PLEASE PATRONIZE OUR SPONSORS!
#11
|
||||
|
||||
Quote:
1863/4 shaft doesn't seem like it'd be easy to find. Just under $200 new.
__________________
RUN IN THE RED 782 w/50c deck (red); 782 dual stick, 44c deck (y/w); 1050 w/38c deck; 1864 w/54" GT deck; 1872 project Cub Cadet Pro Z 560 L 42" power angle snowblade, #2 tiller, 2-QA42a snowthrowers, 450 thrower, #2 cart; 54" Haban blade; Brinly box blade, 48" dethatcher, moldboard plow; Agri-Fab sweeper 1200, 1863, 1864 parts machines |
#12
|
|||
|
|||
I'd looked through some of the popular retail sites for 1864 parts; they seem hard to find.
A few images up from the hub, it looks like Jeff sells custom-made driveshafts too. I like the idea of a spacer, because then I get to keep & reuse the 682 driveshaft. I've already got a broken KT17 that needs a resting place, I'd prefer not to add an otherwise useable driveshaft to the list. |
#13
|
||||
|
||||
Quote:
Quote:
Quote:
Attached is a picture of the pump adapter ( right ) I make. I also have a similar adapter for the splined pump too. On the left is the engine adapter for the kubota engine. |
#14
|
||||
|
||||
Quote:
A drilled driveshaft is $30 plus shipping. |
#15
|
|||
|
|||
Jeff, thank you. I sent you an email through the website here.
|
#16
|
||||
|
||||
Replied
|
#17
|
||||
|
||||
I would not fab a spacer for the driveshaft, that's asking for trouble.
I have a few engine plates laying in my garage from 186X's. If you hack it up trying to drill it and need another one, or if you just want to get one and switch it, they're out there.
__________________
1912 with Kohler M18 engine repower, CI rear, 50C deck, 364 snow blower IH Cub Original with deck #2 cart GREEN 314 with integral sleeve hitch, H2 and independent brake upgrade from a 317, and front hydraulic blade, 48" deck |
#18
|
|||
|
|||
Update. Hooked jumper cables to the CH23 & put gas down the carb; started easily and without smoke. The exact model number comes back to a SCAG zero-turn. Haven't checked compression yet; it could be really tired (but at least it runs).
Pulled the KT17; broken rod nearly punched a hole in the side of the block. Everything else (carb, manifolds, ignition, etc.) is really clean; is there a big demand for KT parts? The CH18 adapter I bought bolts up to the CH23 and the ragjoint; a trip to the hardware store for the right flywheel bolts is in order. No measurements yet on how far off the driveshaft length is. There's a really nice flat mating surface between the CH18 adapter and the ragjoint; if the length isn't far off I'll consider a spacer in there. I already need longer mounting bolts. The bolt pattern looks very similar to old American radiator fans and every go-fast catalog has a huge selection of spacers for radiator fans. I don't want to cantilever stuff too far off the surface of the flywheel The 682 electric PTO clutch slips right on, but the block has extra mounting bosses that push the clutch plate 1/8" off the block. That's preventing the clutch from being as far enough up the crank to snug against the crank flare. I'll slice off the extra bosses with a Sawzall. If folks here think it doesn't matter if the clutch is snugged up against the crank flare, I'll just make up the 1/8" for the mounting bolts with washers and leave the extra bosses alone. The crankshaft is longer than the KT (3/8-1/2" longer). Should I find washers that fit over the crank to make up the difference, or slice off the tip of the crankshaft? Note: remove the engine plate bolts from the underside of the tractor. The easily-accessible nuts are spot-welded to the engine plate. |
#19
|
|||
|
|||
Engine plate drill dimensions:
http://onlycubcadets.net/forum/showp...8&postcount=16 My CH23S appears to have a 3.5" bolt hole spacing. |
#20
|
|||
|
|||
I broke out the tape measure and looked at ragjoint mount to PTO clutch pulley lengths; the CH with the Cub Cadet adapter ends up being about 1-1/4" shorter than the old KT (imprecise measurements). Assuming the PTO clutch pulley ends up in the same location, I have about a 1-1/4" gap to make up. I hope to have an in-situ measurement tomorrow.
Ragjoint has a little bit of twist to it, but doesn't look at all degraded. |
|
|
Cub Cadet is a premium line of outdoor power equipment, established in 1961 as part of International Harvester. During the 1960s, IH initiated an entirely new line of lawn and garden equipment aimed at the owners rural homes with large yards and private gardens. There were a wide variety of Cub Cadet branded and after-market attachments available; including mowers, blades, snow blowers, front loaders, plows, carts, etc. Cub Cadet advertising at that time harped on their thorough testing by "boys - acknowledged by many as the world's worst destructive force!". Cub Cadets became known for their dependability and rugged construction.
MTD Products, Inc. of Cleveland, Ohio purchased the Cub Cadet brand from International Harvester in 1981. Cub Cadet was held as a wholly owned subsidiary for many years following this acquisition, which allowed them to operate independently. Recently, MTD has taken a more aggressive role and integrated Cub Cadet into its other lines of power equipment.
This website and forum are not affiliated with or sponsored by MTD Products Inc, which owns the CUB CADET trademarks. It is not an official MTD Products Inc, website, and MTD Products Inc, is not responsible for any of its content. The official MTD Products Inc, website can be found at: http://www.mtdproducts.com. The information and opinions expressed on this website are the responsibility of the website's owner and/or it's members, and do not represent the opinions of MTD Products Inc. IH, INTERNATIONAL HARVESTER are registered trademark of CNH America LLC
All material, images, and graphics from this site are the property of www.onlycubcadets.net. Any unauthorized use, reproductions, or duplications are prohibited unless solely expressed in writing.
Cub Cadet, Cub, Cadet, IH, MTD, Parts, Tractors, Tractor, International Harvester, Lawn, Garden, Lawn Mower, Kohler, garden tractor equipment, lawn garden tractors, antique garden tractors, garden tractor, PTO, parts, online, Original, 70, 71, 72, 73, 76, SO76, 80, 81, 86, 100, 102, 104, 105, 106, 107, 108,109, 122, 123, 124, 125, 126, 127, 128, 129, 147, 149, 169, 182, 282, 382, 482, 580, 582, 582 Special, 680, 682, 782, 782D, 784, 800, 805, 882, 982, 984, 986, 1000, 1015, 1100, 1105, 1110, 1200, 1250, 1282, 1450, 1512, 1604, 1605, 1606, 1610, 1615, 1620, 1650, 1710, 1711, 1712, 1806, 1810, 1811, 1812, 1912, 1914.