Only Cub Cadets

PLEASE PATRONIZE OUR SPONSORS!

CC Specialties R. F. Houtz and Sons Jeff in Pa.

P&K Cub Cadet Machtech Direct

Cub Cadet Parts & Service


If you would like to help maintain this site & enhance it, feel free to donate whatever amount you would like to!




Attention Guest, We have turned off the forum to guest. This is due to bots attacking the site. It is still free to register.

-->
Go Back   Only Cub Cadets > Cub Cadets > IH Cub Cadet Tractors (GT)

Notices

 
 
Thread Tools Display Modes
Prev Previous Post   Next Post Next
  #1  
Old 02-15-2014, 09:44 PM
john hall's Avatar
john hall john hall is offline
Grand Member
 
Join Date: Jul 2009
Location: Durham, NC
Posts: 3,095
Default 982 engine mounting plate

Had an opportunity to spend some quality time with the 982 today. Tinkered with the carb some more and now it runs without the choke on. Its nice to be able to disassemble and rod out the carb with it on the machine. After that successful venture we decided to reinstall the grill. The grill fell out on the way home and miraculously didn't bounce of the trailer!
Not only are the springs that hold the grill in missing, the grill is rubbing one of the muffler exhaust ports. Turns out that one of the muffler braces had slid loose from behind the clutch. I pulled the clutch to make sure nothing funny was going on. That's when I noticed the engine was in the mower crooked. About the only thing I had to go on was the grill housing and it looks very centered on the frame. So I loosened the engine and slipped it around a bit. Upon tightening one of the front bolts I noticed the mounting plate lifting up. I finished tightening the engine and then proceeded to address the plate issue. As best as I can figure out, there are supposed to be 6 bolts (3 in each side) in this plate---I only have two, one at each back (driveshaft) corner. To further complicate the issue, both of those bolts and the ones holding down the engine are fairly new. I can't understand exactly what someone was doing to pull all the bolts. There is no evidence of recent mechanic work on the engine, unless it was pulled to work on the starter or get to the flywheel. Fortunately the mounting plate does not appear to be broken, just in need of more bolts. Should I just assume this was sloppy mechanic work or is there another issue going on here? I can't see the mower dropping out all 10 bolts. I haven't put the missing bolts in yet, waiting to see if anyone here knows of any nasty surprises. I've attached a photo that shows a nut welded to the plate so you know exactly where I'm talking about.
Attached Images
File Type: jpg 0215141623b.jpg (30.3 KB, 83 views)
Reply With Quote
 


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 07:39 PM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2026, vBulletin Solutions Inc.

Cub Cadet is a premium line of outdoor power equipment, established in 1961 as part of International Harvester. During the 1960s, IH initiated an entirely new line of lawn and garden equipment aimed at the owners rural homes with large yards and private gardens. There were a wide variety of Cub Cadet branded and after-market attachments available; including mowers, blades, snow blowers, front loaders, plows, carts, etc. Cub Cadet advertising at that time harped on their thorough testing by "boys - acknowledged by many as the world's worst destructive force!". Cub Cadets became known for their dependability and rugged construction.

MTD Products, Inc. of Cleveland, Ohio purchased the Cub Cadet brand from International Harvester in 1981. Cub Cadet was held as a wholly owned subsidiary for many years following this acquisition, which allowed them to operate independently. Recently, MTD has taken a more aggressive role and integrated Cub Cadet into its other lines of power equipment.

This website and forum are not affiliated with or sponsored by MTD Products Inc, which owns the CUB CADET trademarks. It is not an official MTD Products Inc, website, and MTD Products Inc, is not responsible for any of its content. The official MTD Products Inc, website can be found at: http://www.mtdproducts.com. The information and opinions expressed on this website are the responsibility of the website's owner and/or it's members, and do not represent the opinions of MTD Products Inc. IH, INTERNATIONAL HARVESTER are registered trademark of CNH America LLC

All material, images, and graphics from this site are the property of www.onlycubcadets.net. Any unauthorized use, reproductions, or duplications are prohibited unless solely expressed in writing.

Cub Cadet, Cub, Cadet, IH, MTD, Parts, Tractors, Tractor, International Harvester, Lawn, Garden, Lawn Mower, Kohler, garden tractor equipment, lawn garden tractors, antique garden tractors, garden tractor, PTO, parts, online, Original, 70, 71, 72, 73, 76, SO76, 80, 81, 86, 100, 102, 104, 105, 106, 107, 108,109, 122, 123, 124, 125, 126, 127, 128, 129, 147, 149, 169, 182, 282, 382, 482, 580, 582, 582 Special, 680, 682, 782, 782D, 784, 800, 805, 882, 982, 984, 986, 1000, 1015, 1100, 1105, 1110, 1200, 1250, 1282, 1450, 1512, 1604, 1605, 1606, 1610, 1615, 1620, 1650, 1710, 1711, 1712, 1806, 1810, 1811, 1812, 1912, 1914.