|
PLEASE PATRONIZE OUR SPONSORS!
|
|||||||
 |
|
|
Thread Tools | Display Modes |
|
|
|
#1
05-14-2023, 10:05 AM
|
|||
|
|||
106 trans issue
Hey guys. I'm just getting started on this adventure and could use a little insight.
Just got what I think is a decent deal. A '69 106 running with a refurbished deck, wheel weights, a new battery, along with a not running '70 147, with 3 extra decks, and 2 sets of wheels for $550 (plus $150 in fuel to get them). I do have the service manual ordered and on the way, but I'm kinda chomping at the bit to start working on them. I got the 147 running with a little work. He told me that the 106 "pops out of gear". I pulled the trans cover off and everything looks decent. While running in 1st gear, there's not much of an issue until going up hill. 2nd and 3rd only work on level or downhill ground. I don't believe its the clutch, but I could be wrong. I can see it engaging and disengaging. There is a rattle, or grinding noise then its engaged in the 2 higher gears. and the shaft between the engine and trans does spin. I wouldn't think that it would be possible to "strip" the driveshaft, but is that what is sounds like? Thanks for any help 
|
|
#3
05-14-2023, 10:38 AM
|
|||
|
|||
|
Welcome to OCC........
__________________
[B]Roland Bedell[/B] CC Models: 100, 105, 1450, 782, (2) 784, & 2072 [SIZE="4"][B][COLOR="Red"]Buy:[/COLOR][COLOR="Blue"] Made in the USA[/COLOR][/B] [/SIZE]:American Flag 1:
|
|
#4
05-14-2023, 11:23 AM
|
||||
|
||||
|
Your shifter problem is not uncommon.
When you had the shifter cover off, pay attention to the bolts (#12). They clamp the shifter forks (#14 & 18) tight on the shift rods (#13 & 17). The bolts tend to loosen and allow the forks to get out of adjustment on the rods. Most of the manuals you will need are available for free here in the Technical Library or elsewhere online.
|
|
#5
05-15-2023, 07:53 PM
|
|||
|
|||
|
OK, I pulled the cover back off of the trans. Started it up in neutral and everything spins nice and smoothly. Put it in 3d and released the clutch. It grabbed for a split second, then just noise. What I'm calling the driveshaft is spinning just fine, but it's rattling where it goes into the trans (into the hump on top). It spins and theres rattling coming from the "hump"
Any ideas where to start?
|
|
#6
05-16-2023, 07:56 AM
|
|||
|
|||
|
Removing the back cover won't tell you much.
I suspect the issue is the input shaft coupler and pins that secure it to the driveshaft. Broken spirol pins in the driveshaft coupler........ Remove the tunnel cover to access the coupler for inspection. Remove and inspect the pins and coupler and mounting holes on the driveshaft proper, repair/replace if necessary. Support the driveshaft while driving out and installing these pins to avoid damage to the bearing in the transmission. Use the proper roll pin punch Look for wallowed out holes in both parts. Therein may be the issue causing the pin(s) to shear. Be sure and use NEW spirol coiled pins and not the hardware store split ones. If you can remove both pins, you might be able to raise the shaft enough to remove the coupler. If not, the engine will have to be slid ahead in the frame so the driveshaft ass'y can be removed. https://www.cubcadet.com/en_US/conte...670a0f800d1a/y Part #21
|
|
|
|
Cub Cadet is a premium line of outdoor power equipment, established in 1961 as part of International Harvester. During the 1960s, IH initiated an entirely new line of lawn and garden equipment aimed at the owners rural homes with large yards and private gardens. There were a wide variety of Cub Cadet branded and after-market attachments available; including mowers, blades, snow blowers, front loaders, plows, carts, etc. Cub Cadet advertising at that time harped on their thorough testing by "boys - acknowledged by many as the world's worst destructive force!". Cub Cadets became known for their dependability and rugged construction.
MTD Products, Inc. of Cleveland, Ohio purchased the Cub Cadet brand from International Harvester in 1981. Cub Cadet was held as a wholly owned subsidiary for many years following this acquisition, which allowed them to operate independently. Recently, MTD has taken a more aggressive role and integrated Cub Cadet into its other lines of power equipment.
This website and forum are not affiliated with or sponsored by MTD Products Inc, which owns the CUB CADET trademarks. It is not an official MTD Products Inc, website, and MTD Products Inc, is not responsible for any of its content. The official MTD Products Inc, website can be found at: http://www.mtdproducts.com. The information and opinions expressed on this website are the responsibility of the website's owner and/or it's members, and do not represent the opinions of MTD Products Inc. IH, INTERNATIONAL HARVESTER are registered trademark of CNH America LLC
All material, images, and graphics from this site are the property of www.onlycubcadets.net. Any unauthorized use, reproductions, or duplications are prohibited unless solely expressed in writing.
Cub Cadet, Cub, Cadet, IH, MTD, Parts, Tractors, Tractor, International Harvester, Lawn, Garden, Lawn Mower, Kohler, garden tractor equipment, lawn garden tractors, antique garden tractors, garden tractor, PTO, parts, online, Original, 70, 71, 72, 73, 76, SO76, 80, 81, 86, 100, 102, 104, 105, 106, 107, 108,109, 122, 123, 124, 125, 126, 127, 128, 129, 147, 149, 169, 182, 282, 382, 482, 580, 582, 582 Special, 680, 682, 782, 782D, 784, 800, 805, 882, 982, 984, 986, 1000, 1015, 1100, 1105, 1110, 1200, 1250, 1282, 1450, 1512, 1604, 1605, 1606, 1610, 1615, 1620, 1650, 1710, 1711, 1712, 1806, 1810, 1811, 1812, 1912, 1914.
Hybrid Mode
