Only Cub Cadets

PLEASE PATRONIZE OUR SPONSORS!

Cub Cadet Classics R. F. Houtz and Sons

Patton Acres Binder Books

ccspecialtiesParts by Jeff


If you would like to help maintain this site & enhance it, feel free to donate whatever amount you would like to!



Only Cub Cadets Chat!

OCC Archives


Go Back   Only Cub Cadets > Resources > Cub Cadet Parts Sources

Notices

Closed Thread
 
Thread Tools Display Modes
  #1  
Old 10-28-2012, 07:00 PM
Jeff in Pa's Avatar
Jeff in Pa Jeff in Pa is offline
Grand Member
 
Join Date: Feb 2012
Location: Zionsville, PA
Posts: 2,793
Default Parts by Jeff-sleeve hitch, PTO buttons and custom parts

I make a large variety of parts for Cub Cadets. I can make custom parts too. All parts are made by myself, I'm a machinist / fabricator with over thirty years experience.

Please contact me by: PM or E-mail at: JRDerstine@gmail.com

~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ ~~~~~~~~~~
Heavy duty sleeve hitch adapter with two drilled lifting straps or two slotted lifting straps

$110 plus shipping
$125 plus shipping with one set of drilled and one set of slotted straps

Add a Lift Pin for an additional $10
triple drilled lift pin for an additional $15
Extended length to clear tiller mount add $5
I can make these custom length if needed.

~~~~~~~
Lift Pin for rear lift casting, double hole. I drill these so they can be positioned with the holes vertical or horizontal. They are secured with a 3/16" cotter pin and also have a cotter pin where it goes thru the casting.

$17 plus shipping

triple drilled long length available too
~~~~~~~~~


Height adjuster Knob for 1/1A/2A tillers using 1/2-13 threaded rod. Has correct milled radius on bottom to match rear lift pin.



$18 plus shipping
~~~~~~~~~~~

1/2-13NC threaded rod for use with above knob ( or factory knob )

$6 plus shipping
~~~~~~~~~

Brass PTO button

$5.50 each plus shipping

~~~~~~~

Pair of "frankenstein" bolt and nuts for WF rear lifts

$30 plus shipping

~~~~~~~~~

Pair of straps for the front of the QA mounts. No more fumbling with bolts,nuts and washers. Slide these in the hole and secure with a 1/2-13NC in the factory welded nut inside the frame.


$12 plus shipping

~~~~~~~~~~~

Solid Motor Mounts for QL & WF tractors, with washers, Grade 8 flanged bolts and nylock nuts.

$40 plus shipping for set of four.




~~~~~~~~~~~
Headlight rings for 1X2/1X3/1X4/1X5


$32 per pair plus shipping

~~~~~~~~~~~
See later posts for original lift pin and QA36 / QA42 / QA36A / QA42A belt tensioner adjustment parts

~~~~~~~~~~~~~

If you order more than one item, I will do my best to keep shipping costs as low as possible.


All parts manufactured by me and mailed from the Palm,PA post office
Please either PM or email me
Thanks
Jeff
  #2  
Old 03-29-2013, 08:10 PM
Jeff in Pa's Avatar
Jeff in Pa Jeff in Pa is offline
Grand Member
 
Join Date: Feb 2012
Location: Zionsville, PA
Posts: 2,793
Default

90° Gear Box Shafts for tillers and snow throwers. Made from 3/4" diameter 4140 P alloy steel ( turned ,ground and polished ) with on size keyways and snap ring grooves cut.



$48 each or $92 for the pair plus shipping

If you have a "BB" angle drive gear box, I can make those shafts if you send me the shaft to copy ( it will be returned if wanted )

Just found out there are two different lengths of the short shaft in the 90* gear box. One ( as pictured above ) at 4-21/64" long and the other at 4-1/8" long.
Just let me know which one you want.


~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

Two more different lengths. Top on is 5-15/16" long and the bottom is 4-9/64" long


~~~~~~~~~~~~~~~~~~~~~~~~~~~~

Transfer shaft for the QA snow throwers. $32 plus shipping or $30 with either ( or both ) of the above 90* gear box shafts


~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
PTO pulley puller

The pulley puller uses the 5/16" threaded holes in the pulley to pull it off much easier.
Each unit is supplied with handle and threaded rod with centering point to locate on the crankshaft. Use a 9/16" wrench or socket.



It's used as shown here ( version shown in pictures does not have the weld cutouts, all pullers have that now)


$22 each plus shipping

~~~~~~~~~~~~~

Ross steering box adjustment screw (Cam Follower)



$8 plus shipping
  #3  
Old 01-07-2014, 02:53 PM
Jeff in Pa's Avatar
Jeff in Pa Jeff in Pa is offline
Grand Member
 
Join Date: Feb 2012
Location: Zionsville, PA
Posts: 2,793
Default

Adjustable length Lift Bar for front mounted implements. Adjust range of just under 28" to over 32" ( can make custom length if needed )

$35 plus shipping





~~~~~~~~~~~~~~~~

NF Lift Bracket for front mounted blade

$30 plus shipping



~~~~~~~~~~~~~~~~

Lift Bracket for either hydraulic lift or electric lift. This is the cut down version of the manual style.

$17 for the drilled , $20 for the slotted plus shipping



~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Receiver Hitch for the 82 series tractors. It bolts to the upright frame in the back.





$50 plus shipping
  #4  
Old 01-19-2014, 11:41 AM
Jeff in Pa's Avatar
Jeff in Pa Jeff in Pa is offline
Grand Member
 
Join Date: Feb 2012
Location: Zionsville, PA
Posts: 2,793
Default

~~~~~~~~~~~

Original style Lift Pin


$22 plus shipping

~~~~~~~~~~~~~

Tensioner Bolt for QA36 / QA 42 / QA36A / QA42A belt with castle nut & plate button . This style has a welded nut in the end for use with 3/4" wrench. ( original style will offered later after I bend up handles)

These are 1/2 -13 LEFT HAND thread






I'll also sell just the bolt and castle nut too


Complete unit as shown $30 plus shipping
Adjustment bolt with castle nut $17 plus shipping
Plate button $17 plus shipping
  #5  
Old 02-23-2014, 06:12 PM
Jeff in Pa's Avatar
Jeff in Pa Jeff in Pa is offline
Grand Member
 
Join Date: Feb 2012
Location: Zionsville, PA
Posts: 2,793
Default

Attachment Brackets for lift handle, both NF & WF.


$22 plus shipping

~~~~~~~~



Wide Frame rear lift attachment bracket also $22 plus shipping


~~~~~~~~~~~~~~~~~~~~~~~

  #6  
Old 03-23-2014, 09:12 PM
Jeff in Pa's Avatar
Jeff in Pa Jeff in Pa is offline
Grand Member
 
Join Date: Feb 2012
Location: Zionsville, PA
Posts: 2,793
Default

Driveshafts now being offered

Made from 4140 alloy steel

Prices are $45 plus shipping for welded flange style


and $30 plus shipping for drilled only.

~~~~~~~~~~~~~~~~~~~~~~~~~~~~

Driveshaft Couplers
for 5/8" driveshaft to creeper gearbox or manual transmission.



$25 plus shipping ( if purchased with a driveshaft, $20 )

~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

Drive Hubs - $45 plus shipping. One piece design for added strength

  #7  
Old 08-03-2014, 07:20 PM
Jeff in Pa's Avatar
Jeff in Pa Jeff in Pa is offline
Grand Member
 
Join Date: Feb 2012
Location: Zionsville, PA
Posts: 2,793
Default

Rear Lift Pin - Triple drilled pin for rear lift casting. I drill these so they can be positioned with the holes vertical or horizontal. They are secured with a 3/16" cotter pin and also have a cotter pin where it goes thru the casting.


$22 plus shipping
( $17 with sleeve hitch adapter order )
  #8  
Old 10-01-2014, 08:12 PM
Jeff in Pa's Avatar
Jeff in Pa Jeff in Pa is offline
Grand Member
 
Join Date: Feb 2012
Location: Zionsville, PA
Posts: 2,793
Default

Transfer Shaft for the QA snow throwers. $32 plus shipping or $30 with either ( or both ) of the 90* gear box shafts
  #9  
Old 08-24-2015, 06:21 PM
Alvy's Avatar
Alvy Alvy is online now
Grand Member
 
Join Date: Jul 2012
Location: Florida
Posts: 3,108
Thumbs up

Thank you again Jeff in PA. Highly recommend asking Jeff to make some odd ball stuff that you may need as he just sent me a wide frame creeper handle and steer axle pin and bushings for my 108 project. Top knotch quality, fitment, etc. thanks Jeff

image.jpg
__________________
Original, 102, 1782, #1 and #2 cart, PECO yard vac
  #10  
Old 09-07-2015, 06:20 PM
Jeff in Pa's Avatar
Jeff in Pa Jeff in Pa is offline
Grand Member
 
Join Date: Feb 2012
Location: Zionsville, PA
Posts: 2,793
Default

Creeper handle - $35 plus shipping
WF shown -- Will make narrow frame long ( tall tunnel )as shown for same price. If you want short tunnel handle with extension, $43 plus shipping for both. $10 for just the extension




~~~~~~~~~~~~~~~~~~~~~~

Creeper Poppet Indent Lever - $15 each plus shipping


~~~~~~~~~~~~~~~~~~~~~~

Brake Pivots for NF manual trans
Large pin, small pin & hex head adjustment bolt $25 plus shipping



~~~~~~~~~~~~~~~~~~~~~~~~~

Axle Pins for NF & WF - $15 plus shipping

Closed Thread

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 05:16 AM.


Powered by vBulletin® Version 3.8.0
Copyright ©2000 - 2018, Jelsoft Enterprises Ltd.

Cub Cadet is a premium line of outdoor power equipment, established in 1961 as part of International Harvester. During the 1960s, IH initiated an entirely new line of lawn and garden equipment aimed at the owners rural homes with large yards and private gardens. There were a wide variety of Cub Cadet branded and after-market attachments available; including mowers, blades, snow blowers, front loaders, plows, carts, etc. Cub Cadet advertising at that time harped on their thorough testing by "boys - acknowledged by many as the world's worst destructive force!". Cub Cadets became known for their dependability and rugged construction.

MTD Products, Inc. of Cleveland, Ohio purchased the Cub Cadet brand from International Harvester in 1981. Cub Cadet was held as a wholly owned subsidiary for many years following this acquisition, which allowed them to operate independently. Recently, MTD has taken a more aggressive role and integrated Cub Cadet into its other lines of power equipment.

This website and forum are not affiliated with or sponsored by MTD Products Inc, which owns the CUB CADET trademarks. It is not an official MTD Products Inc, website, and MTD Products Inc, is not responsible for any of its content. The official MTD Products Inc, website can be found at: http://www.mtdproducts.com. The information and opinions expressed on this website are the responsibility of the website's owner and/or it's members, & do not represent the opinions of MTD Products Inc. IH®, INTERNATIONAL HARVESTER® are registered trademark of CNH America LLC

All material, images, and graphics from this site are the property of www.onlycubcadets.net. Any unauthorized use, reproductions, or duplications are prohibited unless solely expressed in writing.

Cub Cadet, Cub, Cadet, IH, MTD, Parts, Tractors, Tractor, International Harvester, Lawn, Garden, Lawn Mower, Kohler, garden tractor equipment, lawn garden tractors, antique garden tractors, garden tractor, PTO, parts, online, Original, 70, 71, 72, 73, 76, SO76, 80, 81, 86, 100, 102, 104, 105, 106, 107, 108,109, 122, 123, 124, 125, 126, 127, 128, 129, 147, 149, 169, 182, 282, 382, 482, 580, 582, 582 Special, 680, 682, 782, 782D, 784, 800, 805, 882, 982, 984, 986, 1000, 1015, 1100, 1105, 1110, 1200, 1250, 1282, 1450, 1512, 1604, 1605, 1606, 1610, 1615, 1620, 1650, 1710, 1711, 1712, 1806, 1810, 1811, 1812, 1912, 1914.