|
PLEASE PATRONIZE OUR SPONSORS!
|
|||||||
 |
|
|
Thread Tools
|
Display Modes
|
|
#1
06-23-2015, 11:27 AM
|
|||
|
|||
Torque Specs
I have a Quiet Line 1450.
I am replacing the aluminum oil pan with a cast iron one. New gasket. I'm also replacing all of the rubber ISO mounts. I need to know the torque specifications for the bolts that hold the oil pan to the engine and the bolts that connect the ISO rails to the oil pan. Does anyone have the factory specifications for these? 
|
|
#2
06-23-2015, 11:38 AM
|
|||
|
|||
The spec's for the Oil Pan is in the Service Manual. There is NO specs for the ISO mounts.
__________________
[B]Roland Bedell[/B] CC Models: 100, 105, 1450, 782, (2) 784, & 2072 [SIZE="4"][B][COLOR="Red"]Buy:[/COLOR][COLOR="Blue"] Made in the USA[/COLOR][/B] [/SIZE]:American Flag 1:
|
|
#4
06-23-2015, 01:35 PM
|
||||
|
||||
|
Quote:
__________________
Tim Pap's 100 Restored 108 1211 Dual Stick 1050 Pap's 100 restoration thread - http://onlycubcadets.net/forum/showthread.php?t=47965
|
|
#5
06-23-2015, 02:14 PM
|
|||
|
|||
|
Anybody care to throw out a number? I looked in the service manual that I have, but it just gives general torque specs based on bolt size and material. According to it bolts of this size going into cast iron ought to be between 33-37 foot-pounds for Grade 5 and 43-47 foot-pounds for grade 8. Do these numbers qualify as "tight"? I understand that I want them as tight as possible and I'm using Locktight on the threads because they tend to vibrate loose. I'm also using washers and lock washers on the rail bolts, but I don't want to crack the castings.
The service manual I have says to refer to the "Blue Ribbon Service Manual #GSS-1465." I assume this is a manual devoted to engine overhauling. Does anyone have a copy?
|
|
#7
06-23-2015, 02:41 PM
|
||||
|
||||
|
Quote:
__________________
Up to 530 and counting... I give up updating my profile!
|
|
#9
06-23-2015, 03:11 PM
|
||||
|
||||
|
Just as a FYI, make sure you don't use too long of bolts connecting the iso rails to the pan, especially if using an aluminum pan ( your not) because you will crack into the pan boss and it will leak.
Seen it before. Do chase the threads in the pan with a bottom tap. The bolts should be just long enough to bottom out, going through the rail without a lock washer ( finger tight) then add the lock washer on final assy. That way you are sure they are not too long, but long enough to get max depth/strength. Clear as mud? 
|
|
|
|
Cub Cadet is a premium line of outdoor power equipment, established in 1961 as part of International Harvester. During the 1960s, IH initiated an entirely new line of lawn and garden equipment aimed at the owners rural homes with large yards and private gardens. There were a wide variety of Cub Cadet branded and after-market attachments available; including mowers, blades, snow blowers, front loaders, plows, carts, etc. Cub Cadet advertising at that time harped on their thorough testing by "boys - acknowledged by many as the world's worst destructive force!". Cub Cadets became known for their dependability and rugged construction.
MTD Products, Inc. of Cleveland, Ohio purchased the Cub Cadet brand from International Harvester in 1981. Cub Cadet was held as a wholly owned subsidiary for many years following this acquisition, which allowed them to operate independently. Recently, MTD has taken a more aggressive role and integrated Cub Cadet into its other lines of power equipment.
This website and forum are not affiliated with or sponsored by MTD Products Inc, which owns the CUB CADET trademarks. It is not an official MTD Products Inc, website, and MTD Products Inc, is not responsible for any of its content. The official MTD Products Inc, website can be found at: http://www.mtdproducts.com. The information and opinions expressed on this website are the responsibility of the website's owner and/or it's members, and do not represent the opinions of MTD Products Inc. IH, INTERNATIONAL HARVESTER are registered trademark of CNH America LLC
All material, images, and graphics from this site are the property of www.onlycubcadets.net. Any unauthorized use, reproductions, or duplications are prohibited unless solely expressed in writing.
Cub Cadet, Cub, Cadet, IH, MTD, Parts, Tractors, Tractor, International Harvester, Lawn, Garden, Lawn Mower, Kohler, garden tractor equipment, lawn garden tractors, antique garden tractors, garden tractor, PTO, parts, online, Original, 70, 71, 72, 73, 76, SO76, 80, 81, 86, 100, 102, 104, 105, 106, 107, 108,109, 122, 123, 124, 125, 126, 127, 128, 129, 147, 149, 169, 182, 282, 382, 482, 580, 582, 582 Special, 680, 682, 782, 782D, 784, 800, 805, 882, 982, 984, 986, 1000, 1015, 1100, 1105, 1110, 1200, 1250, 1282, 1450, 1512, 1604, 1605, 1606, 1610, 1615, 1620, 1650, 1710, 1711, 1712, 1806, 1810, 1811, 1812, 1912, 1914.
Linear Mode
