Part of my Collection
 

Hi Gang,
Here are a few pictures of my collection. I will have to do some moving around in the shop to take pictures of the rest. ( Oh well the shop need cleaning anyways)
The 122 is on the operating table. The 124 w/ sleeve hitch sits in front of my '70 Pontiac Grand Prix SJ.
The 86 & 1320 sit next to the shop and the original will be next on the table (to old to work on the floor anymore).......lol
Enjoy:beer2:
Rod

whats your operating table made out of? 3/4 inch plywood? I like it!

Hi,
Yes 3/4 plywood, MDF for the top and 2X6's It has 6 6inch X 2inch castors on it so I can roll it around the shop The one end and middle castors swivel and the other end are stationary. I have a metal top that is being built to cover the top so I will be able to use my torch and welder on it. I can either lift up non running machines and set them on it or I have a 12 volt winch to pull them up with. The top is 30 inches from the floor and it is 4 ft X 8 ft with shelfs for storing the parts I take off of the toys....lol
Thanks for looking!
Rod

Good looking Cubs oldcubowner :ThumbsUp:

I like the operating table too. :bigthink: You got me thinkin again.:biggrin2.gif:

Nice looking Cubs. Nice table.. great idea.

Sweet idea on the table! Great looking bunch of cubs, I'd go nuts (and broke) having that many to tinker on.

Rod,

Nice collection you have there! :beerchug:

More Pictures of my Work Table
 

Hi,
Here are a couple more pictures of my work table. The height is almost the same as my tailgate to, which helps if I have one in the box. Let me know if anyone needs and more pictures.:beerchug:

Rod

122 Almost all Apart
 

Well the 122 is almost all apart. So far except for some pitting everything has came apart pretty good. No cracks as of yet, and no broken bolts. While finishing stripping my Original frame out I found 1 small problem, the front axel pivot pin was either worn out or broke at some point in time and they fixed it by welding a flat washer to the hole and used a bolt in place of the pin, oh well just more welding will be required.......lol
Enjoy

Rod

oldcubowner,

Not trying to sound like a wise guy or anything but the Originals used a shoulder bolt instead of a pin. Don't have time right now to go dig one up, I'll try to get you dimensions in a day or two.

I would never think of someone as a wise guy when they are being helpful and informative! This is the first Original I have had this far apart and didn't know it was a bolt. My only concern with it now is the welded washer and what I have to do to repair it the correct way.

Thank you for your help and the information. Also is the head of the Original bolt/pin fairly thin? If so this bolt maybe the correct bolt.

Thank You for the information!

Rod

Hey Rod, always nice to see someone with a Cub collection and even better to see another NY Cub collector. Where in the state are you located? I'm down here in Orange County.

Hi Mike,
Nice to meet you!
I live in South Lima about 20 miles south of Rochester in Livingston County. Not many Cub Collectors from around this area that are on here. I just picked up a 1650 it was in great shape until a track hoe backed into the right side and bent the frame fenders and twisted it enough to snap the left ftont spindle off. The deck is flat on the discharge side but the spindles still turn, so it is now a parts tractor. The engine runs great and the hood side shields are in great shape, not sure about the hydro yet. I bought it for the engine and sheet metal for a 16 hp puller I am building. Here are some pictures, I will take better ones once I get it unloaded onto my operating table,,,,,,,,,lol:bigthink:

Rod

Rod,

here is the only pic I have of the bolt. I can try for another better pic if needed..

http://i50.photobucket.com/albums/f3...s/100_0386.jpg

Hi Jay,
The bolt they used is threaded the entire lenght, so at some point they just welded a couple of washers and used a bolt with a pin through the end, Oh well just a bit more grinding and welding, Now to see what my parts tractor has for a pin. I will check it tomorrow and let you know.
Thanks for the picture!!!

Rod