PLEASE PATRONIZE OUR SPONSORS!
|
|
Thread Tools | Display Modes |
#11
|
|||
|
|||
related question
I am working on a 1811 and the remote filter lines don't leak. However where the steel switch to rubber the hoses will spin on the steel is that normal? Can you buy an adapter that will replace the line adapter at the motor and change to a spin on filter? I did have a m18 on another tractor that was this way, it should be possible to find a motor side panel or out it out for the filter. Would this cause a cooling issue because of the change?
|
#12
|
|||
|
|||
Quote:
As long as you don't have any leaks, don't worry about the hose spinning where it meets the steel line. It's not a very tight crimp. |
#13
|
|||
|
|||
I'm sure your right on the frame rail. Didn't think of that when the engine is out on the bench. Good thing is it is easy to inspect for leaks and not real hard project to change hoses if they do leak. Thanks for the advise.
|
#14
|
||||
|
||||
Just saw this post but I installed the block mounted oil filter adapter on one of my 782s. I notched the engine tins for clearance (which as I remember was just the piece that covers the head; I don't recall any change to the forward piece). It makes fitting the side panel snug but it will clear. I've been using the Napa equivalent filter (I can't recall the number). I use one of those 3-finger type filter wrenches to unscrew it. Pulling the filter off obviously requires a piece of cardboard to funnel the oil away.
__________________
RUN IN THE RED 782 w/50c deck (red); 782 dual stick, 44c deck (y/w); 1050 w/38c deck; 1864 w/54" GT deck; 1872 project Cub Cadet Pro Z 560 L 42" power angle snowblade, #2 tiller, 2-QA42a snowthrowers, 450 thrower, #2 cart; 54" Haban blade; Brinly box blade, 48" dethatcher, moldboard plow; Agri-Fab sweeper 1200, 1863, 1864 parts machines |
#15
|
|||
|
|||
Quote:
Up there on the back of the fuel tank where they mounted it remotely is a joke too. Always need something to catch the oil there too. |
#16
|
||||
|
||||
Yeah those remote lines are a pain. They leak on my 1861 too. I found the block mounted adapter on ebay a couple years back so I thought I'd try it. I'd have to fiddle with it more but I think my side panel tight fit is more a result of my trimming of the tins than anything. There is no contact to the oil filter by the frame, the panel, or the tins.
__________________
RUN IN THE RED 782 w/50c deck (red); 782 dual stick, 44c deck (y/w); 1050 w/38c deck; 1864 w/54" GT deck; 1872 project Cub Cadet Pro Z 560 L 42" power angle snowblade, #2 tiller, 2-QA42a snowthrowers, 450 thrower, #2 cart; 54" Haban blade; Brinly box blade, 48" dethatcher, moldboard plow; Agri-Fab sweeper 1200, 1863, 1864 parts machines |
Thread Tools | |
Display Modes | |
|
|
Cub Cadet is a premium line of outdoor power equipment, established in 1961 as part of International Harvester. During the 1960s, IH initiated an entirely new line of lawn and garden equipment aimed at the owners rural homes with large yards and private gardens. There were a wide variety of Cub Cadet branded and after-market attachments available; including mowers, blades, snow blowers, front loaders, plows, carts, etc. Cub Cadet advertising at that time harped on their thorough testing by "boys - acknowledged by many as the world's worst destructive force!". Cub Cadets became known for their dependability and rugged construction.
MTD Products, Inc. of Cleveland, Ohio purchased the Cub Cadet brand from International Harvester in 1981. Cub Cadet was held as a wholly owned subsidiary for many years following this acquisition, which allowed them to operate independently. Recently, MTD has taken a more aggressive role and integrated Cub Cadet into its other lines of power equipment.
This website and forum are not affiliated with or sponsored by MTD Products Inc, which owns the CUB CADET trademarks. It is not an official MTD Products Inc, website, and MTD Products Inc, is not responsible for any of its content. The official MTD Products Inc, website can be found at: http://www.mtdproducts.com. The information and opinions expressed on this website are the responsibility of the website's owner and/or it's members, and do not represent the opinions of MTD Products Inc. IH, INTERNATIONAL HARVESTER are registered trademark of CNH America LLC
All material, images, and graphics from this site are the property of www.onlycubcadets.net. Any unauthorized use, reproductions, or duplications are prohibited unless solely expressed in writing.
Cub Cadet, Cub, Cadet, IH, MTD, Parts, Tractors, Tractor, International Harvester, Lawn, Garden, Lawn Mower, Kohler, garden tractor equipment, lawn garden tractors, antique garden tractors, garden tractor, PTO, parts, online, Original, 70, 71, 72, 73, 76, SO76, 80, 81, 86, 100, 102, 104, 105, 106, 107, 108,109, 122, 123, 124, 125, 126, 127, 128, 129, 147, 149, 169, 182, 282, 382, 482, 580, 582, 582 Special, 680, 682, 782, 782D, 784, 800, 805, 882, 982, 984, 986, 1000, 1015, 1100, 1105, 1110, 1200, 1250, 1282, 1450, 1512, 1604, 1605, 1606, 1610, 1615, 1620, 1650, 1710, 1711, 1712, 1806, 1810, 1811, 1812, 1912, 1914.