wouldn't need a cooler. It would cool just going through a steel tube 12"-18" long.

Big waste of time anyway.
It won't.. We tried using a electric fuel 12 psi pump with 5/16 inlet and outlet to transfer some oil. It started to pull it but as soon as it hit the pump it stopped.
__________________
Cooperino 100, 104,125, 126, 2x129's, 804, 1211, 1641
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 06:10 PM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.

Cub Cadet is a premium line of outdoor power equipment, established in 1961 as part of International Harvester. During the 1960s, IH initiated an entirely new line of lawn and garden equipment aimed at the owners rural homes with large yards and private gardens. There were a wide variety of Cub Cadet branded and after-market attachments available; including mowers, blades, snow blowers, front loaders, plows, carts, etc. Cub Cadet advertising at that time harped on their thorough testing by "boys - acknowledged by many as the world's worst destructive force!". Cub Cadets became known for their dependability and rugged construction.

MTD Products, Inc. of Cleveland, Ohio purchased the Cub Cadet brand from International Harvester in 1981. Cub Cadet was held as a wholly owned subsidiary for many years following this acquisition, which allowed them to operate independently. Recently, MTD has taken a more aggressive role and integrated Cub Cadet into its other lines of power equipment.

This website and forum are not affiliated with or sponsored by MTD Products Inc, which owns the CUB CADET trademarks. It is not an official MTD Products Inc, website, and MTD Products Inc, is not responsible for any of its content. The official MTD Products Inc, website can be found at: http://www.mtdproducts.com. The information and opinions expressed on this website are the responsibility of the website's owner and/or it's members, and do not represent the opinions of MTD Products Inc. IH, INTERNATIONAL HARVESTER are registered trademark of CNH America LLC

All material, images, and graphics from this site are the property of www.onlycubcadets.net. Any unauthorized use, reproductions, or duplications are prohibited unless solely expressed in writing.

Cub Cadet, Cub, Cadet, IH, MTD, Parts, Tractors, Tractor, International Harvester, Lawn, Garden, Lawn Mower, Kohler, garden tractor equipment, lawn garden tractors, antique garden tractors, garden tractor, PTO, parts, online, Original, 70, 71, 72, 73, 76, SO76, 80, 81, 86, 100, 102, 104, 105, 106, 107, 108,109, 122, 123, 124, 125, 126, 127, 128, 129, 147, 149, 169, 182, 282, 382, 482, 580, 582, 582 Special, 680, 682, 782, 782D, 784, 800, 805, 882, 982, 984, 986, 1000, 1015, 1100, 1105, 1110, 1200, 1250, 1282, 1450, 1512, 1604, 1605, 1606, 1610, 1615, 1620, 1650, 1710, 1711, 1712, 1806, 1810, 1811, 1812, 1912, 1914.