Only Cub Cadets

PLEASE PATRONIZE OUR SPONSORS!

CC Speciaalties R. F. Houtz and Sons

Patton Acres IH Cub Cadet Parts

Cub Cadet Parts & Service


If you would like to help maintain this site & enhance it, feel free to donate whatever amount you would like to!




Attention Folks we have a new owner!
Greg Rozar AKA- CubDieselFan


Go Back   Only Cub Cadets > Cub Cadets > Cub Cadet Engines > Briggs & Stratton Engines

Notices

Reply
 
Thread Tools Display Modes
  #1  
Old 07-07-2014, 09:59 AM
Oak's Avatar
Oak Oak is offline
Senior Moderator
 
Join Date: Jun 2009
Location: Georgia
Posts: 5,047
Default Valve guide question

Okay guys, I pulled the engine on the 3165 to pull the tins and check for cooling issues and figured it would be a good time to adjust the valves if needed. That's where the fun started. I noticed on the #1 cylinder (opposite the oil filter) the valve push rod was bending each time it would lift the valve. It looks like the valve guide started backing out of the head and limiting the valve movement causing the push rod to bend.

What do I need to do at this point? I'm thinking if I push it back in it will work its way back out and if I replace it, will the new one do the same. Looks like a quick search on a new head is a little over $200. I'm not sure what it would cost if I take it to a machine shop to have them repair it but I'm thinking that would be at least $100.

Here you can see the guide on the left is backing out.
DSCN1255.jpg
__________________
This ain't no hobby....it's an addiction
Reply With Quote
  #2  
Old 07-07-2014, 10:17 AM
Sam Mac's Avatar
Sam Mac Sam Mac is offline
Administrator
 
Join Date: Feb 2010
Location: Galax VA
Posts: 18,745
Default

Todd

Had the same issue with the engine that came out of that 1641 I bought from Earl AKA DaDuke. I just pressed it back it, cleaned the crud off the valves and replaced the bent pushrods. The engine is now in my pressure washer. So far it's been running fine. Think it pushed the guide up because it got hot. Engine had so many things screwed up on it I'm surprised it even ran. I'm not suggesting that you do what I did on one that will be worked hard.
Attached Images
File Type: jpg IMG_3094.jpg (22.6 KB, 207 views)
File Type: jpg IMG_2949.jpg (26.9 KB, 206 views)
__________________
2264 with 54 GT deck
1641 AKA Black Jack with a 402-E Haban Sickle bar mower
JD317 dump truck
BX2670 with FEL
Reply With Quote
  #3  
Old 07-07-2014, 10:24 AM
Oak's Avatar
Oak Oak is offline
Senior Moderator
 
Join Date: Jun 2009
Location: Georgia
Posts: 5,047
Default

Wow, those rods are bent! Should I use some type of retaining compound like loctite or just push them back in?
__________________
This ain't no hobby....it's an addiction
Reply With Quote
  #4  
Old 07-07-2014, 10:36 AM
Sam Mac's Avatar
Sam Mac Sam Mac is offline
Administrator
 
Join Date: Feb 2010
Location: Galax VA
Posts: 18,745
Default

If it was me I'd check with a machine shop about putting in some knurled valve guides in those heads if someone makes them. Don't think Loc-Tite will work with the heat.
__________________
2264 with 54 GT deck
1641 AKA Black Jack with a 402-E Haban Sickle bar mower
JD317 dump truck
BX2670 with FEL
Reply With Quote
  #5  
Old 07-07-2014, 06:06 PM
J-Mech J-Mech is offline
Banned
 
Join Date: Apr 2013
Location: Oblong, Illinois
Posts: 17,594
Default

You can use sleeve retainer lock-tite. It's made for dry sleeved motors. But, I'm with Sam, if you going to use it hard, then I'd get another head. Been my experience with any aluminum head that once the guide comes out, they generally won't stay put. I guess you can try sleeve retainer and knurling it (good idea Sam).... if it doesn't work you'll be back where you are now.
Reply With Quote
  #6  
Old 07-08-2014, 08:19 AM
Oak's Avatar
Oak Oak is offline
Senior Moderator
 
Join Date: Jun 2009
Location: Georgia
Posts: 5,047
Default

Well, I'm selling this tractor and I hate to dump more money into it but I don't want to sell someone a ticking time bomb either. I did some searching and I tried Pats Small Engine Plus for parts. I ordered a new head, push rod, front and rear seals, exhaust gasket, (4) head bolts and a new starter gear for a total of about $250 shipped. I called a local machine shop that works on small engines but they said i would be better off replacing it...I kinda figured that was what they were going to say. Now me and the dog gotta look for the big brown truck.
__________________
This ain't no hobby....it's an addiction
Reply With Quote
  #7  
Old 12-01-2015, 01:16 PM
Mike McKown Mike McKown is offline
Grand Member
 
Join Date: Jul 2012
Location: Indiana
Posts: 1,825
Default

Quote:
Originally Posted by Sam Mac View Post
Todd

Had the same issue with the engine that came out of that 1641 I bought from Earl AKA DaDuke. I just pressed it back it, cleaned the crud off the valves and replaced the bent pushrods. The engine is now in my pressure washer. So far it's been running fine. Think it pushed the guide up because it got hot. Engine had so many things screwed up on it I'm surprised it even ran. I'm not suggesting that you do what I did on one that will be worked hard.
Sam,

Is your 16 Vanguard still running on that shade tree fix?

I picked up a low hour 1641 a couple days ago and it had a guide that had slipped up and bent the pushrod. I hammered it back down and straigtened the pushrod and it is now going up and down like it's supposed to.

I haven't gotten the engine hot yet so I don't know if it will last or not. Didn't figure I had much to lose.

I just wondered how yours came out?
Reply With Quote
  #8  
Old 12-01-2015, 01:30 PM
Sam Mac's Avatar
Sam Mac Sam Mac is offline
Administrator
 
Join Date: Feb 2010
Location: Galax VA
Posts: 18,745
Default

Mike

So far no problems but it is now in a low stress application and get's little use. I installed it in my pressure washer that had an 8HP Tecumseh engine. At least it's easier to start than the Tecumseh was.
Attached Images
File Type: jpg IMG_3241.jpg (28.6 KB, 92 views)
File Type: jpg IMG_3245.jpg (28.9 KB, 91 views)
__________________
2264 with 54 GT deck
1641 AKA Black Jack with a 402-E Haban Sickle bar mower
JD317 dump truck
BX2670 with FEL
Reply With Quote
  #9  
Old 12-01-2015, 02:23 PM
Mike McKown Mike McKown is offline
Grand Member
 
Join Date: Jul 2012
Location: Indiana
Posts: 1,825
Default

Thanks, just checking. I fired the engine up while ago and the rockers are rockin' and boppin' just like they're supposed to. Engine doesn't knock or smoke so I think I'll leave it be and see what happens.

Your comment about overheating. When the engine fired, part of a mouse house blew out of the shrouding so it's very possible things are plugged around the cooling fins.
Reply With Quote
  #10  
Old 12-01-2015, 04:32 PM
Sam Mac's Avatar
Sam Mac Sam Mac is offline
Administrator
 
Join Date: Feb 2010
Location: Galax VA
Posts: 18,745
Default

Over heating will do it.
__________________
2264 with 54 GT deck
1641 AKA Black Jack with a 402-E Haban Sickle bar mower
JD317 dump truck
BX2670 with FEL
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 12:21 PM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.

Cub Cadet is a premium line of outdoor power equipment, established in 1961 as part of International Harvester. During the 1960s, IH initiated an entirely new line of lawn and garden equipment aimed at the owners rural homes with large yards and private gardens. There were a wide variety of Cub Cadet branded and after-market attachments available; including mowers, blades, snow blowers, front loaders, plows, carts, etc. Cub Cadet advertising at that time harped on their thorough testing by "boys - acknowledged by many as the world's worst destructive force!". Cub Cadets became known for their dependability and rugged construction.

MTD Products, Inc. of Cleveland, Ohio purchased the Cub Cadet brand from International Harvester in 1981. Cub Cadet was held as a wholly owned subsidiary for many years following this acquisition, which allowed them to operate independently. Recently, MTD has taken a more aggressive role and integrated Cub Cadet into its other lines of power equipment.

This website and forum are not affiliated with or sponsored by MTD Products Inc, which owns the CUB CADET trademarks. It is not an official MTD Products Inc, website, and MTD Products Inc, is not responsible for any of its content. The official MTD Products Inc, website can be found at: http://www.mtdproducts.com. The information and opinions expressed on this website are the responsibility of the website's owner and/or it's members, and do not represent the opinions of MTD Products Inc. IH, INTERNATIONAL HARVESTER are registered trademark of CNH America LLC

All material, images, and graphics from this site are the property of www.onlycubcadets.net. Any unauthorized use, reproductions, or duplications are prohibited unless solely expressed in writing.

Cub Cadet, Cub, Cadet, IH, MTD, Parts, Tractors, Tractor, International Harvester, Lawn, Garden, Lawn Mower, Kohler, garden tractor equipment, lawn garden tractors, antique garden tractors, garden tractor, PTO, parts, online, Original, 70, 71, 72, 73, 76, SO76, 80, 81, 86, 100, 102, 104, 105, 106, 107, 108,109, 122, 123, 124, 125, 126, 127, 128, 129, 147, 149, 169, 182, 282, 382, 482, 580, 582, 582 Special, 680, 682, 782, 782D, 784, 800, 805, 882, 982, 984, 986, 1000, 1015, 1100, 1105, 1110, 1200, 1250, 1282, 1450, 1512, 1604, 1605, 1606, 1610, 1615, 1620, 1650, 1710, 1711, 1712, 1806, 1810, 1811, 1812, 1912, 1914.