PLEASE PATRONIZE OUR SPONSORS!
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Tiller lift?
I took the tiller lift off a 149 my question is about the shaft that goes through the frame of the tractor and the two bushings that are on the rear of the frame do the bushings come off the frame or are they welded on?
|
#2
|
|||
|
|||
Grab a hold of them.... did they come off in your hand?
http://www.cubcadet.com/equipment/AR...0-A/0025400025 |
#3
|
|||
|
|||
I used channel locks on them, no luck are they pressed in? or welded?
|
#4
|
|||
|
|||
They are welded.
Even if they were pressed it, why would you want to take them out? |
#5
|
|||
|
|||
To use the lift on a different tractor. I have two 1450s that I looked at one has the bushings one does not? Can you buy the bushings for a tractor that doesn't have them? Would they have to be welded on?
|
#6
|
|||
|
|||
No. A 1450 tractor (and newer) takes a different mount. You need a pair of "Frankenstein" bolts to mount the lift.
You can buy a set from Jeff: http://www.onlycubcadets.net/forum/s...ad.php?t=20875 |
#7
|
||||
|
||||
I may be misunderstanding his question but I think he means these things.
the first picture is from the 149 parts manual, the second is from the 1250 manual. I don't know if the 1250's would be welded or pressed. I have a 1200 but it's not handy right now. The p/n for #20 below is 393 831 r1 and they refer to is as "washer". |
Thread Tools | |
Display Modes | |
|
|
Cub Cadet is a premium line of outdoor power equipment, established in 1961 as part of International Harvester. During the 1960s, IH initiated an entirely new line of lawn and garden equipment aimed at the owners rural homes with large yards and private gardens. There were a wide variety of Cub Cadet branded and after-market attachments available; including mowers, blades, snow blowers, front loaders, plows, carts, etc. Cub Cadet advertising at that time harped on their thorough testing by "boys - acknowledged by many as the world's worst destructive force!". Cub Cadets became known for their dependability and rugged construction.
MTD Products, Inc. of Cleveland, Ohio purchased the Cub Cadet brand from International Harvester in 1981. Cub Cadet was held as a wholly owned subsidiary for many years following this acquisition, which allowed them to operate independently. Recently, MTD has taken a more aggressive role and integrated Cub Cadet into its other lines of power equipment.
This website and forum are not affiliated with or sponsored by MTD Products Inc, which owns the CUB CADET trademarks. It is not an official MTD Products Inc, website, and MTD Products Inc, is not responsible for any of its content. The official MTD Products Inc, website can be found at: http://www.mtdproducts.com. The information and opinions expressed on this website are the responsibility of the website's owner and/or it's members, and do not represent the opinions of MTD Products Inc. IH, INTERNATIONAL HARVESTER are registered trademark of CNH America LLC
All material, images, and graphics from this site are the property of www.onlycubcadets.net. Any unauthorized use, reproductions, or duplications are prohibited unless solely expressed in writing.
Cub Cadet, Cub, Cadet, IH, MTD, Parts, Tractors, Tractor, International Harvester, Lawn, Garden, Lawn Mower, Kohler, garden tractor equipment, lawn garden tractors, antique garden tractors, garden tractor, PTO, parts, online, Original, 70, 71, 72, 73, 76, SO76, 80, 81, 86, 100, 102, 104, 105, 106, 107, 108,109, 122, 123, 124, 125, 126, 127, 128, 129, 147, 149, 169, 182, 282, 382, 482, 580, 582, 582 Special, 680, 682, 782, 782D, 784, 800, 805, 882, 982, 984, 986, 1000, 1015, 1100, 1105, 1110, 1200, 1250, 1282, 1450, 1512, 1604, 1605, 1606, 1610, 1615, 1620, 1650, 1710, 1711, 1712, 1806, 1810, 1811, 1812, 1912, 1914.