PLEASE PATRONIZE OUR SPONSORS!
|
|
Thread Tools | Display Modes |
#1
|
||||
|
||||
551 blower lift rod help
While blowing snow this morning, more like slush, I had a clog so I lifted the blower to clear the clog and my lift rod that goes from the lift arm to the blower turned into a U and knocked the side panel off the hood from the extra weight of the jam of slush and snow. I was able to get it off and heat it with a torch, and hammer bend it back relatively the way it was and I almost got finished and it bent again. Clearly it’s weakened now. I’m thinking I might have one made. Is it anything special metal wise? I seems hollow. It also seems like it should have some reinforcement at the factory bend. Because that’s where it kinked.
__________________
1912 with Kohler M18 engine repower, CI rear, 50C deck, 364 snow blower IH Cub Original with deck #2 cart GREEN 314 with integral sleeve hitch, H2 and independent brake upgrade from a 317, and front hydraulic blade, 48" deck |
#2
|
|||
|
|||
All the Lift Rods I ever seen have been 1/2" Round Solid Steel.
__________________
Roland Bedell CC Models: 100, 105, 1450, 782, (2) 784, & 2072 Buy: Made in the USA |
#3
|
||||
|
||||
This is way bigger than 1/2”. It’s 1” thick. I doubt I bent 1” solid steel
2F97E42C-5AC3-477D-9402-40A05A8A23CE.jpg 21E3BD4A-0145-47EA-81AD-5777A6E38C07.jpg
__________________
1912 with Kohler M18 engine repower, CI rear, 50C deck, 364 snow blower IH Cub Original with deck #2 cart GREEN 314 with integral sleeve hitch, H2 and independent brake upgrade from a 317, and front hydraulic blade, 48" deck |
#4
|
|||
|
|||
It "looks" like 1" tubing. I would agree, it looks weakened.
__________________
Roland Bedell CC Models: 100, 105, 1450, 782, (2) 784, & 2072 Buy: Made in the USA |
#5
|
||||
|
||||
Think a push rod made from square stock or tubing would fare better than round myself
__________________
1- 1864 Dual hyd, cat 0, axle braces 1- 1450 Dual Stick w/ power steering 1- 1200 in pieces 1- 1864 in pieces QA36A Thrower, #1 Tiller w/ extensions, IH windbreaker, IH wheel weights, 44C mower deck, 50C mower deck, CCC 54" Blade, GT46 high vacuum deck, GT54 deck, Cub Tripple Bagger, Custom dozer blade, Custom suitcase weights, 3pt cultivator, lawn sweeper, original R-Bucket |
#6
|
|||
|
|||
I bent mine yesterday too from trying to use it when the linkage was over-center. Lesson learned for the future. I hear it's a fairly common problem. The lift mechanism for these isn't the best, IMO. Be grateful it was that lift rod and not your rockshaft.
I just bent the tip of mine, so I'm thinking about machining a little "sleeve" to go around the tip and re-enforce it to see if I can keep it from bending there again. They are still available from MTD. I don't think they would be too hard to make though.
__________________
125, 127, 2x IH 682, 2x IH 782, 2084, 3225, 2x3240 |
#7
|
|||
|
|||
If someone starts making a heavy duty one i might be interested in one as i see this happening to mine as well lol.
|
#8
|
||||
|
||||
I made 2 of these yesterday for my plows. I welded nuts to either end of an appropriately sized length of conduit, took 1/2" × 8" "L" or anchor bolts, drilled them for cotter pins, tacked on washers, and added a spring assist for the 106.
There's slop in the threads. They're the weak point in the design, and if it fails it will be the thread in the nut. If someone with a lathe would drill and tap a couple inches of thread into either end of a heavy rod or appropriate sized tube, it would be quite beefy. Reverse threading one end would make adjustability that much easier. We got 3/4 of an inch of snow last night and I plowed my whole block in 3rd gear without breaking anything.
__________________
Grumpy old 149/1A tiller, Trusty Rusty 106, & a Massey Ferguson 10 to work the garden, Tiny Snapper to mow the lawn. Slowly accumulating attachments and quickly driving the neighbors crazy on a half acre homestead. |
#9
|
|||
|
|||
weld a piece of angle iron onto the side of it to reinforce it
|
#10
|
|||
|
|||
Quote:
It looks like it works well for that application, but it's a whole different system. That rod lifts when it's in tension. The rod on a 450/451/551 lifts in compression.
__________________
125, 127, 2x IH 682, 2x IH 782, 2084, 3225, 2x3240 |
|
|
Cub Cadet is a premium line of outdoor power equipment, established in 1961 as part of International Harvester. During the 1960s, IH initiated an entirely new line of lawn and garden equipment aimed at the owners rural homes with large yards and private gardens. There were a wide variety of Cub Cadet branded and after-market attachments available; including mowers, blades, snow blowers, front loaders, plows, carts, etc. Cub Cadet advertising at that time harped on their thorough testing by "boys - acknowledged by many as the world's worst destructive force!". Cub Cadets became known for their dependability and rugged construction.
MTD Products, Inc. of Cleveland, Ohio purchased the Cub Cadet brand from International Harvester in 1981. Cub Cadet was held as a wholly owned subsidiary for many years following this acquisition, which allowed them to operate independently. Recently, MTD has taken a more aggressive role and integrated Cub Cadet into its other lines of power equipment.
This website and forum are not affiliated with or sponsored by MTD Products Inc, which owns the CUB CADET trademarks. It is not an official MTD Products Inc, website, and MTD Products Inc, is not responsible for any of its content. The official MTD Products Inc, website can be found at: http://www.mtdproducts.com. The information and opinions expressed on this website are the responsibility of the website's owner and/or it's members, and do not represent the opinions of MTD Products Inc. IH, INTERNATIONAL HARVESTER are registered trademark of CNH America LLC
All material, images, and graphics from this site are the property of www.onlycubcadets.net. Any unauthorized use, reproductions, or duplications are prohibited unless solely expressed in writing.
Cub Cadet, Cub, Cadet, IH, MTD, Parts, Tractors, Tractor, International Harvester, Lawn, Garden, Lawn Mower, Kohler, garden tractor equipment, lawn garden tractors, antique garden tractors, garden tractor, PTO, parts, online, Original, 70, 71, 72, 73, 76, SO76, 80, 81, 86, 100, 102, 104, 105, 106, 107, 108,109, 122, 123, 124, 125, 126, 127, 128, 129, 147, 149, 169, 182, 282, 382, 482, 580, 582, 582 Special, 680, 682, 782, 782D, 784, 800, 805, 882, 982, 984, 986, 1000, 1015, 1100, 1105, 1110, 1200, 1250, 1282, 1450, 1512, 1604, 1605, 1606, 1610, 1615, 1620, 1650, 1710, 1711, 1712, 1806, 1810, 1811, 1812, 1912, 1914.