|
PLEASE PATRONIZE OUR SPONSORS!
|
|||||||
 |
|
|
Thread Tools | Display Modes |
|
#1
02-18-2014, 02:33 PM
|
|||
|
|||
CC 1772 Diesel Driveshaft Brass Bushing
New-to-me tractor of this type.....After changing the alternator belt, I noticed there was a brass (or bronze) bushing that almost fell out while trying to re-install the driveshaft to the engine. Without much luck from a Cub Cadet dealer or the internet parts diagrams; I decided to remove the entire driveshaft to get a closer look and so I could take some pictures to hopefully get some help on the forum. In these pictures you can see the worn out bushing and where it fits. It fits inside that round rubber type disk.....that is where it fell out of at least. I am thinking that the bushing is part of that rubber disk housing as 1 unit, but I am not sure about that. What do you all think? Also, notice the fins on the plastic fan; they are buggered up a little....will that be ok to leave as-is? I need to get the parts ordered so I can get the 1772 back up and running.
Thanks for any input you can give 
|
|
#3
02-18-2014, 02:39 PM
|
|||
|
|||
|
I know. Trying to upload them through my phone because my internet browser would not even let me make a post. I can email them to someone of that will help
|
|
#4
02-18-2014, 05:01 PM
|
||||
|
||||
|
read thru this whole thread. this should give you some in site on the diesel drive shafts that we all despise.
http://www.onlycubcadets.net/forum/s...ad.php?t=25516
__________________
127 - 48'' deck + tiller. 1512- 46" GT deck & bagger 1872- 60" Haban 1772 turbo diesel- Iron rear + KW loader + backhoe + 3 point. Case 580CK Ford 850 International TD-8E
|
|
#5
02-18-2014, 06:03 PM
|
|||
|
|||
|
Oh wow.....just read through all of that. It really discourages and intimidates me though because I know nothing about doing repairs that intensive. I was just trying to re-install the driveshaft when I noticed that the bushing was worn out. It would be really really nice to do that conversion though. I'm going to upload pics of my driveshaft when I get home....hopefully if it'll work.
|
|
#6
02-18-2014, 06:04 PM
|
|||
|
|||
|
pictures.....
|
|
#7
02-18-2014, 07:12 PM
|
|||
|
|||
|
While the upgrade may be an improvement I think that bushing is available. As long as your driveshaft end is fine it will take about 1 minute to put a replacement bushing into the steel plate. From your photos it seems that part of the bushing is still in the steel plate. I had to replace one on a 1512 which uses the same part number for the plate (903-1005a). I basically took the part into the local cub cadet dealer and they handed me a replacement bushing.
You might want to look into part number 941-3004 (SELF-ALIGNING BALL BUSHING). Not sure if it will fit but would be worth looking into. I think the bushing was used on many Cubs so a local dealer may have one in-stock. Good Luck
|
|
#8
02-18-2014, 07:40 PM
|
|||
|
|||
|
Sorry forgot to mention the bushing is actually in the metal plate not the rubber disks. I copied your picture and put a red arrow onto what I think is part of the old bushing. I think if you look closely at it and the picture of the bushing I put up you will see what I mean.
I would look closely at your end of the driveshaft. It looks worn from your photo but it is tough to tell.
|
|
#9
02-18-2014, 08:48 PM
|
||||
|
||||
|
Quote:
|
|
#10
02-18-2014, 10:12 PM
|
|||
|
|||
|
Quote:
http://www.onlycubcadets.net/forum/a...1&d=1392779894
|
|
|
|
Cub Cadet is a premium line of outdoor power equipment, established in 1961 as part of International Harvester. During the 1960s, IH initiated an entirely new line of lawn and garden equipment aimed at the owners rural homes with large yards and private gardens. There were a wide variety of Cub Cadet branded and after-market attachments available; including mowers, blades, snow blowers, front loaders, plows, carts, etc. Cub Cadet advertising at that time harped on their thorough testing by "boys - acknowledged by many as the world's worst destructive force!". Cub Cadets became known for their dependability and rugged construction.
MTD Products, Inc. of Cleveland, Ohio purchased the Cub Cadet brand from International Harvester in 1981. Cub Cadet was held as a wholly owned subsidiary for many years following this acquisition, which allowed them to operate independently. Recently, MTD has taken a more aggressive role and integrated Cub Cadet into its other lines of power equipment.
This website and forum are not affiliated with or sponsored by MTD Products Inc, which owns the CUB CADET trademarks. It is not an official MTD Products Inc, website, and MTD Products Inc, is not responsible for any of its content. The official MTD Products Inc, website can be found at: http://www.mtdproducts.com. The information and opinions expressed on this website are the responsibility of the website's owner and/or it's members, and do not represent the opinions of MTD Products Inc. IH, INTERNATIONAL HARVESTER are registered trademark of CNH America LLC
All material, images, and graphics from this site are the property of www.onlycubcadets.net. Any unauthorized use, reproductions, or duplications are prohibited unless solely expressed in writing.
Cub Cadet, Cub, Cadet, IH, MTD, Parts, Tractors, Tractor, International Harvester, Lawn, Garden, Lawn Mower, Kohler, garden tractor equipment, lawn garden tractors, antique garden tractors, garden tractor, PTO, parts, online, Original, 70, 71, 72, 73, 76, SO76, 80, 81, 86, 100, 102, 104, 105, 106, 107, 108,109, 122, 123, 124, 125, 126, 127, 128, 129, 147, 149, 169, 182, 282, 382, 482, 580, 582, 582 Special, 680, 682, 782, 782D, 784, 800, 805, 882, 982, 984, 986, 1000, 1015, 1100, 1105, 1110, 1200, 1250, 1282, 1450, 1512, 1604, 1605, 1606, 1610, 1615, 1620, 1650, 1710, 1711, 1712, 1806, 1810, 1811, 1812, 1912, 1914.
Linear Mode
