|
PLEASE PATRONIZE OUR SPONSORS!
|
|||||||
 |
|
|
Thread Tools | Display Modes |
|
|
|
#1
03-07-2014, 06:35 PM
|
||||
|
||||
Pulley puller
I made this funny PTO basket puller today out of an old drive shaft, some longer basket pulley set screws and a sledge hammer head. It worked fine. Alternated the puller from one screw to the other. I put the Allen head of the screws into the holes in case it broke off so I can get it out later. I may change the set screws to non hardened ones though.
Don't forget your safety glasses!!! Please comment if you please.
__________________
Up to 533 and counting... I give up updating my profile! 
|
|
#3
03-07-2014, 07:11 PM
|
||||
|
||||
I used the puller not my head!
BTW this was soaking for 2 days in PB so it kinda helped.
__________________
Up to 533 and counting... I give up updating my profile!
|
|
#5
03-07-2014, 07:52 PM
|
||||
|
||||
|
Quote:
 I like KROIL better than PB or LW. Did you leave the PTO arm in place? I could make a piece for the driveshaft to slip over the threaded collar so the basket pulley would be driven straight off. I used a different approach to get my pulley off. I made a puller and drilled the pulley for 5/16-18NC ( "F" drill ) The spacing also works for removing the flywheel.   By using two longer bolts with 1/2" sockets, it makes a great PTO bearing puller  
|
|
#6
03-07-2014, 07:53 PM
|
|||
|
|||
|
Quote:
|
|
#8
03-07-2014, 08:20 PM
|
||||
|
||||
|
Anything that Gits Er Done is a good thing, way to go Buddy!
 I would have used the fire wrench and probably cooked the engine.
__________________
2264 with 54 GT deck 1641 AKA Black Jack with a 402-E Haban Sickle bar mower JD317 dump truck BX2670 with FEL
|
|
#9
03-07-2014, 08:24 PM
|
||||
|
||||
|
Quote:
Yes it was Nick. Jeff, I would like to see if you can make a collar to fit over the part of the pulley that has the set screws, then drill 2 holes in it that would line up the the ones on the pulley, put a threaded end on the collar to fit on a real slide hammer.sorta something like that... There are different sizes of bushings on the pto baskets though,so you would have to get at least the two sizes I have seen.
__________________
Up to 533 and counting... I give up updating my profile!
|
|
#10
03-07-2014, 08:38 PM
|
||||
|
||||
|
Good thinking Lew
So.... now if we want to make one, do we just get the drive shafts from Nick?
__________________
Make the best of each day , Todd  Original's Face Lift thread.http://www.onlycubcadets.net/forum/s...ad.php?t=34439 (O) Start to Finish video.https://www.youtube.com/watch?v=GAoUNNiLwKs Wheel Around videohttps://www.youtube.com/watch?v=XUL-m6Bramk They can't all be turn key! 
|
|
|
|
Cub Cadet is a premium line of outdoor power equipment, established in 1961 as part of International Harvester. During the 1960s, IH initiated an entirely new line of lawn and garden equipment aimed at the owners rural homes with large yards and private gardens. There were a wide variety of Cub Cadet branded and after-market attachments available; including mowers, blades, snow blowers, front loaders, plows, carts, etc. Cub Cadet advertising at that time harped on their thorough testing by "boys - acknowledged by many as the world's worst destructive force!". Cub Cadets became known for their dependability and rugged construction.
MTD Products, Inc. of Cleveland, Ohio purchased the Cub Cadet brand from International Harvester in 1981. Cub Cadet was held as a wholly owned subsidiary for many years following this acquisition, which allowed them to operate independently. Recently, MTD has taken a more aggressive role and integrated Cub Cadet into its other lines of power equipment.
This website and forum are not affiliated with or sponsored by MTD Products Inc, which owns the CUB CADET trademarks. It is not an official MTD Products Inc, website, and MTD Products Inc, is not responsible for any of its content. The official MTD Products Inc, website can be found at: http://www.mtdproducts.com. The information and opinions expressed on this website are the responsibility of the website's owner and/or it's members, and do not represent the opinions of MTD Products Inc. IH, INTERNATIONAL HARVESTER are registered trademark of CNH America LLC
All material, images, and graphics from this site are the property of www.onlycubcadets.net. Any unauthorized use, reproductions, or duplications are prohibited unless solely expressed in writing.
Cub Cadet, Cub, Cadet, IH, MTD, Parts, Tractors, Tractor, International Harvester, Lawn, Garden, Lawn Mower, Kohler, garden tractor equipment, lawn garden tractors, antique garden tractors, garden tractor, PTO, parts, online, Original, 70, 71, 72, 73, 76, SO76, 80, 81, 86, 100, 102, 104, 105, 106, 107, 108,109, 122, 123, 124, 125, 126, 127, 128, 129, 147, 149, 169, 182, 282, 382, 482, 580, 582, 582 Special, 680, 682, 782, 782D, 784, 800, 805, 882, 982, 984, 986, 1000, 1015, 1100, 1105, 1110, 1200, 1250, 1282, 1450, 1512, 1604, 1605, 1606, 1610, 1615, 1620, 1650, 1710, 1711, 1712, 1806, 1810, 1811, 1812, 1912, 1914.
Hybrid Mode
