Only Cub Cadets

Only Cub Cadets (https://www.onlycubcadets.net/forum/index.php)
-   Cub Cadet Rear Engine Rider & ZTR (RER) (https://www.onlycubcadets.net/forum/forumdisplay.php?f=43)
-   -   CC30 Small Bolt fell off...help identify? (https://www.onlycubcadets.net/forum/showthread.php?t=53009)

Trooper11040 08-05-2018 12:25 PM

CC30 Small Bolt fell off...help identify?
 
I was cutting my grass this past week. I pulled into the garage and noticed this small bolt lying under the tractor. It’s a smooth shaft bolt with little slots on the end that appear to be where maybe a leaf spring would sit. I can’t for the life of me find out where it came from. Photo attached. If anyone knows, please let me know!! Thank you!!

https://thumb.ibb.co/hgeXFe/4_C80_AF...C95_DA4_AC.jpg

J-Mech 08-05-2018 02:03 PM

You want us to tell you where that bolt came from? We're good, but not that good. What is a Cub Cadet 30 anyway?

Trooper11040 08-05-2018 02:21 PM

Some guys just know lol. It’s the small 30” rear motor. I love my little mower lol

https://thumb.ibb.co/mb56rK/C86273_D...35_DF35_A9.jpg

J-Mech 08-05-2018 02:29 PM

Oh, yeah I've seen those.

Hard to say where that may have fell out of. You will know eventually.

cooperino 08-05-2018 02:34 PM

Is there a hole through the smaller end of it? Looks like some kind of pin maybe off the deck or something.

DoubleO7 08-05-2018 04:50 PM

What diameter and length is the pin (a bolt has threads)?
Does the head have a slot, phillips, hex in it?

If it was on the floor, maybe it came from something else and not the motor.

Obviously it is not needed, lol.


Yet

Chad126 08-27-2018 01:24 PM

Just went through the entire parts list for this machine. Can't find anything that resembles this IF it is in fact a pin. Can't tell if the end of it is threaded. If it is a pin, and does not have any threads on the very end, I do not believe this came from your CC30.

Do you have any attachments other than just the deck itself?

However, feel free to double check here:

https://www.partstree.com/parts/cub-...ni-rider-2014/

J-Mech 08-27-2018 01:32 PM

Quote:

Originally Posted by Chad126 (Post 464842)
Just went through the entire parts list for this machine. Can't find anything that resembles this IF it is in fact a pin. Can't tell if the end of it is threaded. If it is a pin, and does not have any threads on the very end, I do not believe this came from your CC30.

If you can't tell what it is you are looking for, how can you be sure you did not find anything that "looks" like it?

Chad126 08-27-2018 01:45 PM

Quote:

Originally Posted by J-Mech (Post 464845)
If you can't tell what it is you are looking for, how can you be sure you did not find anything that "looks" like it?

Good question (in general), but not relative to my post. I do know a few options that I am looking for. I couldn't tell if it was threaded on the end, so I looked for all possible options.

I looked for ANY clevis pins, threaded carriages with a smooth shaft and threaded end, orany other pin with a slot like that one shown. I didn't find anything that could resemble what is pictured, threaded end or not. There are some threaded carriages in the parts list, but none I could find that had a slot or needed a slot. There are many subassemblies that are shown in the parts list, so perhaps it is part of one of them. However, the link is there. Perhaps he will have better luck.

finsruskw 08-27-2018 02:33 PM

You are looking at it and can't tell if it has/had threads??


All times are GMT -4. The time now is 08:41 PM.

Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.