|
PLEASE PATRONIZE OUR SPONSORS!
|
|||||||
 |
|
|
Thread Tools | Display Modes |
|
#11
09-02-2022, 06:41 AM
|
|||
|
|||
Anyone having a Installation Manual for the 190-388 and 190-389 CAT 0 3 Point Hitch #772-3351A, can you supply one so I can get it posted?
__________________
Roland Bedell CC Models: 100, 105, 1450, 782, (2) 784, & 2072 Buy: Made in the USA 
|
|
#12
09-02-2022, 07:28 AM
|
||||
|
||||
|
Just to be clear I'm asking about this original style 3pt hitch for an 82 series (straight lifting arm)..
__________________
1980 IH CC 782 1957 Cub Lo-Boy 1993 Craftsman LT4000
|
|
#13
09-02-2022, 11:03 AM
|
||||
|
||||
|
Okay, after further investigation that style pin is not on the older IH 782'S, they added that type on the CCC so the 2 pins take the load of the implement at the rear, it is not a float lockout pin.
Roland that instruction sheet is in the cyclops service manual section 7 page 3
__________________
Up to 530 and counting... I give up updating my profile!
|
|
#14
09-02-2022, 11:09 AM
|
|||
|
|||
|
Quote:
__________________
Roland Bedell CC Models: 100, 105, 1450, 782, (2) 784, & 2072 Buy: Made in the USA
|
|
#15
09-02-2022, 06:25 PM
|
||||
|
||||
|
Ah, now we're cookin. Thanks guys. Never thought to look for attachment info in a chassis service manual. I downloaded a couple of the later service manuals and noticed that apparently the only time that piece is shown is in context with the Cat 0 type 3pt hitch. Here's another version showing the lift bar connected without that piece so I'm guessing I don't really need it since I'm going with a sleeve hitch, not a Cat 0 3pt. That sound about right?
__________________
1980 IH CC 782 1957 Cub Lo-Boy 1993 Craftsman LT4000
|
|
#16
09-21-2022, 02:42 PM
|
||||
|
||||
|
Here is a side by side comparison of the regular wide frame lift bar (top) and the 82 series lift bar (bottom). The front hole is recessed to accept the head of a clevis pin. I attempted to install it today and found out that I do indeed need that piece discussed above. The front end of the lift bar hits the clevis pin before the holes to connect the lift bar line up.
__________________
1980 IH CC 782 1957 Cub Lo-Boy 1993 Craftsman LT4000
|
|
#17
09-21-2022, 05:02 PM
|
||||
|
||||
|
Well after comparing a bunch of photos I think the problem is with the repro bar. The hole at the front is drilled too far back thereby causing interference with that clevis pin. I'm wondering if I could get away with trimming off a bit. Any opinions?
__________________
1980 IH CC 782 1957 Cub Lo-Boy 1993 Craftsman LT4000
|
|
#18
09-21-2022, 07:09 PM
|
||||
|
||||
|
Is the one on the left a repro? looks factory, or is the one on the right?
__________________
Up to 530 and counting... I give up updating my profile!
|
|
#19
09-21-2022, 07:19 PM
|
||||
|
||||
|
Yeah, probably should have labeled them, sorry. Repro on the right. You can see how much closer to the end of the bar the hole is in the left photo while on the right the hole is quite a bit farther from the end and that extra distance is causing the end of the bar to hit the clevis before a pin can be inserted. I'm thinking if I trim the bar down to match the one on the left it should give me the room I need.
__________________
1980 IH CC 782 1957 Cub Lo-Boy 1993 Craftsman LT4000
|
|
#20
09-21-2022, 07:46 PM
|
||||
|
||||
|
before you do that check to see if the pin fits flush with the outside of the bar, something doesn't look right.
__________________
Up to 530 and counting... I give up updating my profile!
|
|
|
|
Cub Cadet is a premium line of outdoor power equipment, established in 1961 as part of International Harvester. During the 1960s, IH initiated an entirely new line of lawn and garden equipment aimed at the owners rural homes with large yards and private gardens. There were a wide variety of Cub Cadet branded and after-market attachments available; including mowers, blades, snow blowers, front loaders, plows, carts, etc. Cub Cadet advertising at that time harped on their thorough testing by "boys - acknowledged by many as the world's worst destructive force!". Cub Cadets became known for their dependability and rugged construction.
MTD Products, Inc. of Cleveland, Ohio purchased the Cub Cadet brand from International Harvester in 1981. Cub Cadet was held as a wholly owned subsidiary for many years following this acquisition, which allowed them to operate independently. Recently, MTD has taken a more aggressive role and integrated Cub Cadet into its other lines of power equipment.
This website and forum are not affiliated with or sponsored by MTD Products Inc, which owns the CUB CADET trademarks. It is not an official MTD Products Inc, website, and MTD Products Inc, is not responsible for any of its content. The official MTD Products Inc, website can be found at: http://www.mtdproducts.com. The information and opinions expressed on this website are the responsibility of the website's owner and/or it's members, and do not represent the opinions of MTD Products Inc. IH, INTERNATIONAL HARVESTER are registered trademark of CNH America LLC
All material, images, and graphics from this site are the property of www.onlycubcadets.net. Any unauthorized use, reproductions, or duplications are prohibited unless solely expressed in writing.
Cub Cadet, Cub, Cadet, IH, MTD, Parts, Tractors, Tractor, International Harvester, Lawn, Garden, Lawn Mower, Kohler, garden tractor equipment, lawn garden tractors, antique garden tractors, garden tractor, PTO, parts, online, Original, 70, 71, 72, 73, 76, SO76, 80, 81, 86, 100, 102, 104, 105, 106, 107, 108,109, 122, 123, 124, 125, 126, 127, 128, 129, 147, 149, 169, 182, 282, 382, 482, 580, 582, 582 Special, 680, 682, 782, 782D, 784, 800, 805, 882, 982, 984, 986, 1000, 1015, 1100, 1105, 1110, 1200, 1250, 1282, 1450, 1512, 1604, 1605, 1606, 1610, 1615, 1620, 1650, 1710, 1711, 1712, 1806, 1810, 1811, 1812, 1912, 1914.
Linear Mode
