Ten characters minimum required?
Don't mind me.
So this list represents some of the items that I have purchased for the repair/upgrade of my International Cub Cadet 1200. I know many of these parts are available through various suppliers. I am not advocating one over the other. I think it's important to support the people that support this site. So, in the "for what it's worth" column...
Ace Hardware
Assorted fasteners
Paint
Thread locker
Amazon
Air filter K & N (part # E-4655)
Carlisle Turf Master 16 x 6.5 – 8 front tires
condensor Primeline (part # 7-01338)
Grote tail lights (part # 47732)
Metal valve stems
Points Kohler (part # 47 150 03-S)
Rear work light
Spark plug Champion H8-C
Starter relay ( part # 725-3001/925-3001 )
Hydro filter Stens #120-265
http://www.ccspecialties.org/
axle tube outer bearing (part # 941-0363)
axle tube seal (part # 921-0187)
carb rebuild kit (part # 25 757 02-S)
clutch throwout bearing (part # 941 - 3056)
Deck; spindle ST-745 spindle (part # 741-3001)
spindle housing cap (part # 703-0115-0499)
spindle housing (part # 903-0117)
OEM New Style CUB CADET Quiet Line Muffler (part # 951-3029)
Oil pan gasket (part # 235353-S)
PTO switch (part # 925-3022/725-3022)
rear end cover plate gasket (part # 350837-R3)
spark plug grommet, Kohler (part # 47 313 01-S)
spring assist (part # PN/ IH-548380-R91)
thermal isolation gasket (part # 47-049-01)
throttle shaft bushing (part # 25-158-02-S)
http://www.cubclassics.com/pulling.html
blue spring
flex coupling disc page 4 on Cub Cadet parts, part # 722-3000, Yea, it's A RAG joint!
teaser spring part #932 3017
ball bushing part #941-3004
Ebay
Kohler Governor Gear Kit A-235743-S
http://www.jackssmallengines.com/
Camshaft shim .005" (part # 275066-S)
Camshaft shim .01" (part # 275067-S)
Governor gear kit (part # A235743S)
Governor shaft bushing (part # 23576)
Governor shaft (part # KH-A-235256-S)
It should be noted that without our sponsors like
Mark Hellrung, this site might not exist. Mark supplies a wide variety of new Cub Cadet parts, he reproduces no longer available Cub Cadet parts, he is a custom metal fabricator and provides machine services. Mark's continued support of us through his daily input on this site deserves a "check Mark first",
here, and
here, for any items that are needed for your project.
http://www.mcmaster.com/#
5/16” x 1 ΒΌ” coiled spring pins for clutch rebuild #91598A526
Vinyl door edge for back edge of Quietline hood # 8451A47
Heim joints;
Steering: (4)
3/8"-24 Internal Thread-Right Hand Shank
# 4444T931
Hydro Control Linkage: (1)
5/16"-24 Internal Thread-Left Hand Shank
# 4444T922
Hydro Control Linkage: (1)
5/16"-24 Internal Thread-Right Hand Shank
# 4444T921
Clamp on shaft collars for clutch rebuild #6436K15
Spring Steel Round Shim to set camshaft end play, 0.005" Thick, 1/2" ID, 3/4" OD # 90482A125
Brake pad relining material, 3/16" x 3" #6175K819
Screw in type, stainless steel grease fittings, 1/4" - 28 SAE-LT Male #1293K21
4140 5/8" Alloy steel rod for drive shafts (chrome-moly steel) #8927K98
http://midwestsupercub.net/MWSC2015.pdf
Clutch friction disc, Kevlar/fiberglass item # KD
Cedar Rapids tire
4 bolt on 4"front rims
Napa
5 gallon bucket of hytran equivalent (meets or exceeds International B-6 Specification)
Northern Tool
4 bolt wheel hub
1" weld on spindle
http://www.redoyourhorse.com/kohler-...-plate-decals/
KOHLER ENGINE SPEC PLATE DECALS
Steiner Tractor, wheel weights
https://www.steinertractor.com/IHS331-wheel-weight-set
http://www.tirechain.com/23X10.50X12.htm
Zach Kerber Machine
6 pin driver
Blue Spring
Drive shaft
head gasket, stock, 10 - 14 HP (part # KH-47-041-15-S)
Solid engine mounts
Cross Reference Cub Cadet to NAPA;
http://www.onlycubcadets.net/forum/s...ad.php?t=36314
Hey, if you have any part numbers that you know will work with the Quietlines that would be helpful to add here, don't hesitate to send me a PM, thanks.