Only Cub Cadets

PLEASE PATRONIZE OUR SPONSORS!

CC Speciaalties R. F. Houtz and Sons

Patton Acres IH Cub Cadet Parts

Cub Cadet Parts & Service


If you would like to help maintain this site & enhance it, feel free to donate whatever amount you would like to!




Attention Folks we have a new owner!
Greg Rozar AKA- CubDieselFan


Go Back   Only Cub Cadets > Cub Cadets > Implements and Attachments

Notices

Reply
 
Thread Tools Display Modes
  #1  
Old 08-04-2009, 08:07 AM
wshytle wshytle is offline
Senior Member
 
Join Date: Jul 2009
Location: North Carolina
Posts: 197
Default 44A Spindle rebuild?

Hi Guys,
I have a couple of 44A decks and I have spindle issues on both. My question is can the bearings be replaced or does one have to replace the spindle assembly? A nearby IH dealer offered to send a spindle to my door for $175. If it is possible to install new bearing how do you get these bearings out? This is yet another first for me so any advice will be appreciated.
Thanks for any and all response. Wayne
Reply With Quote
  #2  
Old 08-05-2009, 05:52 AM
R Bedell R Bedell is offline
Administrator
 
Join Date: Mar 2007
Location: Michigan
Posts: 13,693
Default

Wayne:

Here is what you got........



These bearings (ST745) are non serviceable. These bearings need to be replaced.



You can obtain replacements from your local CC or Case/IH Dealer. You can also obtain these from our Forum Sponsors at the top of the page. You can also check with the Dealers in our Parts Sources Section.
__________________
Roland Bedell

CC Models: 100, 105, 1450, 782, (2) 784, & 2072

Buy: Made in the USA
Reply With Quote
  #3  
Old 08-05-2009, 06:42 AM
wshytle wshytle is offline
Senior Member
 
Join Date: Jul 2009
Location: North Carolina
Posts: 197
Default

R Bedell - Thank you for the information. It's hard for me to understand why IH would make such a part, with zerks, to be disposable. With todays costs to replace and repair, I'm thinking conspiracy. I assume the machined shaft is the main reason for expense. Oh well, on to the next project..
Reply With Quote
  #4  
Old 08-05-2009, 11:17 AM
RChristensen RChristensen is offline
Inactive Member
 
Join Date: Mar 2009
Location: Gilbert AZ
Posts: 119
Default

I'm not so sure on the conspiracy thing, they only lasted thirty some years. How many box store mowers will last three to four years?????
Reply With Quote
  #5  
Old 08-05-2009, 01:59 PM
Matt G.'s Avatar
Matt G. Matt G. is offline
Senior Member
 
Join Date: Mar 2009
Location: Wichita, KS
Posts: 5,661
Default

They'll last just about forever if they are greased properly...but the problem is that few of these decks had great maintenance. I've had some really nice ones that had probably been greased before every use.
Reply With Quote
  #6  
Old 08-05-2009, 08:34 PM
wshytle wshytle is offline
Senior Member
 
Join Date: Jul 2009
Location: North Carolina
Posts: 197
Default

You're right guys - Everything about these machines is pretty much bullet-proof. I just don't understand why these spindles don't have replacable bearings. They have such a nice, machined shafts that it just seems a waste. I have three 44As and all three shells are good to very good. 5 out of the 9 spindles are bad. Oh well... Conspiracy was probably the wrong term.
Reply With Quote
  #7  
Old 12-03-2015, 04:53 PM
84Buckeye 84Buckeye is offline
Member
 
Join Date: Mar 2013
Location: Ohio
Posts: 34
Default

Hey guys! Realize this is going back a few years but I was wondering if somebody could help me out here with couple questions. My 44A spindles are toast.

Can I get the ST745 Bearings only? I'm having the deck powder coated by a friend who has a business doing this. HE seems to think #5, #6 and #7 will coat too once they're blasted.

This way I could get out around 70 bucks for each bearing, instead of around 160 for the whole assembly. Can't see it being an issue, anybody have any thoughts with this?

Also, that cover #5, it isn't tacked on that cup #7 is it? Mine wasn't, it was loose.
Reply With Quote
  #8  
Old 12-03-2015, 05:56 PM
R Bedell R Bedell is offline
Administrator
 
Join Date: Mar 2007
Location: Michigan
Posts: 13,693
Default

Quote:
Can I get the ST745 Bearings only?
You sure can.

Quote:
Also, that cover #5, it isn't tacked on that cup #7 is it?
Nope, hence the two different part numbers
__________________
Roland Bedell

CC Models: 100, 105, 1450, 782, (2) 784, & 2072

Buy: Made in the USA
Reply With Quote
  #9  
Old 12-03-2015, 06:02 PM
darkminion_17's Avatar
darkminion_17 darkminion_17 is offline
Grand Member
 
Join Date: Aug 2010
Location: New Jersey
Posts: 10,984
Default

I have a thought...
# 5 and 7 should be replaced.I had a good set of bearings but they were loose in their housings.New housings took care of it,blast them and they can be PC'd.
__________________
Up to 530 and counting...
I give up updating my profile!
Reply With Quote
  #10  
Old 12-03-2015, 06:35 PM
84Buckeye 84Buckeye is offline
Member
 
Join Date: Mar 2013
Location: Ohio
Posts: 34
Default

Thanks for the replies guys! Appears those housing cups are around 70 each, plus cover another 20. At that point, might as well just go ahead and buy the entire assembly.

Not to sound like a cheapskate, but that's a near a 300 dollar decision.
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 06:00 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.

Cub Cadet is a premium line of outdoor power equipment, established in 1961 as part of International Harvester. During the 1960s, IH initiated an entirely new line of lawn and garden equipment aimed at the owners rural homes with large yards and private gardens. There were a wide variety of Cub Cadet branded and after-market attachments available; including mowers, blades, snow blowers, front loaders, plows, carts, etc. Cub Cadet advertising at that time harped on their thorough testing by "boys - acknowledged by many as the world's worst destructive force!". Cub Cadets became known for their dependability and rugged construction.

MTD Products, Inc. of Cleveland, Ohio purchased the Cub Cadet brand from International Harvester in 1981. Cub Cadet was held as a wholly owned subsidiary for many years following this acquisition, which allowed them to operate independently. Recently, MTD has taken a more aggressive role and integrated Cub Cadet into its other lines of power equipment.

This website and forum are not affiliated with or sponsored by MTD Products Inc, which owns the CUB CADET trademarks. It is not an official MTD Products Inc, website, and MTD Products Inc, is not responsible for any of its content. The official MTD Products Inc, website can be found at: http://www.mtdproducts.com. The information and opinions expressed on this website are the responsibility of the website's owner and/or it's members, and do not represent the opinions of MTD Products Inc. IH, INTERNATIONAL HARVESTER are registered trademark of CNH America LLC

All material, images, and graphics from this site are the property of www.onlycubcadets.net. Any unauthorized use, reproductions, or duplications are prohibited unless solely expressed in writing.

Cub Cadet, Cub, Cadet, IH, MTD, Parts, Tractors, Tractor, International Harvester, Lawn, Garden, Lawn Mower, Kohler, garden tractor equipment, lawn garden tractors, antique garden tractors, garden tractor, PTO, parts, online, Original, 70, 71, 72, 73, 76, SO76, 80, 81, 86, 100, 102, 104, 105, 106, 107, 108,109, 122, 123, 124, 125, 126, 127, 128, 129, 147, 149, 169, 182, 282, 382, 482, 580, 582, 582 Special, 680, 682, 782, 782D, 784, 800, 805, 882, 982, 984, 986, 1000, 1015, 1100, 1105, 1110, 1200, 1250, 1282, 1450, 1512, 1604, 1605, 1606, 1610, 1615, 1620, 1650, 1710, 1711, 1712, 1806, 1810, 1811, 1812, 1912, 1914.