PLEASE PATRONIZE OUR SPONSORS!
|
|
Thread Tools | Display Modes |
#21
|
|||
|
|||
Before you go making spacers, you need to check to make sure the engine has all 4 spacers under it. Perhaps the rear ones are missing.
#2 in the pic: 1811 em.jpg The QA42A will go on an 1811 with no issues. No spacer washers needed. Your engine has to not be mounted correctly, or the pulley is wrong. You did change the pulley, correct? The one that it uses for the 1250 will not work with the necessary 5/8" belt the 1811 uses. I've ran a QA42A on my 1811 one year when the 450 broke and I was waiting for parts. Mounted right up, no issues. https://www.youtube.com/watch?v=gqK5r10xKBc&t=75s |
#22
|
||||
|
||||
J-Mech, good catch and thanks for the good advice. I will check for engine spacers tomorrow. The PO had put a 5/8 pulley on the thrower already.
__________________
Rusty 149 project with: QA42 snow thrower 38" deck Barn fresh 1811 with: 44c mowing deck QA42A snow thrower 42" snow blade |
#23
|
|||
|
|||
While I'm noticing things.....
When you repaired your front axle, you put the bolt in backwards that prevents the axle from rocking. The bolt head is supposed to face the axle and it should have a thin walled jam nut on front to lock it in place. Wears better when it is installed correctly. 1811axle.jpg |
#24
|
||||
|
||||
I just replaced the worn castle nut and bolt with a longer bolt and used two nuts to lock it. Are you saying the frame or axle are supposed to be threaded? If so the threads are worn away. The bolt slipped right through them both. The frame is a C-channel so I tightened the first nut until the axle didn't wobble but was free to pivot, then jambed it with the second nut.
__________________
Rusty 149 project with: QA42 snow thrower 38" deck Barn fresh 1811 with: 44c mowing deck QA42A snow thrower 42" snow blade |
#25
|
|||
|
|||
That's my mistake. The bolt I circled I now see is the center pivot bolt. It is installed correctly.
However, upon closer inspection, on the far end I can see the bolt I was thinking of. It appears pretty loose. (It's under the red circle at the 9 o'clock position.) There are two bolts that go through a "flap" (for lack of a better term) in the frame just in front of the axle. One on each side. Tightening them towards the axle takes the side to side play out of the axle. They are supposed to lightly rub the axle. Make sure they are adjusted correctly, and all is good. I keep a little bit of oil or grease on the head of mine when I grease the tractor. Keeps it from wearing the axle and bolt out. Plus, sometimes they squeak and it gets annoying. That axle was worn pretty bad. Probably needed a bushing installed..... |
#26
|
||||
|
||||
Quote:
I received straight links because I didn't read all the way to the bottom of the description. I asked them to remedy this for me. I should have bought from Extreme.
__________________
Rusty 149 project with: QA42 snow thrower 38" deck Barn fresh 1811 with: 44c mowing deck QA42A snow thrower 42" snow blade |
#27
|
|||
|
|||
"TOP LINKS ARE STRAIGHT (Not As Shown) "
Piss poor advertising. A responsible Vendor would have shown the actual part instead of mis-leading their customers.
__________________
Roland Bedell CC Models: 100, 105, 1450, 782, (2) 784, & 2072 Buy: Made in the USA |
#28
|
||||
|
||||
After emailing ihccw and complaining about the misleading listing for top links they refunded the money for the links and apologized.
Customer service like that will get my business again.
__________________
Rusty 149 project with: QA42 snow thrower 38" deck Barn fresh 1811 with: 44c mowing deck QA42A snow thrower 42" snow blade |
#29
|
||||
|
||||
Putting final touches on the QA42A
I shimmed the gearbox out from it's mounting plate to align the pulleys. I used two washers on top and 5 on the bottom. Then I added a 1"x3"x1/8" spacer on the top and bottom after I filled them into a wedge shape so that the gearbox had flat mounting surfaces.
I also flipped the pulley around to move it as far forward as possible. It lines up well with the top pulley. Pic on right is before shimming.
__________________
Rusty 149 project with: QA42 snow thrower 38" deck Barn fresh 1811 with: 44c mowing deck QA42A snow thrower 42" snow blade |
#30
|
||||
|
||||
I also flipped the scraper blade around and replaced all the carriage bolt with stainless hardware. Don't let it get as bad as this! There wasn't much blade left and the nuts were tricky to remove. That is the nut you see.
__________________
Rusty 149 project with: QA42 snow thrower 38" deck Barn fresh 1811 with: 44c mowing deck QA42A snow thrower 42" snow blade |
Thread Tools | |
Display Modes | |
|
|
Cub Cadet is a premium line of outdoor power equipment, established in 1961 as part of International Harvester. During the 1960s, IH initiated an entirely new line of lawn and garden equipment aimed at the owners rural homes with large yards and private gardens. There were a wide variety of Cub Cadet branded and after-market attachments available; including mowers, blades, snow blowers, front loaders, plows, carts, etc. Cub Cadet advertising at that time harped on their thorough testing by "boys - acknowledged by many as the world's worst destructive force!". Cub Cadets became known for their dependability and rugged construction.
MTD Products, Inc. of Cleveland, Ohio purchased the Cub Cadet brand from International Harvester in 1981. Cub Cadet was held as a wholly owned subsidiary for many years following this acquisition, which allowed them to operate independently. Recently, MTD has taken a more aggressive role and integrated Cub Cadet into its other lines of power equipment.
This website and forum are not affiliated with or sponsored by MTD Products Inc, which owns the CUB CADET trademarks. It is not an official MTD Products Inc, website, and MTD Products Inc, is not responsible for any of its content. The official MTD Products Inc, website can be found at: http://www.mtdproducts.com. The information and opinions expressed on this website are the responsibility of the website's owner and/or it's members, and do not represent the opinions of MTD Products Inc. IH, INTERNATIONAL HARVESTER are registered trademark of CNH America LLC
All material, images, and graphics from this site are the property of www.onlycubcadets.net. Any unauthorized use, reproductions, or duplications are prohibited unless solely expressed in writing.
Cub Cadet, Cub, Cadet, IH, MTD, Parts, Tractors, Tractor, International Harvester, Lawn, Garden, Lawn Mower, Kohler, garden tractor equipment, lawn garden tractors, antique garden tractors, garden tractor, PTO, parts, online, Original, 70, 71, 72, 73, 76, SO76, 80, 81, 86, 100, 102, 104, 105, 106, 107, 108,109, 122, 123, 124, 125, 126, 127, 128, 129, 147, 149, 169, 182, 282, 382, 482, 580, 582, 582 Special, 680, 682, 782, 782D, 784, 800, 805, 882, 982, 984, 986, 1000, 1015, 1100, 1105, 1110, 1200, 1250, 1282, 1450, 1512, 1604, 1605, 1606, 1610, 1615, 1620, 1650, 1710, 1711, 1712, 1806, 1810, 1811, 1812, 1912, 1914.