PLEASE PATRONIZE OUR SPONSORS!
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
1320 PTO belt will not stop
Hi,
I have a 1320 in well maintained condition. It has the newer style front deck bracket that makes the deck 'fore and aft' adjustable. I have a properly sized belt, my tensioner is clean, greased and operates freely. My deck brake is maintained, adjusted and works properly. Even with the deck adjusted to make the belt extremely loose, when I pull the disengage lever the belt stops, I hear the brake grab, the blades stop. But then the belt slowly starts moving with enough pull to override the brake. I have even cleaned and sanded the drive pulley with successively finer emory cloth till it was polished so smooth I wondered if it would even pull the belt ( it does ). It slipped bad enough the other day when I was using the tractor to haul a wagon and not cutting grass that the brake started smoking. I put on a new belt and it still persists. This is a development this season that has not happened in all the years I've previously cut grass with it. Any suggestions? |
#2
|
|||
|
|||
Sounds like this is an issue with the pto not disengaging to me. I think thats where I would look first.
Randy
__________________
2 original cub cadets 1 100's 2 149's 1 73 1 2182 |
#3
|
||||
|
||||
The PTO belt guide must be installed correctly. It "corrals" the belt on the sides and keeps it from gripping the drive pulley.
__________________
Queen Of The Quietlines! |
#4
|
|||
|
|||
PTO belt
Randy and Delta.
Thank you for replying. The idler pulley mechanism fully retracts and the belt is very loose. I have even tried adjusting it to be so loose that even once fully engaged it was still loose enough that it "flapped". Yet, somehow the drive pulley is still pulling the belt. I just replaced belt guide on the idler pulley and it is properly positioned and the drive belt guide is not adjustable. I have replaced the spring on the deck brake to be sure the brake was pulling as tight as it should and the brake pad is not worn away, even though it was smoking and it grips tight. It is very perplexing to me and I am a very capable mechanic. I was hoping that maybe someone had possibly encountered this before and had a solution or some some specific instructions for correcting this. Am I correct in my presumption that the drive pulley needs to be smooth so as to be able to spin without pulling the belt when it is disengaged since the belt still resides on the pulley even when disengaged? Also, is there a guide to indicate how much slack should be in the belt when disengaged and how much tension should be in the belt once engaged? I do not see this in my manual. |
#5
|
||||
|
||||
If the the belt guide is distorted and allows the belt to sway out on the sides of the drive pulley, it will be driven by the pulley. The guide must keep the belt close to the "sides" of the pulley and away from where it curves around and engages the engine driven pulley. Clear as mud?
__________________
Queen Of The Quietlines! |
#6
|
|||
|
|||
Thank you, I'll take a closer look at that
|
|
|
Cub Cadet is a premium line of outdoor power equipment, established in 1961 as part of International Harvester. During the 1960s, IH initiated an entirely new line of lawn and garden equipment aimed at the owners rural homes with large yards and private gardens. There were a wide variety of Cub Cadet branded and after-market attachments available; including mowers, blades, snow blowers, front loaders, plows, carts, etc. Cub Cadet advertising at that time harped on their thorough testing by "boys - acknowledged by many as the world's worst destructive force!". Cub Cadets became known for their dependability and rugged construction.
MTD Products, Inc. of Cleveland, Ohio purchased the Cub Cadet brand from International Harvester in 1981. Cub Cadet was held as a wholly owned subsidiary for many years following this acquisition, which allowed them to operate independently. Recently, MTD has taken a more aggressive role and integrated Cub Cadet into its other lines of power equipment.
This website and forum are not affiliated with or sponsored by MTD Products Inc, which owns the CUB CADET trademarks. It is not an official MTD Products Inc, website, and MTD Products Inc, is not responsible for any of its content. The official MTD Products Inc, website can be found at: http://www.mtdproducts.com. The information and opinions expressed on this website are the responsibility of the website's owner and/or it's members, and do not represent the opinions of MTD Products Inc. IH, INTERNATIONAL HARVESTER are registered trademark of CNH America LLC
All material, images, and graphics from this site are the property of www.onlycubcadets.net. Any unauthorized use, reproductions, or duplications are prohibited unless solely expressed in writing.
Cub Cadet, Cub, Cadet, IH, MTD, Parts, Tractors, Tractor, International Harvester, Lawn, Garden, Lawn Mower, Kohler, garden tractor equipment, lawn garden tractors, antique garden tractors, garden tractor, PTO, parts, online, Original, 70, 71, 72, 73, 76, SO76, 80, 81, 86, 100, 102, 104, 105, 106, 107, 108,109, 122, 123, 124, 125, 126, 127, 128, 129, 147, 149, 169, 182, 282, 382, 482, 580, 582, 582 Special, 680, 682, 782, 782D, 784, 800, 805, 882, 982, 984, 986, 1000, 1015, 1100, 1105, 1110, 1200, 1250, 1282, 1450, 1512, 1604, 1605, 1606, 1610, 1615, 1620, 1650, 1710, 1711, 1712, 1806, 1810, 1811, 1812, 1912, 1914.