|
PLEASE PATRONIZE OUR SPONSORS!
|
|||||||
|
|
Thread Tools | Display Modes |
|
#1
09-19-2011, 11:12 AM
|
||||
|
||||
782 Restoration
Not sure where to post this - since I am looking for information and input more than it being a referance thread??
I figured since the weather is starting to cool off and the nasty white stuff will be upon us soon, I should start doing some homework. Have had frost here the past two nights, poor garden has taken a beating to say the least. If all goes well, this is going to be one of my winter projects and hopefully finished for spring planting in the garden. I was fortunate to pick up an IH built 782 about 4 or 5 months ago with a series II engine in it. Came with a rough 42" deck, 2 sets of wheel weights and quite a few scratches and some dents in the sheet metal. The tires on the rear look original and are in pretty decent shape, some normal cracking which I chock up to being a regular thing. Front tires are either very much original OR someone has figured out how to do break stands with them, cause they are bald as a baby's @$$! Also had 4 decent hub caps that cleaned up fairly good with some Mother's Chrome & Mag polish. I just couldn't wait until winter to see how they cleaned up. Question I have.... I am looking for input/opinons on what ALL should be done if I was to do a front to back restoration of this tractor properly. YES, I am going to paint it the correct IH red since there is just way too many scratches on it not to do it properly. Don't worry - the Correct Police can not say anything, my 982 is still original I brought home a parts tractor the other day to go along with this 782 - it too is also an IH built tractor. So I now have the correct grill emblem as well as a new hood bird. So what are the normal things that "should" or "need" to be replaced? Things like rag joints, gaskets, bearings, seals, etc. I am thinking if I have the tractor stripped, it should be done. But what things can you get away with NOT replacing since it will not make a difference or it isn't worth the money? Last thing I want to do is have everything stripped down and fixed up and then have a stupid $1.25 gasket or seal crap out on me! What is the best way to strip down the frame, sheet metal, rims, etc ..... sand blaster, wire wheel, emery clothe...? How is the best way to clean the plastic dash without removing the markings on it - just pain soap and a scrub brush? Where is the best place to buy tie rod ends - local Cub dealer or a sight sponsor? I eventually plan on putting on some Firestone 23 degree ags. My understaning Miller Tire has now put the 24" into production again thanks to their own personal effort in keeping these on the market. Is this true? If so, has anyone purchased any from them? You like them? Are they worth the $$$ ? Any input you have to share would be great. Thank you in advance.
__________________
Mike Ontario, Canada IH built 982, IH built 782, IH built 782 parts tractor, 100 w/fenders & lights, #4 trailer, 42" front blade, IH 2B tiller, 12" Brinly plow, Brinly cultivator, IH push mower, Sims cab, IH snowthrower, 450 blower.  Now everyone wants a Cub!  Beware of the Wife
|
|
|
Cub Cadet is a premium line of outdoor power equipment, established in 1961 as part of International Harvester. During the 1960s, IH initiated an entirely new line of lawn and garden equipment aimed at the owners rural homes with large yards and private gardens. There were a wide variety of Cub Cadet branded and after-market attachments available; including mowers, blades, snow blowers, front loaders, plows, carts, etc. Cub Cadet advertising at that time harped on their thorough testing by "boys - acknowledged by many as the world's worst destructive force!". Cub Cadets became known for their dependability and rugged construction.
MTD Products, Inc. of Cleveland, Ohio purchased the Cub Cadet brand from International Harvester in 1981. Cub Cadet was held as a wholly owned subsidiary for many years following this acquisition, which allowed them to operate independently. Recently, MTD has taken a more aggressive role and integrated Cub Cadet into its other lines of power equipment.
This website and forum are not affiliated with or sponsored by MTD Products Inc, which owns the CUB CADET trademarks. It is not an official MTD Products Inc, website, and MTD Products Inc, is not responsible for any of its content. The official MTD Products Inc, website can be found at: http://www.mtdproducts.com. The information and opinions expressed on this website are the responsibility of the website's owner and/or it's members, and do not represent the opinions of MTD Products Inc. IH, INTERNATIONAL HARVESTER are registered trademark of CNH America LLC
All material, images, and graphics from this site are the property of www.onlycubcadets.net. Any unauthorized use, reproductions, or duplications are prohibited unless solely expressed in writing.
Cub Cadet, Cub, Cadet, IH, MTD, Parts, Tractors, Tractor, International Harvester, Lawn, Garden, Lawn Mower, Kohler, garden tractor equipment, lawn garden tractors, antique garden tractors, garden tractor, PTO, parts, online, Original, 70, 71, 72, 73, 76, SO76, 80, 81, 86, 100, 102, 104, 105, 106, 107, 108,109, 122, 123, 124, 125, 126, 127, 128, 129, 147, 149, 169, 182, 282, 382, 482, 580, 582, 582 Special, 680, 682, 782, 782D, 784, 800, 805, 882, 982, 984, 986, 1000, 1015, 1100, 1105, 1110, 1200, 1250, 1282, 1450, 1512, 1604, 1605, 1606, 1610, 1615, 1620, 1650, 1710, 1711, 1712, 1806, 1810, 1811, 1812, 1912, 1914.
Threaded Mode