PLEASE PATRONIZE OUR SPONSORS!
|
|
Thread Tools | Display Modes |
#1
|
||||
|
||||
122 snow blade
I picked up a snow blade for my 122 recently, it looks like a brand new plow on a restored/painted narrow frame hanger, but it did not come with a lift rod. It mounts up and everything but the lift arm I have is about 2" too short. It is a reinforced lift arm from a QA42 snow thrower. I thought I read elsewhere that the lift rod should be the same between the QA42 snow thrower and the snow blade. I've made sure the block for the deck height is all the way out so that's not in the way. How long should the lift arm be for this?
__________________
1912 with Kohler M18 engine repower, CI rear, 50C deck, 364 snow blower IH Cub Original with deck #2 cart GREEN 314 with integral sleeve hitch, H2 and independent brake upgrade from a 317, and front hydraulic blade, 48" deck |
#2
|
||||
|
||||
Quote:
from chains cables to pipes/tubing and custom rod like factory and threaded adjustable ones. Thinking jeff even makes some but not sure. |
#3
|
|||
|
|||
Sponsor CCSpecialties has the IH 473924 R1 [32"] in stock.
__________________
Roland Bedell CC Models: 100, 105, 1450, 782, (2) 784, & 2072 Buy: Made in the USA |
#4
|
||||
|
||||
Well that makes sense, I measured my rods (I have two actually) and both are 27" long.
__________________
1912 with Kohler M18 engine repower, CI rear, 50C deck, 364 snow blower IH Cub Original with deck #2 cart GREEN 314 with integral sleeve hitch, H2 and independent brake upgrade from a 317, and front hydraulic blade, 48" deck |
#5
|
||||
|
||||
I got it sorted out. I used a 1/2” x 36” rod and heat bent it at the ends to 32.5”, drilled pin holes and cut off the excess 1” or so from each end. It looks good as new.
EFADDFD8-1950-4CB7-9BB4-79997E9FF6B8.jpg 8810589D-8542-4C05-AB82-7A67047CE8E5.jpg
__________________
1912 with Kohler M18 engine repower, CI rear, 50C deck, 364 snow blower IH Cub Original with deck #2 cart GREEN 314 with integral sleeve hitch, H2 and independent brake upgrade from a 317, and front hydraulic blade, 48" deck |
#6
|
||||
|
||||
Blade and lift rod both look awesome! Nice job fabricating it up. Just need some IH white on that lift rod and you are ready for plowing.
Cub Cadet 123
__________________
Still don't know what I'm doing in OHIO?.....If you find me, then please point me back toward INDIANA. |
#7
|
||||
|
||||
lift rod fab
I practiced my mig welding with a lift rod. I used a grinder to notch out a 'V' groove in some 1/2' rod, bent it over to 90degees and welded away. Looks pretty clean after a little grinding. Also bought some really thin stainless, 1/2" shim washers from McMAster and I use them on lift rods and all over the tractor. They fit where thicker washer won't.
__________________
Rusty 149 project with: QA42 snow thrower 38" deck Barn fresh 1811 with: 44c mowing deck QA42A snow thrower 42" snow blade |
#8
|
|||
|
|||
Very nice. You'll be styling when the snow flies Never windy there, ha ha.
__________________
1863, 1864, 48" and 54" mower decks, 54" snow plow, 451 snow blower, TracVac 580 |
Thread Tools | |
Display Modes | |
|
|
Cub Cadet is a premium line of outdoor power equipment, established in 1961 as part of International Harvester. During the 1960s, IH initiated an entirely new line of lawn and garden equipment aimed at the owners rural homes with large yards and private gardens. There were a wide variety of Cub Cadet branded and after-market attachments available; including mowers, blades, snow blowers, front loaders, plows, carts, etc. Cub Cadet advertising at that time harped on their thorough testing by "boys - acknowledged by many as the world's worst destructive force!". Cub Cadets became known for their dependability and rugged construction.
MTD Products, Inc. of Cleveland, Ohio purchased the Cub Cadet brand from International Harvester in 1981. Cub Cadet was held as a wholly owned subsidiary for many years following this acquisition, which allowed them to operate independently. Recently, MTD has taken a more aggressive role and integrated Cub Cadet into its other lines of power equipment.
This website and forum are not affiliated with or sponsored by MTD Products Inc, which owns the CUB CADET trademarks. It is not an official MTD Products Inc, website, and MTD Products Inc, is not responsible for any of its content. The official MTD Products Inc, website can be found at: http://www.mtdproducts.com. The information and opinions expressed on this website are the responsibility of the website's owner and/or it's members, and do not represent the opinions of MTD Products Inc. IH, INTERNATIONAL HARVESTER are registered trademark of CNH America LLC
All material, images, and graphics from this site are the property of www.onlycubcadets.net. Any unauthorized use, reproductions, or duplications are prohibited unless solely expressed in writing.
Cub Cadet, Cub, Cadet, IH, MTD, Parts, Tractors, Tractor, International Harvester, Lawn, Garden, Lawn Mower, Kohler, garden tractor equipment, lawn garden tractors, antique garden tractors, garden tractor, PTO, parts, online, Original, 70, 71, 72, 73, 76, SO76, 80, 81, 86, 100, 102, 104, 105, 106, 107, 108,109, 122, 123, 124, 125, 126, 127, 128, 129, 147, 149, 169, 182, 282, 382, 482, 580, 582, 582 Special, 680, 682, 782, 782D, 784, 800, 805, 882, 982, 984, 986, 1000, 1015, 1100, 1105, 1110, 1200, 1250, 1282, 1450, 1512, 1604, 1605, 1606, 1610, 1615, 1620, 1650, 1710, 1711, 1712, 1806, 1810, 1811, 1812, 1912, 1914.