Only Cub Cadets

PLEASE PATRONIZE OUR SPONSORS!

CC Speciaalties R. F. Houtz and Sons

Patton Acres IH Cub Cadet Parts

Cub Cadet Parts & Service


If you would like to help maintain this site & enhance it, feel free to donate whatever amount you would like to!




Attention Folks we have a new owner!
Greg Rozar AKA- CubDieselFan


Go Back   Only Cub Cadets > Cub Cadets > Implements and Attachments

Notices

Reply
 
Thread Tools Display Modes
  #1  
Old 09-11-2022, 08:23 PM
gost530 gost530 is offline
Member
 
Join Date: Jun 2011
Location: Oxford, Ohio
Posts: 34
Default #2 Tiller, 1211 vs 149

I recently installed a number 2 tiller on my 149. Tiller works great but speed control on the 149 is difficult. I also have a 1211. Will the lift from the 149, and belt fit the 1211? Would the 1211 be a better choice for the tiller?
Thanks in advance,

Gary
Reply With Quote
  #2  
Old 09-15-2022, 07:57 PM
Merk Merk is offline
Grand Member
 
Join Date: Mar 2009
Location: Ohio
Posts: 2,180
Default

Any hydro is more difficult to control speed when tilling. I will take a manual trans IH Cub Cadet any day over a hydro Cub Cadet when it comes to tilling.

My Dad purchase a new IH Cub Cadet 1450 with a tiller back in 1977. Never could a steady speed when it comes to tilling. Putting a tiller on a 1211 ????
I think the center section of the read end that holds tiller drive is aluminum. It has a few more bolts holding everything together. A 1211 PTO takes a bigger/wider belt than the 1450 does.
__________________
Project Uncle Dick
Cub Cadet 70
http://www.onlycubcadets.net/forum/s...ght=Uncle+Dick
Reply With Quote
  #3  
Old 09-16-2022, 06:14 PM
gost530 gost530 is offline
Member
 
Join Date: Jun 2011
Location: Oxford, Ohio
Posts: 34
Default

Mr Merk, Thank you for the information it appears I was wrong in thinking that a manual transmission would be to fast for a tiller. I do have a 1200 however being an old man I doubt the manual lift would work for me. You certainly saved me a lot of time and energy trying to put it on the 1211. Thanks again Gary
Reply With Quote
  #4  
Old 09-16-2022, 09:11 PM
Merk Merk is offline
Grand Member
 
Join Date: Mar 2009
Location: Ohio
Posts: 2,180
Default

I have a IH Cub Cadet 128 that I use on a tiller like yours. My 128 has a creeper unit in it to get the right speed. Creeper unit has a 4 to 1 speed reduction . My 128 has helper spring in it to help lift the tiller.
__________________
Project Uncle Dick
Cub Cadet 70
http://www.onlycubcadets.net/forum/s...ght=Uncle+Dick
Reply With Quote
  #5  
Old 09-17-2022, 08:50 PM
Ambush Ambush is online now
Senior Member
 
Join Date: Nov 2020
Location: British Columbia
Posts: 593
Default

I have a 149 and a self powered (homemade conversion) #2 tiller and it is a total pain to regulate the speed. Now my swash control springs aren't really doing their job due too wear either, though. The tiller has a 14 HP motor and the tines are over speed by about fifteen percent. If I hit a tough patch, I almost get whip lash!!
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 11:38 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.

Cub Cadet is a premium line of outdoor power equipment, established in 1961 as part of International Harvester. During the 1960s, IH initiated an entirely new line of lawn and garden equipment aimed at the owners rural homes with large yards and private gardens. There were a wide variety of Cub Cadet branded and after-market attachments available; including mowers, blades, snow blowers, front loaders, plows, carts, etc. Cub Cadet advertising at that time harped on their thorough testing by "boys - acknowledged by many as the world's worst destructive force!". Cub Cadets became known for their dependability and rugged construction.

MTD Products, Inc. of Cleveland, Ohio purchased the Cub Cadet brand from International Harvester in 1981. Cub Cadet was held as a wholly owned subsidiary for many years following this acquisition, which allowed them to operate independently. Recently, MTD has taken a more aggressive role and integrated Cub Cadet into its other lines of power equipment.

This website and forum are not affiliated with or sponsored by MTD Products Inc, which owns the CUB CADET trademarks. It is not an official MTD Products Inc, website, and MTD Products Inc, is not responsible for any of its content. The official MTD Products Inc, website can be found at: http://www.mtdproducts.com. The information and opinions expressed on this website are the responsibility of the website's owner and/or it's members, and do not represent the opinions of MTD Products Inc. IH, INTERNATIONAL HARVESTER are registered trademark of CNH America LLC

All material, images, and graphics from this site are the property of www.onlycubcadets.net. Any unauthorized use, reproductions, or duplications are prohibited unless solely expressed in writing.

Cub Cadet, Cub, Cadet, IH, MTD, Parts, Tractors, Tractor, International Harvester, Lawn, Garden, Lawn Mower, Kohler, garden tractor equipment, lawn garden tractors, antique garden tractors, garden tractor, PTO, parts, online, Original, 70, 71, 72, 73, 76, SO76, 80, 81, 86, 100, 102, 104, 105, 106, 107, 108,109, 122, 123, 124, 125, 126, 127, 128, 129, 147, 149, 169, 182, 282, 382, 482, 580, 582, 582 Special, 680, 682, 782, 782D, 784, 800, 805, 882, 982, 984, 986, 1000, 1015, 1100, 1105, 1110, 1200, 1250, 1282, 1450, 1512, 1604, 1605, 1606, 1610, 1615, 1620, 1650, 1710, 1711, 1712, 1806, 1810, 1811, 1812, 1912, 1914.