|
PLEASE PATRONIZE OUR SPONSORS!
|
|||||||
|
|
Thread Tools | Display Modes |
|
#1
04-08-2015, 06:23 PM
|
||||
|
||||
Spindle Roller Bearing Endplay
Hello. Today I was working on a deck that my SIL recently purchased. The bolt holding the pulley on the center spindle was loose. I snugged the bolt down and the shaft would not turn. Well we need some shims, but how many? I could not find in the manuals how much endplay the spindles should have, so I hit the web and found this on the Timken site. The info is for the old car front axles, but the dims. are right for deck spindles. I hope this helps someone besides myself.
To adjust the setting of this bearing: Step 1: Tighten the nut while turning the hub. When there is a slight bind on the bearing, the parts are seated correctly. Step 2: Back the nut off 1/6 to 1/4 of a turn or sufficiently to allow .001” to .007“ end play. Note: Failure to back off adjusting nut could cause bearing to run hot and be damaged. Wheel could lock or separate. Richard 
|
| Thread Tools | |
| Display Modes | |
|
|
Cub Cadet is a premium line of outdoor power equipment, established in 1961 as part of International Harvester. During the 1960s, IH initiated an entirely new line of lawn and garden equipment aimed at the owners rural homes with large yards and private gardens. There were a wide variety of Cub Cadet branded and after-market attachments available; including mowers, blades, snow blowers, front loaders, plows, carts, etc. Cub Cadet advertising at that time harped on their thorough testing by "boys - acknowledged by many as the world's worst destructive force!". Cub Cadets became known for their dependability and rugged construction.
MTD Products, Inc. of Cleveland, Ohio purchased the Cub Cadet brand from International Harvester in 1981. Cub Cadet was held as a wholly owned subsidiary for many years following this acquisition, which allowed them to operate independently. Recently, MTD has taken a more aggressive role and integrated Cub Cadet into its other lines of power equipment.
This website and forum are not affiliated with or sponsored by MTD Products Inc, which owns the CUB CADET trademarks. It is not an official MTD Products Inc, website, and MTD Products Inc, is not responsible for any of its content. The official MTD Products Inc, website can be found at: http://www.mtdproducts.com. The information and opinions expressed on this website are the responsibility of the website's owner and/or it's members, and do not represent the opinions of MTD Products Inc. IH, INTERNATIONAL HARVESTER are registered trademark of CNH America LLC
All material, images, and graphics from this site are the property of www.onlycubcadets.net. Any unauthorized use, reproductions, or duplications are prohibited unless solely expressed in writing.
Cub Cadet, Cub, Cadet, IH, MTD, Parts, Tractors, Tractor, International Harvester, Lawn, Garden, Lawn Mower, Kohler, garden tractor equipment, lawn garden tractors, antique garden tractors, garden tractor, PTO, parts, online, Original, 70, 71, 72, 73, 76, SO76, 80, 81, 86, 100, 102, 104, 105, 106, 107, 108,109, 122, 123, 124, 125, 126, 127, 128, 129, 147, 149, 169, 182, 282, 382, 482, 580, 582, 582 Special, 680, 682, 782, 782D, 784, 800, 805, 882, 982, 984, 986, 1000, 1015, 1100, 1105, 1110, 1200, 1250, 1282, 1450, 1512, 1604, 1605, 1606, 1610, 1615, 1620, 1650, 1710, 1711, 1712, 1806, 1810, 1811, 1812, 1912, 1914.
Threaded Mode