Only Cub Cadets

PLEASE PATRONIZE OUR SPONSORS!

CC Specialties R. F. Houtz and Sons Jeff in Pa.

P&K Cub Cadet Machtech Direct

Cub Cadet Parts & Service


If you would like to help maintain this site & enhance it, feel free to donate whatever amount you would like to!




Go Back   Only Cub Cadets > Resources > Restoration Tips

Notices

Reply
 
Thread Tools Display Modes
  #1  
Old 04-26-2013, 08:16 AM
Cjbdvm04 Cjbdvm04 is offline
Member
 
Join Date: Jun 2011
Location: Oakdale, CT
Posts: 87
Default Engine paint

I recently got my k301 block back from the machine shop. Block was ball peened and cleaned up. Looked great!!!! Amazing to look at that bare cast iron. I decided to use Rustoleum High Heat Ultra BBQ paint on the block. Rated at 1200 degrees. This stuff is incredible. I comes in flat or high-sheen semi. I chose the latter. Great spray, great coverage and amazing drying time. Within 2 minutes, the paint was dry enought that a thumb firmly pressed into the surface didn't leave a mark. Waited 10 minutes and recoated. Repeated this until I had 6 coats on it. Later in the afternoon (about 5 hrs later) I put it in my oven set at 170 degrees for 4 hrs. I know some people will comment that that is too soon to cook the paint. Not even a single bubble. And the surface is so tough that a fingernail can't even come close to scratching it. The only problem I had was with the oil pan. I ordered a used cast iron from fleabay. It came with rust, grease, chipped paint. Prepped it as best as I could; evaporust, degreaser, scotch bright. Then painted as I did with the block. While assembling the engine, I noticed some of the areas on the pan were flaking off. I think I may take the pan and re-prep it then prime it with rust inhibiting primer and try painting again.
Reply With Quote
  #2  
Old 04-27-2013, 08:40 PM
CadetTY's Avatar
CadetTY CadetTY is offline
Senior Member
 
Join Date: Nov 2012
Location: peru new york
Posts: 283
Default

What is ball peened? What does it do to the block?
__________________
882 diesel, x3 ih 582, 73 124, x2 82 seriers pullers, 1686 16hp puller
Reply With Quote
  #3  
Old 04-27-2013, 09:39 PM
Cjbdvm04 Cjbdvm04 is offline
Member
 
Join Date: Jun 2011
Location: Oakdale, CT
Posts: 87
Default

Ball preening is like sandblasting except the media is tiny metallic spheres rather than sand.
Reply With Quote
  #4  
Old 06-06-2013, 11:24 AM
WinterHawk77 WinterHawk77 is offline
New Member
 
Join Date: May 2012
Location: Rhode Island
Posts: 15
Default

Also called shot peening. It closes the metal pores as opposed to sand that opens the pores. Much different results.
Reply With Quote
Reply


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 12:56 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2025, vBulletin Solutions Inc.

Cub Cadet is a premium line of outdoor power equipment, established in 1961 as part of International Harvester. During the 1960s, IH initiated an entirely new line of lawn and garden equipment aimed at the owners rural homes with large yards and private gardens. There were a wide variety of Cub Cadet branded and after-market attachments available; including mowers, blades, snow blowers, front loaders, plows, carts, etc. Cub Cadet advertising at that time harped on their thorough testing by "boys - acknowledged by many as the world's worst destructive force!". Cub Cadets became known for their dependability and rugged construction.

MTD Products, Inc. of Cleveland, Ohio purchased the Cub Cadet brand from International Harvester in 1981. Cub Cadet was held as a wholly owned subsidiary for many years following this acquisition, which allowed them to operate independently. Recently, MTD has taken a more aggressive role and integrated Cub Cadet into its other lines of power equipment.

This website and forum are not affiliated with or sponsored by MTD Products Inc, which owns the CUB CADET trademarks. It is not an official MTD Products Inc, website, and MTD Products Inc, is not responsible for any of its content. The official MTD Products Inc, website can be found at: http://www.mtdproducts.com. The information and opinions expressed on this website are the responsibility of the website's owner and/or it's members, and do not represent the opinions of MTD Products Inc. IH, INTERNATIONAL HARVESTER are registered trademark of CNH America LLC

All material, images, and graphics from this site are the property of www.onlycubcadets.net. Any unauthorized use, reproductions, or duplications are prohibited unless solely expressed in writing.

Cub Cadet, Cub, Cadet, IH, MTD, Parts, Tractors, Tractor, International Harvester, Lawn, Garden, Lawn Mower, Kohler, garden tractor equipment, lawn garden tractors, antique garden tractors, garden tractor, PTO, parts, online, Original, 70, 71, 72, 73, 76, SO76, 80, 81, 86, 100, 102, 104, 105, 106, 107, 108,109, 122, 123, 124, 125, 126, 127, 128, 129, 147, 149, 169, 182, 282, 382, 482, 580, 582, 582 Special, 680, 682, 782, 782D, 784, 800, 805, 882, 982, 984, 986, 1000, 1015, 1100, 1105, 1110, 1200, 1250, 1282, 1450, 1512, 1604, 1605, 1606, 1610, 1615, 1620, 1650, 1710, 1711, 1712, 1806, 1810, 1811, 1812, 1912, 1914.