|
PLEASE PATRONIZE OUR SPONSORS!
|
|||||||
 |
|
|
Thread Tools | Display Modes |
|
#1
11-17-2009, 11:34 PM
|
||||
|
||||
Front wheel bearings and spindles
Ok, so I was looking over my 105 and notice the right front tire is toed out, way out. I jack the front end up to see that it is actually rubbing on the steering or the frame. So I pull the wheel and the bearing has slid out of the wheel a lot. So is this two bearings? It looks like one piece, brass maybe with a grease zerk. For know can I tap this back into the wheel and just monitor it?
__________________
Mike 1968 CC 105 "Chug a lug a luggin' 5 miles an hour on my International Harvester" "Don't forget that ignition key  !!"
|
|
#2
11-18-2009, 12:09 AM
|
|||
|
|||
|
Sounds like a narrow wheel like from a 70 or 100.
Unless something is terribly worn or missing, once the bolt is snuged up it should all be held in place. I think I need to see some pictures of this wheel and problem. I'm not sure but I don't know that the narrow wheels were an option on the 105's. Someone please correct me if I'm wrong about this. I guess someone could have put an old style bushing and grease zirk in a 105 wheel. Pictures would be most helpful...
|
|
#3
11-18-2009, 12:23 AM
|
||||
|
||||
|
Ok, I will get pics tomorrow for reference. I don't know how the rims could be narrow. The front tires look like big floatation type tires. But there is definitely a grease zerk on both front rims.
__________________
Mike 1968 CC 105 "Chug a lug a luggin' 5 miles an hour on my International Harvester" "Don't forget that ignition key !!"
|
|
#4
11-18-2009, 02:45 AM
|
|||
|
|||
|
Thanks Bill,
Didn't know how long they used the narrow wheels. Didn't some of the early 70/100 series tractors use 3/4" bushings with grease zirks too? Or am I just goofy?
|
|
#5
11-18-2009, 07:49 PM
|
||||
|
||||
|
Ok, I took some pics. The rims seem like they are 6 inches wide? Would that be right?
__________________
Mike 1968 CC 105 "Chug a lug a luggin' 5 miles an hour on my International Harvester" "Don't forget that ignition key !!"
|
|
#8
11-18-2009, 09:18 PM
|
|||
|
|||
|
That's the messed upest thing I think I ever did see.
It almost looks like someone drove a huge bronze bushing into the wheel where the bearings are supposed to be... Does that thing come out of there??? Is the other wheel the same way?
|
|
#9
11-18-2009, 10:44 PM
|
||||
|
||||
|
Yes they will come out. The one is halfway out already. How do I know if the rims are ok?
__________________
Mike 1968 CC 105 "Chug a lug a luggin' 5 miles an hour on my International Harvester" "Don't forget that ignition key !!"
|
|
#10
11-19-2009, 09:23 AM
|
|||
|
|||
|
I'm not sure what the os dimension of the bearing is but I'm thinking it is 1 3/8"
The only way I would have to check them is to get a bearing and try it in the holes to check and see how well it fits. It's impossible to tell what the PO had on his mind when he "fixed" the wheels before, he may have not wanted to spend the money for new bearings and had that material laying around and the means to make it "work", or the holes in the wheels could be messed up and this is what he did to get him by, or any number of other things. Point being, don't be surprised if the holes in the wheels are "wollered" out and the right bearings don't fit any more. Not saying that is the case, just something to keep in mind. Sorry I can't be more help. Maybe someone else will have some better ideas. Good luck
|
|
|
|
Cub Cadet is a premium line of outdoor power equipment, established in 1961 as part of International Harvester. During the 1960s, IH initiated an entirely new line of lawn and garden equipment aimed at the owners rural homes with large yards and private gardens. There were a wide variety of Cub Cadet branded and after-market attachments available; including mowers, blades, snow blowers, front loaders, plows, carts, etc. Cub Cadet advertising at that time harped on their thorough testing by "boys - acknowledged by many as the world's worst destructive force!". Cub Cadets became known for their dependability and rugged construction.
MTD Products, Inc. of Cleveland, Ohio purchased the Cub Cadet brand from International Harvester in 1981. Cub Cadet was held as a wholly owned subsidiary for many years following this acquisition, which allowed them to operate independently. Recently, MTD has taken a more aggressive role and integrated Cub Cadet into its other lines of power equipment.
This website and forum are not affiliated with or sponsored by MTD Products Inc, which owns the CUB CADET trademarks. It is not an official MTD Products Inc, website, and MTD Products Inc, is not responsible for any of its content. The official MTD Products Inc, website can be found at: http://www.mtdproducts.com. The information and opinions expressed on this website are the responsibility of the website's owner and/or it's members, and do not represent the opinions of MTD Products Inc. IH, INTERNATIONAL HARVESTER are registered trademark of CNH America LLC
All material, images, and graphics from this site are the property of www.onlycubcadets.net. Any unauthorized use, reproductions, or duplications are prohibited unless solely expressed in writing.
Cub Cadet, Cub, Cadet, IH, MTD, Parts, Tractors, Tractor, International Harvester, Lawn, Garden, Lawn Mower, Kohler, garden tractor equipment, lawn garden tractors, antique garden tractors, garden tractor, PTO, parts, online, Original, 70, 71, 72, 73, 76, SO76, 80, 81, 86, 100, 102, 104, 105, 106, 107, 108,109, 122, 123, 124, 125, 126, 127, 128, 129, 147, 149, 169, 182, 282, 382, 482, 580, 582, 582 Special, 680, 682, 782, 782D, 784, 800, 805, 882, 982, 984, 986, 1000, 1015, 1100, 1105, 1110, 1200, 1250, 1282, 1450, 1512, 1604, 1605, 1606, 1610, 1615, 1620, 1650, 1710, 1711, 1712, 1806, 1810, 1811, 1812, 1912, 1914.
Linear Mode
