Only Cub Cadets

PLEASE PATRONIZE OUR SPONSORS!

CC Specialties R. F. Houtz and Sons Jeff in Pa.

P&K Cub Cadet Machtech Direct

Cub Cadet Parts & Service


If you would like to help maintain this site & enhance it, feel free to donate whatever amount you would like to!




Go Back   Only Cub Cadets > Cub Cadets > CCC/MTD Cub Cadet built Tractors (GT)

Notices

Reply
 
Thread Tools Display Modes
  #1  
Old 03-29-2016, 03:09 PM
veegee2 veegee2 is offline
New Member
 
Join Date: Nov 2011
Location: MD
Posts: 10
Default When did Cub Cadet start using thread sealer on bolts?

I bought a used 3000 series Cub Cadet rear Transmission/Differential assembly (Part # 618-3235) and when I examined the inside of it the four 3/8-24 x 2.25 bolts (part # 710-1254) had loosened and caused damage to the 54 tooth bevel gear (part # 717-3449). When I ordered new parts for it I noticed that the replacement bolts now have a sealer (Loctite?) on the threads that lock the bolts in place.

Does anyone know if these locking bolts were used on the assembly line or are they just used for repair work?

If they were used on the assembly line does anyone know when Cub Cadet started using bolts with this sealer? I also have a Cub Cadet GT3200 that I am very concerned about because of this type of failure. The s/n of it is 1F146G10029 and the DOM is 6/2006.

Thanks
Reply With Quote
  #2  
Old 03-29-2016, 03:28 PM
J-Mech J-Mech is offline
Banned
 
Join Date: Apr 2013
Location: Oblong, Illinois
Posts: 17,594
Default

They used thread sealer on the trans housing bolts all the way back to the beginning of CCC. The first aluminum housings they built used the sealer.

I'm fairly certain it is sealer, and not lock tite. It seals, not locks.

The failure you speak of is a common issue the the 3K series machines. You have to keep and eye on it.
Reply With Quote
  #3  
Old 03-30-2016, 08:28 AM
veegee2 veegee2 is offline
New Member
 
Join Date: Nov 2011
Location: MD
Posts: 10
Default When did Cub Cadet start using thread locking sealer on internal differential bolts?

How am I supposed to “keep an eye on it” when it is inside of the cast iron housing? Yesterday I did drain the fluid and inserted a bore scope through the fill hole. The best I could see using this method were the head of one of the 3/8-24 x 2.25 bolts (part # 710-1254) and a portion of the face of the 54 tooth bevel gear (part # 717-3449). The bolt was in the proper position and the face of the bevel gear showed no damage. Also, the drained fluid had no metal filings so this was also a good indicator that nothing was rubbing so far.

I also have a Cub Cadet Model 3240 (Year 2001 40th Anniversary Edition) and although I have not yet dismantled it the drive system quit working and I suspect that it was caused by the 3/8-24 x 2.25 bolt (part # 710-1254) failure so I don’t think that they were using bolts with thread locking sealer back that far.

What I really would like to know is does my GT3200 have thread locking sealer on the 3/8-24 x 2.25 bolts (part # 710-1254) from the factory?
Reply With Quote
  #4  
Old 03-30-2016, 10:24 AM
J-Mech J-Mech is offline
Banned
 
Join Date: Apr 2013
Location: Oblong, Illinois
Posts: 17,594
Default

They didn't use thread lock, they used sealer. Not the same thing. So I guess the answer is no, they didn't.
Reply With Quote
Reply


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 05:37 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2025, vBulletin Solutions Inc.

Cub Cadet is a premium line of outdoor power equipment, established in 1961 as part of International Harvester. During the 1960s, IH initiated an entirely new line of lawn and garden equipment aimed at the owners rural homes with large yards and private gardens. There were a wide variety of Cub Cadet branded and after-market attachments available; including mowers, blades, snow blowers, front loaders, plows, carts, etc. Cub Cadet advertising at that time harped on their thorough testing by "boys - acknowledged by many as the world's worst destructive force!". Cub Cadets became known for their dependability and rugged construction.

MTD Products, Inc. of Cleveland, Ohio purchased the Cub Cadet brand from International Harvester in 1981. Cub Cadet was held as a wholly owned subsidiary for many years following this acquisition, which allowed them to operate independently. Recently, MTD has taken a more aggressive role and integrated Cub Cadet into its other lines of power equipment.

This website and forum are not affiliated with or sponsored by MTD Products Inc, which owns the CUB CADET trademarks. It is not an official MTD Products Inc, website, and MTD Products Inc, is not responsible for any of its content. The official MTD Products Inc, website can be found at: http://www.mtdproducts.com. The information and opinions expressed on this website are the responsibility of the website's owner and/or it's members, and do not represent the opinions of MTD Products Inc. IH, INTERNATIONAL HARVESTER are registered trademark of CNH America LLC

All material, images, and graphics from this site are the property of www.onlycubcadets.net. Any unauthorized use, reproductions, or duplications are prohibited unless solely expressed in writing.

Cub Cadet, Cub, Cadet, IH, MTD, Parts, Tractors, Tractor, International Harvester, Lawn, Garden, Lawn Mower, Kohler, garden tractor equipment, lawn garden tractors, antique garden tractors, garden tractor, PTO, parts, online, Original, 70, 71, 72, 73, 76, SO76, 80, 81, 86, 100, 102, 104, 105, 106, 107, 108,109, 122, 123, 124, 125, 126, 127, 128, 129, 147, 149, 169, 182, 282, 382, 482, 580, 582, 582 Special, 680, 682, 782, 782D, 784, 800, 805, 882, 982, 984, 986, 1000, 1015, 1100, 1105, 1110, 1200, 1250, 1282, 1450, 1512, 1604, 1605, 1606, 1610, 1615, 1620, 1650, 1710, 1711, 1712, 1806, 1810, 1811, 1812, 1912, 1914.