![]() |
PLEASE PATRONIZE OUR SPONSORS!
|
![]() |
|
Thread Tools | Display Modes |
#1
|
||||
|
||||
![]()
I am going to fill the tires on my 1211 with windshield washer fluid. I would like to here how some of you have gone about doing this.
__________________
Sold everything but one. 1211-snow pusher, cab ,54 inch plow, loaded tires (all 4) Gilson wheel weights, X-trac fronts- soon to have power steering and dual hydraulics |
#2
|
||||
|
||||
![]()
I used a rather large (6" or so) PVC pipe with a cleanout plug on one end and a cap on the other, with the cap drilled for a barb fitting for some clear hose to go to the valve stem. I put a tire valve in the cleanout plug, and applied about 10 psi to this with a gallon of fluid it. Works pretty good, you just have to burp the tire once in awhile.
Don't forget the tubes unless you have Tru-powers or something similarly stiff with a thick bead that can't be knocked off. |
#3
|
||||
|
||||
![]()
Joe, break the bead on one side and pore it in then put the air back in it. They also sell a valve at TSC for 10 bucks that you put on the stem and hook a hose to it and fill it through the stem, and the valve lets the air out. But it take quite a while to do it that way.
__________________
2013 cub cadet GTX 2100 w/IH weights 1984 cub cadet 1282 w/#2 cart, plow, IH weights 1970 IH cub cadet 73 w/fenders Haban 402d sickle bar 1966 IH cub cadet 102x2 1966 IH cub cadet 71 pull start w/Fenders IH sweeper, Brinly Gard N Cart 1965 IH cub cadet 100 w/Fenders hydro lift Brinly Gard N Cart, 3 point sleeve hitch Brinly plow sleeve hitch blade #1 cart 1965 IH cub cadet 70 w/fenders and snow plow 1961 IH Cub Cadet Original #3646 w/fenders 3 point, IH rear blade, non trip snow plow |
#4
|
||||
|
||||
![]()
MATT,
It is going the stock turf tires, and they have tubes. JR, I picked up the valve from TSC. Just not sure how to effectively use the garden hose thread side of it. I may take it to Home Depot tomorrow and see what kind of cluster of fittings I can come up with to adapt it to a container I have laying around here.
__________________
Sold everything but one. 1211-snow pusher, cab ,54 inch plow, loaded tires (all 4) Gilson wheel weights, X-trac fronts- soon to have power steering and dual hydraulics |
#5
|
||||
|
||||
![]()
Probably less expensive to get a drill powered cheapo pump @ the hwd store and use the garden hose fittings.
Automatic washer hoses work well and always somebody throwing them away with an old washer. do a search here, lots of posts on the subject. |
#6
|
||||
|
||||
![]()
jbollis
This is the setup i use for mine. Got the valve that threads on the valve stem at TSC. The little pump came from the hardware store (need a drill to power it) I fill a 5 gallon bucket with washer fluid and use a short hose from the washing machine from the bucket to the pump, and from the pump to the tire with a short garden hose. ![]() ![]() ![]() I have used this setup on 5 sets of ags of my own, plus filled a few sets for others. |
#7
|
||||
|
||||
![]()
I got it now, thanks guys. Hopefully in the next couple days I will get to it.
__________________
Sold everything but one. 1211-snow pusher, cab ,54 inch plow, loaded tires (all 4) Gilson wheel weights, X-trac fronts- soon to have power steering and dual hydraulics |
#8
|
||||
|
||||
![]()
Diz, Your way is how I will do mine when the time comes!!
About a month and a half ago Menards had washer fluid on sale for $.89/gal IIRC. It didn't even cross my mind to stock up! ![]()
__________________
Dale 147-Restored___________________882 Diesel Hydro lift (not installed)___________44" Deck 48" Deck_______________________QA-42a/b Snowthrower Rear lift ________________________XMW cat-0 rear lift Model 2 tiller____________________12" cat-0 Brinly plow |
#9
|
||||
|
||||
![]()
i know for putting in green slim or other form of sealent in tires i am not the most patient person and am to lazy to squeeze the bottle, i just put the filler tude on the valve stem and at the bottle i poke a small hole in the bottem and give it a shot through a blow gun.
the same can be done with gallon size jugs or even larger ones if you have, just like matt says you have to back off every so often to allow the air in the tire to back out of the tire. i am alll about fast cheap and easy here. you just need to line up a filler tube and adapt it to the jug lid and if you want to refill it just duct tape the hole shut, oh and do not try to put like 100psi to the container or you may wind up covered with fluid from a jug that blows up. 5-10 psi is pleanty |
#10
|
||||
|
||||
![]()
Yamaguy
I know what you mean, I have been trying to stock up when i see it on sale. |
![]() |
|
|
Cub Cadet is a premium line of outdoor power equipment, established in 1961 as part of International Harvester. During the 1960s, IH initiated an entirely new line of lawn and garden equipment aimed at the owners rural homes with large yards and private gardens. There were a wide variety of Cub Cadet branded and after-market attachments available; including mowers, blades, snow blowers, front loaders, plows, carts, etc. Cub Cadet advertising at that time harped on their thorough testing by "boys - acknowledged by many as the world's worst destructive force!". Cub Cadets became known for their dependability and rugged construction.
MTD Products, Inc. of Cleveland, Ohio purchased the Cub Cadet brand from International Harvester in 1981. Cub Cadet was held as a wholly owned subsidiary for many years following this acquisition, which allowed them to operate independently. Recently, MTD has taken a more aggressive role and integrated Cub Cadet into its other lines of power equipment.
This website and forum are not affiliated with or sponsored by MTD Products Inc, which owns the CUB CADET trademarks. It is not an official MTD Products Inc, website, and MTD Products Inc, is not responsible for any of its content. The official MTD Products Inc, website can be found at: http://www.mtdproducts.com. The information and opinions expressed on this website are the responsibility of the website's owner and/or it's members, and do not represent the opinions of MTD Products Inc. IH, INTERNATIONAL HARVESTER are registered trademark of CNH America LLC
All material, images, and graphics from this site are the property of www.onlycubcadets.net. Any unauthorized use, reproductions, or duplications are prohibited unless solely expressed in writing.
Cub Cadet, Cub, Cadet, IH, MTD, Parts, Tractors, Tractor, International Harvester, Lawn, Garden, Lawn Mower, Kohler, garden tractor equipment, lawn garden tractors, antique garden tractors, garden tractor, PTO, parts, online, Original, 70, 71, 72, 73, 76, SO76, 80, 81, 86, 100, 102, 104, 105, 106, 107, 108,109, 122, 123, 124, 125, 126, 127, 128, 129, 147, 149, 169, 182, 282, 382, 482, 580, 582, 582 Special, 680, 682, 782, 782D, 784, 800, 805, 882, 982, 984, 986, 1000, 1015, 1100, 1105, 1110, 1200, 1250, 1282, 1450, 1512, 1604, 1605, 1606, 1610, 1615, 1620, 1650, 1710, 1711, 1712, 1806, 1810, 1811, 1812, 1912, 1914.