Rear end cover plate question ????

If you would like to help maintain this site & enhance it, feel free to donate whatever amount you would like to!

		Only Cub Cadets > Cub Cadets > CCC/MTD Cub Cadet built Tractors (GT)
Rear end cover plate question ????

FAQ

Calendar

Thread Tools

Display Modes

09-04-2013, 07:58 AM

cubfan

Senior Member

Join Date: Jan 2010

Location: Tennessee

Posts: 341

Rear end cover plate question ????

I am wanting to make a custom hitch/battery box/cold drink carrier (lol) for my 2072. I have never been comfortable with putting the pulling load on the two bolts on these aluminum rears. My thought is to make or get a steel cover plate weld the hitch to that and go from there. That way the load would be distributed over the entire bolt pattern and not just the two. I know its four bolts but ultimately the load goes to the first two then the bottom two. Not wanting to take chances with this aluminum rear. Whew, my question is, is the bolt pattern the same on a cast rear cover, as an aluminum rear cover. Getting a steel cast rear cover off ebay would save me quiet a bit of time if it will bolt up. I hope I haven't been too confusing.

« Previous Thread | Next Thread »

Posting Rules
You may not post new threads You may not post replies You may not post attachments You may not edit your posts BB code is On Smilies are On [IMG] code is On HTML code is Off Forum Rules

Forum Jump

All times are GMT -4. The time now is 08:52 AM.

Cub Cadet is a premium line of outdoor power equipment, established in 1961 as part of International Harvester. During the 1960s, IH initiated an entirely new line of lawn and garden equipment aimed at the owners rural homes with large yards and private gardens. There were a wide variety of Cub Cadet branded and after-market attachments available; including mowers, blades, snow blowers, front loaders, plows, carts, etc. Cub Cadet advertising at that time harped on their thorough testing by "boys - acknowledged by many as the world's worst destructive force!". Cub Cadets became known for their dependability and rugged construction.

MTD Products, Inc. of Cleveland, Ohio purchased the Cub Cadet brand from International Harvester in 1981. Cub Cadet was held as a wholly owned subsidiary for many years following this acquisition, which allowed them to operate independently. Recently, MTD has taken a more aggressive role and integrated Cub Cadet into its other lines of power equipment.

This website and forum are not affiliated with or sponsored by MTD Products Inc, which owns the CUB CADET trademarks. It is not an official MTD Products Inc, website, and MTD Products Inc, is not responsible for any of its content. The official MTD Products Inc, website can be found at: http://www.mtdproducts.com. The information and opinions expressed on this website are the responsibility of the website's owner and/or it's members, and do not represent the opinions of MTD Products Inc. IH, INTERNATIONAL HARVESTER are registered trademark of CNH America LLC

All material, images, and graphics from this site are the property of www.onlycubcadets.net. Any unauthorized use, reproductions, or duplications are prohibited unless solely expressed in writing.

Cub Cadet, Cub, Cadet, IH, MTD, Parts, Tractors, Tractor, International Harvester, Lawn, Garden, Lawn Mower, Kohler, garden tractor equipment, lawn garden tractors, antique garden tractors, garden tractor, PTO, parts, online, Original, 70, 71, 72, 73, 76, SO76, 80, 81, 86, 100, 102, 104, 105, 106, 107, 108,109, 122, 123, 124, 125, 126, 127, 128, 129, 147, 149, 169, 182, 282, 382, 482, 580, 582, 582 Special, 680, 682, 782, 782D, 784, 800, 805, 882, 982, 984, 986, 1000, 1015, 1100, 1105, 1110, 1200, 1250, 1282, 1450, 1512, 1604, 1605, 1606, 1610, 1615, 1620, 1650, 1710, 1711, 1712, 1806, 1810, 1811, 1812, 1912, 1914.