Only Cub Cadets

PLEASE PATRONIZE OUR SPONSORS!

CC Speciaalties R. F. Houtz and Sons

Patton Acres IH Cub Cadet Parts

Cub Cadet Parts & Service


If you would like to help maintain this site & enhance it, feel free to donate whatever amount you would like to!




Attention Folks we have a new owner!
Greg Rozar AKA- CubDieselFan


Go Back   Only Cub Cadets > Cub Cadets > Cub Cadet Engines > Briggs & Stratton Engines

Notices

Reply
 
Thread Tools Display Modes
  #1  
Old 06-23-2015, 01:41 PM
Arik434 Arik434 is offline
Member
 
Join Date: Jun 2015
Location: NY
Posts: 33
Default 16 HP Vanguard voltage regulator

I picked up a project 2160 tractor that needed some work on the engine. I did a valve job and top end rebuild on it with new gaskets. It now starts up and seems to run great, but I noticed that I get the 'amp' light come on when I use the PTO. I checked the battery and it sure seems like I'm not getting a charge from the alternator system. It appears that I either have the 10 or 16 amp system--I cant tell which. It seems as though all the parts are the same except for the size of the magnets inside the flywheel. Regardless, I seem to be getting 20 volts AC out of the stator (so I'd assume its the 10 amp system). I dont have the shunt in order to measure the amperage, but the red wire out of the voltage regulator only shows 5-6 Volts DC. Does this mean I have a bad voltage regulator? It is mounted right to the side cover on the engine, but could it also be a bad ground? I guess Id just hate to buy a new regulator if thats not my issue.

Thanks for any info or advice.
Reply With Quote
  #2  
Old 06-23-2015, 03:14 PM
R Bedell R Bedell is offline
Administrator
 
Join Date: Mar 2007
Location: Michigan
Posts: 13,693
Default

Quote:
I seem to be getting 20 volts AC out of the stator
Not enough....you should be near 30VAC.
__________________
Roland Bedell

CC Models: 100, 105, 1450, 782, (2) 784, & 2072

Buy: Made in the USA
Reply With Quote
  #3  
Old 06-23-2015, 03:30 PM
ol'George's Avatar
ol'George ol'George is online now
Grand Member
 
Join Date: Oct 2009
Location: MI
Posts: 6,610
Default

Quote:
Originally Posted by R Bedell View Post
Not enough....you should be near 30VAC.
May I add near 30 Vac @ full throttle
If you measured only 20 V AC and it was @ full throttle, it sounds like a stator problem.
Reply With Quote
  #4  
Old 06-23-2015, 03:57 PM
R Bedell R Bedell is offline
Administrator
 
Join Date: Mar 2007
Location: Michigan
Posts: 13,693
Default

Quote:
near 30 Vac @ full throttle
Sorry..........that was an assumption on my part
__________________
Roland Bedell

CC Models: 100, 105, 1450, 782, (2) 784, & 2072

Buy: Made in the USA
Reply With Quote
  #5  
Old 06-23-2015, 04:10 PM
Arik434 Arik434 is offline
Member
 
Join Date: Jun 2015
Location: NY
Posts: 33
Default

Quote:
Originally Posted by R Bedell View Post
Sorry..........that was an assumption on my part
It was about half throttle. I'm curious why do you say it should be 30 Vac? I see some documentation that says it should be 20 Vac also...with the only differences in the size of magnets inside the flywheel? And since the stator and voltage regulator are the same for both, shouldn't the regulator still put out the correct DC voltage, but just at a lower amperage?

Regardless, I'll test the stator again tonight at full throttle instead of half. All the readings reference 3600 rpm, but I don't have a tachometer for it.
Reply With Quote
  #6  
Old 06-23-2015, 04:14 PM
R Bedell R Bedell is offline
Administrator
 
Join Date: Mar 2007
Location: Michigan
Posts: 13,693
Default

You need 30VAC to produce 14VDC once it is rectified and regulated.
__________________
Roland Bedell

CC Models: 100, 105, 1450, 782, (2) 784, & 2072

Buy: Made in the USA
Reply With Quote
  #7  
Old 06-23-2015, 04:27 PM
Arik434 Arik434 is offline
Member
 
Join Date: Jun 2015
Location: NY
Posts: 33
Default

Ok. The service manual says 20 Vac for 10 amp system and 30 Vac for 16 amp system. However, I dont see any way to tell which system I have without removing the flywheel and measuring the magnet sizes.
Reply With Quote
  #8  
Old 06-23-2015, 04:44 PM
ol'George's Avatar
ol'George ol'George is online now
Grand Member
 
Join Date: Oct 2009
Location: MI
Posts: 6,610
Default

Was just looking on the net for an answer and do see where some are listed @ 20 V ac--- this is a briggs right?
Try running it @ 3600 and if it comes up to near 30V you are sure it is ok.
Educated guess is regulator is bad @ 5-6 V.dc output. that is awful low.
It would be good if, as a test, before you buy, you could substitute a known good reg.
I used a 3 wire like that from a kohler on a tecumseh till the correct one arrived and it worked just fine.
Reply With Quote
  #9  
Old 06-23-2015, 06:42 PM
Sam Mac's Avatar
Sam Mac Sam Mac is offline
Administrator
 
Join Date: Feb 2010
Location: Galax VA
Posts: 18,745
Default

For what ever it's worth I've seen way too many Vanguard VR issues. To the OP if you have 30 Volts AC on the 2 red wires at wide open throttle the stator is probably OK. I have converted a number of Cubs to the Kohler VR. So far so good. This pic is a is a Vanguard with a Kohler VR..
Attached Images
File Type: jpg IMG_3064.jpg (21.1 KB, 168 views)
__________________
2264 with 54 GT deck
1641 AKA Black Jack with a 402-E Haban Sickle bar mower
JD317 dump truck
BX2670 with FEL
Reply With Quote
  #10  
Old 06-23-2015, 08:01 PM
Arik434 Arik434 is offline
Member
 
Join Date: Jun 2015
Location: NY
Posts: 33
Default

I did a test tonight at nearly full throttle and it was showing about 29 volts AC. At first the DC output voltage was up to around 10 and then it dropped to the 6 that I saw yesterday. After a minute or two I checked again and it looked like 0. The body of the VR seems grounded just fine, so maybe it's just bad?

What model kohler unit are you using? Hopefully that's all that's wrong here.
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 06:46 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.

Cub Cadet is a premium line of outdoor power equipment, established in 1961 as part of International Harvester. During the 1960s, IH initiated an entirely new line of lawn and garden equipment aimed at the owners rural homes with large yards and private gardens. There were a wide variety of Cub Cadet branded and after-market attachments available; including mowers, blades, snow blowers, front loaders, plows, carts, etc. Cub Cadet advertising at that time harped on their thorough testing by "boys - acknowledged by many as the world's worst destructive force!". Cub Cadets became known for their dependability and rugged construction.

MTD Products, Inc. of Cleveland, Ohio purchased the Cub Cadet brand from International Harvester in 1981. Cub Cadet was held as a wholly owned subsidiary for many years following this acquisition, which allowed them to operate independently. Recently, MTD has taken a more aggressive role and integrated Cub Cadet into its other lines of power equipment.

This website and forum are not affiliated with or sponsored by MTD Products Inc, which owns the CUB CADET trademarks. It is not an official MTD Products Inc, website, and MTD Products Inc, is not responsible for any of its content. The official MTD Products Inc, website can be found at: http://www.mtdproducts.com. The information and opinions expressed on this website are the responsibility of the website's owner and/or it's members, and do not represent the opinions of MTD Products Inc. IH, INTERNATIONAL HARVESTER are registered trademark of CNH America LLC

All material, images, and graphics from this site are the property of www.onlycubcadets.net. Any unauthorized use, reproductions, or duplications are prohibited unless solely expressed in writing.

Cub Cadet, Cub, Cadet, IH, MTD, Parts, Tractors, Tractor, International Harvester, Lawn, Garden, Lawn Mower, Kohler, garden tractor equipment, lawn garden tractors, antique garden tractors, garden tractor, PTO, parts, online, Original, 70, 71, 72, 73, 76, SO76, 80, 81, 86, 100, 102, 104, 105, 106, 107, 108,109, 122, 123, 124, 125, 126, 127, 128, 129, 147, 149, 169, 182, 282, 382, 482, 580, 582, 582 Special, 680, 682, 782, 782D, 784, 800, 805, 882, 982, 984, 986, 1000, 1015, 1100, 1105, 1110, 1200, 1250, 1282, 1450, 1512, 1604, 1605, 1606, 1610, 1615, 1620, 1650, 1710, 1711, 1712, 1806, 1810, 1811, 1812, 1912, 1914.