PLEASE PATRONIZE OUR SPONSORS!
|
|
Thread Tools | Display Modes |
#1
|
||||
|
||||
Have a few questions about my 1250...
First question is what thread size bolt do i need to hold my side panels on? (Like 5/16 or 1/4 or something along those lines) I've tried looking everywhere and can't find anything on them. Second and final question is what diameter is the trunion shaft? I will eventually be pulling off my fender pan and repairing the trunion ( should have done it when i had the transaxle out but i didn't think it would be as bad as it is,) and my damper plate is fairly loose. I think I'm going to reweld the trunion, tighten up the damper plate and replace the springs while I'm in there as it seems that's where most of my creeping problems come from. As always, any answers are greatly appreciated.
__________________
'78 1250, '79 1450 Trapped and released: 124, 1000, 72, 1211 (JD) '86 316, '70 140 H3 patio yellow, '74 140 H3, '86 330 diesel, '87 214 Attachments: Brinly plows, cultivator, kk-300 planter, many mower decks, #2 cart, #1 tiller w/ 2 exts. & #1a w/ 2 exts, , JD 50 & 80 (3x) carts, 2 JD 54" blades, IH 42" blade, 3pt disk, several sleeve hitches, too much stuff to list! |
#2
|
||||
|
||||
1/4" to hold the side panel on. Don't know off hand about your second question.
__________________
Make the best of each day , Todd Original's Face Lift thread.http://www.onlycubcadets.net/forum/s...ad.php?t=34439 (O) Start to Finish video.https://www.youtube.com/watch?v=GAoUNNiLwKs Wheel Around videohttps://www.youtube.com/watch?v=XUL-m6Bramk They can't all be turn key! |
#3
|
||||
|
||||
Thread size is 1/4"-20 for side panels.
If you are talking about shimming the pivot of the damper and control plates: Damper 5/8" ID Shims Control 1/2" ID Shims Grab some .005 and .010 shims for both sizes so you can dial it in, as well as new retaining rings. It helps tighten things up if they aren't distorted. More info here: http://cubfaq.com/hydrolurch.html
__________________
http://www.solunagarage.com |
#4
|
||||
|
||||
Okay thank you guys very much. I'll have to find or pick up some bolts this weekend. Thanks for the info on the hydro shimming process. I just remembered reading that cubFAQ article about a month ago but forgot about it. Just need to find a spring for the front (seen one on ebay for 10 bucks. Maybe I'll pick it up.) And get the shims.
__________________
'78 1250, '79 1450 Trapped and released: 124, 1000, 72, 1211 (JD) '86 316, '70 140 H3 patio yellow, '74 140 H3, '86 330 diesel, '87 214 Attachments: Brinly plows, cultivator, kk-300 planter, many mower decks, #2 cart, #1 tiller w/ 2 exts. & #1a w/ 2 exts, , JD 50 & 80 (3x) carts, 2 JD 54" blades, IH 42" blade, 3pt disk, several sleeve hitches, too much stuff to list! |
#5
|
|||
|
|||
For the spring pick up a screen door spring at the hardware store and rebend the ends to fit. Probably have to shorten it a little too. Should cost about 3 bucks.
|
#6
|
|||
|
|||
I find it more convenient to use knobs instead of bolts. You can usually find them in the hardware bins at your local hardware store. I usually use them in conjunction with a SS fender washer. I also find that a throttle or clutch return spring works well at the front.
|
#7
|
||||
|
||||
Put a piece of rubber hose over the spring, it need not be full length, any old useless fuel line will work, it keeps the spring from vibrating/making a weird sound. ( harmonics)
If you like to tinker and remove the side panels often, put the bolts in from the back side and pick up a couple of wing nuts or knobs as suggested,---- makes it easier/quicker on/off |
#8
|
||||
|
||||
Ok guys, i just thought of one more question. When i was installing my hydraulic lift, i somehow broke a terminal of my pto fuse holder. I rigged up a blade fuse holder and quickly realized it doesn't work with the pto. Can i just swap the light fuse wires for the pto and use the blade fuse holder for the lights? I know it probably sounds silly but i know the lights will work fine with the blade fuse, but i don't know if the two dash fuse holders can hold the same current. Also, thanks to all the guys who helped out with the first questions. I'm still sort of a newie to the ins and outs of Cubs. All I've ever owned was deeres and thought it was time to branch out to more brands.
__________________
'78 1250, '79 1450 Trapped and released: 124, 1000, 72, 1211 (JD) '86 316, '70 140 H3 patio yellow, '74 140 H3, '86 330 diesel, '87 214 Attachments: Brinly plows, cultivator, kk-300 planter, many mower decks, #2 cart, #1 tiller w/ 2 exts. & #1a w/ 2 exts, , JD 50 & 80 (3x) carts, 2 JD 54" blades, IH 42" blade, 3pt disk, several sleeve hitches, too much stuff to list! |
#9
|
|||
|
|||
No reason the blade fuse holder wouldn't work with the PTO. You must have another issue. Both fuse holders on the tractor are identical.
|
#10
|
||||
|
||||
I popped in a 10 amp after plugging in the pto wires, flipped on the pto on (with no load) and it blew it almost immediately. I'm just gonna swap them around so the pto is on the dash fuse and the lights are on the blade fuse.Only reason i asked was because the lower fuse holder looked different than the top. But i don't have a blower or tiller for it so i don't need the pto until spring when i throw the deck on.
__________________
'78 1250, '79 1450 Trapped and released: 124, 1000, 72, 1211 (JD) '86 316, '70 140 H3 patio yellow, '74 140 H3, '86 330 diesel, '87 214 Attachments: Brinly plows, cultivator, kk-300 planter, many mower decks, #2 cart, #1 tiller w/ 2 exts. & #1a w/ 2 exts, , JD 50 & 80 (3x) carts, 2 JD 54" blades, IH 42" blade, 3pt disk, several sleeve hitches, too much stuff to list! |
|
|
Cub Cadet is a premium line of outdoor power equipment, established in 1961 as part of International Harvester. During the 1960s, IH initiated an entirely new line of lawn and garden equipment aimed at the owners rural homes with large yards and private gardens. There were a wide variety of Cub Cadet branded and after-market attachments available; including mowers, blades, snow blowers, front loaders, plows, carts, etc. Cub Cadet advertising at that time harped on their thorough testing by "boys - acknowledged by many as the world's worst destructive force!". Cub Cadets became known for their dependability and rugged construction.
MTD Products, Inc. of Cleveland, Ohio purchased the Cub Cadet brand from International Harvester in 1981. Cub Cadet was held as a wholly owned subsidiary for many years following this acquisition, which allowed them to operate independently. Recently, MTD has taken a more aggressive role and integrated Cub Cadet into its other lines of power equipment.
This website and forum are not affiliated with or sponsored by MTD Products Inc, which owns the CUB CADET trademarks. It is not an official MTD Products Inc, website, and MTD Products Inc, is not responsible for any of its content. The official MTD Products Inc, website can be found at: http://www.mtdproducts.com. The information and opinions expressed on this website are the responsibility of the website's owner and/or it's members, and do not represent the opinions of MTD Products Inc. IH, INTERNATIONAL HARVESTER are registered trademark of CNH America LLC
All material, images, and graphics from this site are the property of www.onlycubcadets.net. Any unauthorized use, reproductions, or duplications are prohibited unless solely expressed in writing.
Cub Cadet, Cub, Cadet, IH, MTD, Parts, Tractors, Tractor, International Harvester, Lawn, Garden, Lawn Mower, Kohler, garden tractor equipment, lawn garden tractors, antique garden tractors, garden tractor, PTO, parts, online, Original, 70, 71, 72, 73, 76, SO76, 80, 81, 86, 100, 102, 104, 105, 106, 107, 108,109, 122, 123, 124, 125, 126, 127, 128, 129, 147, 149, 169, 182, 282, 382, 482, 580, 582, 582 Special, 680, 682, 782, 782D, 784, 800, 805, 882, 982, 984, 986, 1000, 1015, 1100, 1105, 1110, 1200, 1250, 1282, 1450, 1512, 1604, 1605, 1606, 1610, 1615, 1620, 1650, 1710, 1711, 1712, 1806, 1810, 1811, 1812, 1912, 1914.