Only Cub Cadets

PLEASE PATRONIZE OUR SPONSORS!

CC Specialties R. F. Houtz and Sons Jeff in Pa.

P&K Cub Cadet Machtech Direct

Cub Cadet Parts & Service


If you would like to help maintain this site & enhance it, feel free to donate whatever amount you would like to!




Attention Guest, We have turned off the forum to guest. This is due to bots attacking the site. It is still free to register.

-->
Go Back   Only Cub Cadets > Cub Cadets > IH Cub Cadet Tractors (GT)

Notices

Reply
 
Thread Tools Display Modes
  #1  
Old 07-04-2019, 10:58 PM
suburban man suburban man is offline
New Member
 
Join Date: Apr 2010
Location: Ohio
Posts: 14
Default Cub cadet 100 PTO clutch bearing race removal

Well today I found out what the noise was as my PTO bearing failed on my cub 100. I have the clutch assembly off and the locking collar loose on the bearing race. I have tried unsuccessfully for hours to pull the race off the shaft. I put a 3 jaw puller into the bearing race groove where the balls used to roll....I have 3 hose clamps holding the jaws into the shallow groove. I heated it.....quenched it.....brass hammered it....tapped chisel on race.....wont budge. I'm afraid as it failed it may have spun on the shaft and galled itself onto the shaft. I am almost ready to weld a nut onto the race and drive a 3/4" bolt against shaft to drive it off.....or cut it off with a mini cut off wheel in a dremel. Any thoughts?
Reply With Quote
  #2  
Old 07-04-2019, 11:20 PM
athomas's Avatar
athomas athomas is offline
Senior Member
 
Join Date: Dec 2011
Location: New Florence, PA
Posts: 575
Default

Worth a try to split it with the cut off wheel, or split it on 2 sides and it should separate .
Reply With Quote
  #3  
Old 07-05-2019, 07:42 AM
ironman's Avatar
ironman ironman is offline
Grand Member
 
Join Date: Sep 2012
Location: Pennsylvania
Posts: 2,590
Default

You might need more power than a Dremel puts out for the cut, but I agree with the split method. Make one cut all the way through to the keyway slot on the crank, another partially through on the opposite side. Support the crank with a block of wood, put a chisel in the keyway side cut and whack it.
Reply With Quote
  #4  
Old 07-05-2019, 09:31 AM
suburban man suburban man is offline
New Member
 
Join Date: Apr 2010
Location: Ohio
Posts: 14
Default Its off!

It is off!!!!! I soaked it with Kroil oil overnight.....put pressure on the puller .....put a little heat on it and crack!!! it jumped an 1/8th of an inch!
I was thinking dremel because small wheel would fit close to the bearing retainer lock ring. now a new bearing...clutch disc....belt and its good for another 55 years.

Reply With Quote
  #5  
Old 07-05-2019, 10:01 AM
R Bedell R Bedell is offline
Founding Member
 
Join Date: Mar 2007
Location: Michigan
Posts: 13,693
Default

Glad to hear of the success.

__________________
[B]Roland Bedell[/B]

CC Models: 100, 105, 1450, 782, (2) 784, & 2072

[SIZE="4"][B][COLOR="Red"]Buy:[/COLOR][COLOR="Blue"] Made in the USA[/COLOR][/B] [/SIZE]:American Flag 1:
Reply With Quote
  #6  
Old 07-05-2019, 11:20 AM
athomas's Avatar
athomas athomas is offline
Senior Member
 
Join Date: Dec 2011
Location: New Florence, PA
Posts: 575
Default

GoodDeal !!
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 01:24 PM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2025, vBulletin Solutions Inc.

Cub Cadet is a premium line of outdoor power equipment, established in 1961 as part of International Harvester. During the 1960s, IH initiated an entirely new line of lawn and garden equipment aimed at the owners rural homes with large yards and private gardens. There were a wide variety of Cub Cadet branded and after-market attachments available; including mowers, blades, snow blowers, front loaders, plows, carts, etc. Cub Cadet advertising at that time harped on their thorough testing by "boys - acknowledged by many as the world's worst destructive force!". Cub Cadets became known for their dependability and rugged construction.

MTD Products, Inc. of Cleveland, Ohio purchased the Cub Cadet brand from International Harvester in 1981. Cub Cadet was held as a wholly owned subsidiary for many years following this acquisition, which allowed them to operate independently. Recently, MTD has taken a more aggressive role and integrated Cub Cadet into its other lines of power equipment.

This website and forum are not affiliated with or sponsored by MTD Products Inc, which owns the CUB CADET trademarks. It is not an official MTD Products Inc, website, and MTD Products Inc, is not responsible for any of its content. The official MTD Products Inc, website can be found at: http://www.mtdproducts.com. The information and opinions expressed on this website are the responsibility of the website's owner and/or it's members, and do not represent the opinions of MTD Products Inc. IH, INTERNATIONAL HARVESTER are registered trademark of CNH America LLC

All material, images, and graphics from this site are the property of www.onlycubcadets.net. Any unauthorized use, reproductions, or duplications are prohibited unless solely expressed in writing.

Cub Cadet, Cub, Cadet, IH, MTD, Parts, Tractors, Tractor, International Harvester, Lawn, Garden, Lawn Mower, Kohler, garden tractor equipment, lawn garden tractors, antique garden tractors, garden tractor, PTO, parts, online, Original, 70, 71, 72, 73, 76, SO76, 80, 81, 86, 100, 102, 104, 105, 106, 107, 108,109, 122, 123, 124, 125, 126, 127, 128, 129, 147, 149, 169, 182, 282, 382, 482, 580, 582, 582 Special, 680, 682, 782, 782D, 784, 800, 805, 882, 982, 984, 986, 1000, 1015, 1100, 1105, 1110, 1200, 1250, 1282, 1450, 1512, 1604, 1605, 1606, 1610, 1615, 1620, 1650, 1710, 1711, 1712, 1806, 1810, 1811, 1812, 1912, 1914.