Only Cub Cadets

PLEASE PATRONIZE OUR SPONSORS!

CC Speciaalties R. F. Houtz and Sons

Patton Acres IH Cub Cadet Parts

Cub Cadet Parts & Service


If you would like to help maintain this site & enhance it, feel free to donate whatever amount you would like to!




Attention Folks we have a new owner!
Greg Rozar AKA- CubDieselFan


Go Back   Only Cub Cadets > Cub Cadets > CCC/MTD Cub Cadet built Tractors (GT)

Notices

Reply
 
Thread Tools Display Modes
  #11  
Old 06-20-2013, 09:09 AM
FrankF3's Avatar
FrankF3 FrankF3 is offline
Senior Member
 
Join Date: Aug 2011
Location: Massachusetts
Posts: 724
Default

Ken6x6, I used a Cub Cadet # 710-3220 from my dealer. It is a 1/4-20 x 1.0 GR5 bolt with lock-tite patch already pre-applied. You could get by with the same size bolt from the hardware store and apply your own lock-tite. I also used the belleville washer that Cub Cadet specs out - 736-0270, .265 x .75 x .062 thk.
__________________
1989 - Cub Cadet 1772
1987 - Cub Cadet 1572 w/Rear PTO & Cat. 0
38" Lawn Sweeper #196483
42" L42 (Bush Hog) Rotary Cutter # 190349
45" 2-Stage Snowblower # 196364
48" Haban Rotortiller Rear PTO Driven #190356
54" SnowBlade with hydraulic Angle #196376
60" Haban Mowing Deck #196374
Reply With Quote
  #12  
Old 06-20-2013, 04:45 PM
hhc70 hhc70 is offline
Member
 
Join Date: Mar 2010
Location: Ontario
Posts: 48
Default

Quote:
Originally Posted by Sam Mac View Post
I have a 1772 sitting in my shop that I can use to see if this will play. I have the crank adapter and a pump adapter. When you get a second see if you can get me an overall length of the shaft with the CV joints on it compressed to it's shortest length. As near as I can tell the space between the flanges of the adapters is 20.625"
I measure 20" even from end to end fully compressed.
Reply With Quote
  #13  
Old 06-20-2013, 08:34 PM
ken6x6's Avatar
ken6x6 ken6x6 is offline
Senior Member
 
Join Date: Apr 2012
Location: New Jersey
Posts: 586
Default

ok thanks frank, im waiting for you to beat the crap out of this drive shaft so i can get mine.
__________________
127 - 48'' deck + tiller.
1512- 46" GT deck & bagger
1872- 60" Haban
1772 turbo diesel- Iron rear + KW loader + backhoe + 3 point.
Case 580CK
Ford 850
International TD-8E
Reply With Quote
  #14  
Old 06-21-2013, 02:30 PM
Sam Mac's Avatar
Sam Mac Sam Mac is offline
Administrator
 
Join Date: Feb 2010
Location: Galax VA
Posts: 18,745
Default 1772 & 1572 drive shafts

Ok guys BIG thanks to Leadslingingdaddy he sent me a drive shaft from an 1863 it looks like it will work as a replacement for the drive shaft in the 1572 & 1772 as long as you have the Cyclops engine and pump adapters but both are NLA from Cub. I can have them made for you or can see if you can get them from the guys that part out Cubs. The 1863 shaft is 20.375” long fully compressed and the flange to flange measurement on the 1772 is 20.625” it may need a 1/8” spacer but I don’t think so. I need to check to see if the splines are fully engaged at 20.625”. Pics tomorrow.
__________________
2264 with 54 GT deck
1641 AKA Black Jack with a 402-E Haban Sickle bar mower
JD317 dump truck
BX2670 with FEL
Reply With Quote
  #15  
Old 06-21-2013, 02:37 PM
Sam Mac's Avatar
Sam Mac Sam Mac is offline
Administrator
 
Join Date: Feb 2010
Location: Galax VA
Posts: 18,745
Default

Quote:
Originally Posted by hhc70 View Post
Are these better than the cyclops series CV joints? I have an 1863/4 driveline waiting for a rainy day to go into my 1572.
hhc70

Looks like you are good to go as long as you have the adapter for the Kubota and the pump. Pics are the adapters my machine shop makes for me.
Attached Images
File Type: jpg 1772 2000c.jpg (20.2 KB, 767 views)
File Type: jpg IMG_2585s.jpg (30.0 KB, 765 views)
__________________
2264 with 54 GT deck
1641 AKA Black Jack with a 402-E Haban Sickle bar mower
JD317 dump truck
BX2670 with FEL
Reply With Quote
  #16  
Old 06-23-2013, 08:33 AM
ken6x6's Avatar
ken6x6 ken6x6 is offline
Senior Member
 
Join Date: Apr 2012
Location: New Jersey
Posts: 586
Default

Sam, i was driving out to see my grandmother in PA yesterday and on my way i saw a 105 for sale, i stopped and checked it out and the guy came out and we got to talking cubs. he walked me around back and showed me a pile of cub parts he was also selling. i saw a nice iron rear setting there and a few words and a hand shake later i was loading up that iron rear in my truck. im going to see if i cant get this thing under my 1772. im going to swap all the gears over too. lets hope your drive shaft works with iron and diesel.
__________________
127 - 48'' deck + tiller.
1512- 46" GT deck & bagger
1872- 60" Haban
1772 turbo diesel- Iron rear + KW loader + backhoe + 3 point.
Case 580CK
Ford 850
International TD-8E
Reply With Quote
  #17  
Old 06-23-2013, 10:50 AM
Sam Mac's Avatar
Sam Mac Sam Mac is offline
Administrator
 
Join Date: Feb 2010
Location: Galax VA
Posts: 18,745
Default

Quote:
Originally Posted by ken6x6 View Post
Sam, i was driving out to see my grandmother in PA yesterday and on my way i saw a 105 for sale, i stopped and checked it out and the guy came out and we got to talking cubs. he walked me around back and showed me a pile of cub parts he was also selling. i saw a nice iron rear setting there and a few words and a hand shake later i was loading up that iron rear in my truck. im going to see if i cant get this thing under my 1772. im going to swap all the gears over too. lets hope your drive shaft works with iron and diesel.
Ken

You may want to take the time to read this thread, looks like the cast rear has a clearance issue with the fuel tank.
http://www.onlycubcadets.net/forum/s...t=23475&page=4

Drive shaft should be no problem iron or alum.
__________________
2264 with 54 GT deck
1641 AKA Black Jack with a 402-E Haban Sickle bar mower
JD317 dump truck
BX2670 with FEL
Reply With Quote
  #18  
Old 06-23-2013, 01:44 PM
Sam Mac's Avatar
Sam Mac Sam Mac is offline
Administrator
 
Join Date: Feb 2010
Location: Galax VA
Posts: 18,745
Default

Quote:
Originally Posted by hhc70 View Post
Are these better than the cyclops series CV joints? I have an 1863/4 driveline waiting for a rainy day to go into my 1572.
hhc70

I got a chance to check out that 1863 shaft today. You will need a 1/4" spacer to make it work. If you put it in as it is the splines will not fully engage the ball in the center of the CV joint.
__________________
2264 with 54 GT deck
1641 AKA Black Jack with a 402-E Haban Sickle bar mower
JD317 dump truck
BX2670 with FEL
Reply With Quote
  #19  
Old 06-23-2013, 05:55 PM
hhc70 hhc70 is offline
Member
 
Join Date: Mar 2010
Location: Ontario
Posts: 48
Default

I think I can handle that. If I didn't have the engine adapter, I guess I would make one 1/4" longer.
Reply With Quote
  #20  
Old 06-23-2013, 06:59 PM
ken6x6's Avatar
ken6x6 ken6x6 is offline
Senior Member
 
Join Date: Apr 2012
Location: New Jersey
Posts: 586
Default

i have read about the fuel tank issues. seems like its just the valve that gets in the way. ill make something work.
__________________
127 - 48'' deck + tiller.
1512- 46" GT deck & bagger
1872- 60" Haban
1772 turbo diesel- Iron rear + KW loader + backhoe + 3 point.
Case 580CK
Ford 850
International TD-8E
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 04:31 PM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.

Cub Cadet is a premium line of outdoor power equipment, established in 1961 as part of International Harvester. During the 1960s, IH initiated an entirely new line of lawn and garden equipment aimed at the owners rural homes with large yards and private gardens. There were a wide variety of Cub Cadet branded and after-market attachments available; including mowers, blades, snow blowers, front loaders, plows, carts, etc. Cub Cadet advertising at that time harped on their thorough testing by "boys - acknowledged by many as the world's worst destructive force!". Cub Cadets became known for their dependability and rugged construction.

MTD Products, Inc. of Cleveland, Ohio purchased the Cub Cadet brand from International Harvester in 1981. Cub Cadet was held as a wholly owned subsidiary for many years following this acquisition, which allowed them to operate independently. Recently, MTD has taken a more aggressive role and integrated Cub Cadet into its other lines of power equipment.

This website and forum are not affiliated with or sponsored by MTD Products Inc, which owns the CUB CADET trademarks. It is not an official MTD Products Inc, website, and MTD Products Inc, is not responsible for any of its content. The official MTD Products Inc, website can be found at: http://www.mtdproducts.com. The information and opinions expressed on this website are the responsibility of the website's owner and/or it's members, and do not represent the opinions of MTD Products Inc. IH, INTERNATIONAL HARVESTER are registered trademark of CNH America LLC

All material, images, and graphics from this site are the property of www.onlycubcadets.net. Any unauthorized use, reproductions, or duplications are prohibited unless solely expressed in writing.

Cub Cadet, Cub, Cadet, IH, MTD, Parts, Tractors, Tractor, International Harvester, Lawn, Garden, Lawn Mower, Kohler, garden tractor equipment, lawn garden tractors, antique garden tractors, garden tractor, PTO, parts, online, Original, 70, 71, 72, 73, 76, SO76, 80, 81, 86, 100, 102, 104, 105, 106, 107, 108,109, 122, 123, 124, 125, 126, 127, 128, 129, 147, 149, 169, 182, 282, 382, 482, 580, 582, 582 Special, 680, 682, 782, 782D, 784, 800, 805, 882, 982, 984, 986, 1000, 1015, 1100, 1105, 1110, 1200, 1250, 1282, 1450, 1512, 1604, 1605, 1606, 1610, 1615, 1620, 1650, 1710, 1711, 1712, 1806, 1810, 1811, 1812, 1912, 1914.