PLEASE PATRONIZE OUR SPONSORS!
|
|
Thread Tools | Display Modes |
#11
|
|||
|
|||
Quote:
Ok. Pics later is good. |
#12
|
||||
|
||||
They run shop out of there fixing hydraulics' and high pressure fixings. Used to run 500psi sprayer they done must of the work to it. But cant afford them since I am not making money with this.
__________________
108, lights, electric mower and sleeve hitch. |
#13
|
|||
|
|||
For what I think it will take to fix this cylinder, I highly doubt they have the necessary equipment.
|
#14
|
||||
|
||||
I am hoping 2 new ones would be the better way for me to go. With very little knowledge.
__________________
108, lights, electric mower and sleeve hitch. |
#15
|
||||
|
||||
Hope that helps.
__________________
108, lights, electric mower and sleeve hitch. |
#16
|
||||
|
||||
NAPA makes hydraulic hoses/lines and are quite reasonable I hear.
Cub Cadet 123
__________________
Still don't know what I'm doing in OHIO?.....If you find me, then please point me back toward INDIANA. |
#17
|
||||
|
||||
Quote:
Thank you I do have a few that needs replaced.
__________________
108, lights, electric mower and sleeve hitch. |
#18
|
||||
|
||||
Try to stay away from an equipment dealer for hydraulics repairs if you can. The Bobcat dealership near me is too pricy to consider them for parts or service. The dealerships that sell those funny green colored machines are about the same.
If I can urge you to do anything, that is if you can, do some troubleshooting and some research as to what's wrong, what you have for sure and what your options are. Hydraulics have the advantage of a vast interchangeability of parts overall. Shops themselves (I'm in the Twin Cities, MN) vary vastly in prices of parts and services as well. I was quoted from $100-175 to rebuild my NF Add-On Unit cylinder from a number of shops but I'm doing it myself for approx. $35 which includes a new rod. I've seen welded cylinders rebuilt the same way/method with good results. It's not terribly hard even for a novice. Almost all cylinders can be serviced and brought back into service with the right parts. And there are all kinds of parts available. Sorry, back to the topic. I'm assuming the cylinders are drippy from your earlier posts. Where are the drippy from? Around the rod or where the hoses attach? If it's the rod, maybe only new seals are needed. Just my $.02
__________________
Mike - Ramsey, MN '65 100 - #126432 Options: V61's, 8.5" Tru-Powers, stock sleeve hitch, Xtreme sleeve hitch adapter Attachments: Dad's 42" Dozer Blade & 38" 3-spindle deck, 42U deck, Homemade Sleeve Hitch Dethatcher & a QA36A Snowthrower Mods: K301 Upgrade, IHinIN's clutch pivot upgrade, SST driveshaft, custom bar axles "Why buy something shiny & new when you can save something old." |
#19
|
||||
|
||||
Leaking from around the rod.
__________________
108, lights, electric mower and sleeve hitch. |
#20
|
||||
|
||||
Smokin, what Jonathan was asking is this. If you look at the ends of the cylinders can you see a clip that holds the end piece in place. If not, then you should be able to see where they welded it together. Think of 2 pieces of pipe being welded together to make one. If you have a clip on one end then you remove the clip, pull the guts out and repair it, if not it will need to be cut, repaired and rewelded.
__________________
This ain't no hobby....it's an addiction |
|
|
Cub Cadet is a premium line of outdoor power equipment, established in 1961 as part of International Harvester. During the 1960s, IH initiated an entirely new line of lawn and garden equipment aimed at the owners rural homes with large yards and private gardens. There were a wide variety of Cub Cadet branded and after-market attachments available; including mowers, blades, snow blowers, front loaders, plows, carts, etc. Cub Cadet advertising at that time harped on their thorough testing by "boys - acknowledged by many as the world's worst destructive force!". Cub Cadets became known for their dependability and rugged construction.
MTD Products, Inc. of Cleveland, Ohio purchased the Cub Cadet brand from International Harvester in 1981. Cub Cadet was held as a wholly owned subsidiary for many years following this acquisition, which allowed them to operate independently. Recently, MTD has taken a more aggressive role and integrated Cub Cadet into its other lines of power equipment.
This website and forum are not affiliated with or sponsored by MTD Products Inc, which owns the CUB CADET trademarks. It is not an official MTD Products Inc, website, and MTD Products Inc, is not responsible for any of its content. The official MTD Products Inc, website can be found at: http://www.mtdproducts.com. The information and opinions expressed on this website are the responsibility of the website's owner and/or it's members, and do not represent the opinions of MTD Products Inc. IH, INTERNATIONAL HARVESTER are registered trademark of CNH America LLC
All material, images, and graphics from this site are the property of www.onlycubcadets.net. Any unauthorized use, reproductions, or duplications are prohibited unless solely expressed in writing.
Cub Cadet, Cub, Cadet, IH, MTD, Parts, Tractors, Tractor, International Harvester, Lawn, Garden, Lawn Mower, Kohler, garden tractor equipment, lawn garden tractors, antique garden tractors, garden tractor, PTO, parts, online, Original, 70, 71, 72, 73, 76, SO76, 80, 81, 86, 100, 102, 104, 105, 106, 107, 108,109, 122, 123, 124, 125, 126, 127, 128, 129, 147, 149, 169, 182, 282, 382, 482, 580, 582, 582 Special, 680, 682, 782, 782D, 784, 800, 805, 882, 982, 984, 986, 1000, 1015, 1100, 1105, 1110, 1200, 1250, 1282, 1450, 1512, 1604, 1605, 1606, 1610, 1615, 1620, 1650, 1710, 1711, 1712, 1806, 1810, 1811, 1812, 1912, 1914.