Kohler K241 crank shaft back lash

If you would like to help maintain this site & enhance it, feel free to donate whatever amount you would like to!

Attention Guest, We have turned off the forum to guest. This is due to bots attacking the site. It is still free to register.

-->

		Only Cub Cadets > Cub Cadets > Cub Cadet Engines > Kohler Engines
Kohler K241 crank shaft back lash

FAQ

Calendar

Thread Tools

Display Modes

04-28-2013, 01:37 PM

fitz1

New Member

Join Date: Mar 2013

Location: Pennsylvania

Posts: 12

Kohler K241 crank shaft back lash

Hello, I am assembling my 10 hp, I had it bored .010 over. as I was installing the crankshaft I could not seem to get an acceptable free play movement. One new bearing USA made and it is the same thickness, 905. I measured all the old parts and new, however I need .050. [three gaskets] to gain .006 free play. It is more than what came out? original gasket was .020. I did not check the free play prior to removal. I do not know if it was tight from the factory? The last engine I did only required [one gasket].030. It is the same crank, same block, same bearing measurements..I removed the bearings several times, it is very clean no signs of dirt or debris. Any help or advice would be appreciated.

« Previous Thread | Next Thread »

Posting Rules
You may not post new threads You may not post replies You may not post attachments You may not edit your posts BB code is On Smilies are On [IMG] code is On HTML code is Off Forum Rules

Forum Jump

All times are GMT -4. The time now is 06:16 AM.

Cub Cadet is a premium line of outdoor power equipment, established in 1961 as part of International Harvester. During the 1960s, IH initiated an entirely new line of lawn and garden equipment aimed at the owners rural homes with large yards and private gardens. There were a wide variety of Cub Cadet branded and after-market attachments available; including mowers, blades, snow blowers, front loaders, plows, carts, etc. Cub Cadet advertising at that time harped on their thorough testing by "boys - acknowledged by many as the world's worst destructive force!". Cub Cadets became known for their dependability and rugged construction.

MTD Products, Inc. of Cleveland, Ohio purchased the Cub Cadet brand from International Harvester in 1981. Cub Cadet was held as a wholly owned subsidiary for many years following this acquisition, which allowed them to operate independently. Recently, MTD has taken a more aggressive role and integrated Cub Cadet into its other lines of power equipment.

This website and forum are not affiliated with or sponsored by MTD Products Inc, which owns the CUB CADET trademarks. It is not an official MTD Products Inc, website, and MTD Products Inc, is not responsible for any of its content. The official MTD Products Inc, website can be found at: http://www.mtdproducts.com. The information and opinions expressed on this website are the responsibility of the website's owner and/or it's members, and do not represent the opinions of MTD Products Inc. IH, INTERNATIONAL HARVESTER are registered trademark of CNH America LLC

All material, images, and graphics from this site are the property of www.onlycubcadets.net. Any unauthorized use, reproductions, or duplications are prohibited unless solely expressed in writing.

Cub Cadet, Cub, Cadet, IH, MTD, Parts, Tractors, Tractor, International Harvester, Lawn, Garden, Lawn Mower, Kohler, garden tractor equipment, lawn garden tractors, antique garden tractors, garden tractor, PTO, parts, online, Original, 70, 71, 72, 73, 76, SO76, 80, 81, 86, 100, 102, 104, 105, 106, 107, 108,109, 122, 123, 124, 125, 126, 127, 128, 129, 147, 149, 169, 182, 282, 382, 482, 580, 582, 582 Special, 680, 682, 782, 782D, 784, 800, 805, 882, 982, 984, 986, 1000, 1015, 1100, 1105, 1110, 1200, 1250, 1282, 1450, 1512, 1604, 1605, 1606, 1610, 1615, 1620, 1650, 1710, 1711, 1712, 1806, 1810, 1811, 1812, 1912, 1914.