PLEASE PATRONIZE OUR SPONSORS!
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
44c spindle rebuild
I'm having troubles uploading pictures from my phone, sorry. I have a 44c with water pump style bearings. one of the bearings is REALLY bad, the other 2 are not so bad. Upon taking them apart, the one that's really bad was rebuilt by previous owner with a plastic looking seal on both ends. The other 2 have metal seals and a small rubber/spring seal that sits between the spacer and metal seal. I'm guessing the bad bearing with the plastic seal wasn't rebuilt correctly? Anyone know the correct part number for the metal seals to rebuild these?
Thanks! Gabe |
#2
|
|||
|
|||
44c spindle rebuild
Thanks R Bedell for the reply. I might have misspoke when I called it a water pump style bearing. I've attached a picture of the bearing I'm talking about. I believe it's the rebuildable style. The seal in the picture is the metal style seal that I'd like to use on the rebuild. I've been seeing the plastic/rubber style seal for sale online. I'm hoping to find a metal style. Does anyone know the part number for the metal style seal? Has anyone rebuilt these and does anyone have a preference as to one or the other types of seals?
Thanks, Gabe |
#3
|
|||
|
|||
Here's a pic of the plastic style seal that has failed. I'm assuming this one's been rebuilt once before because the other two spindle have the metal style seals and are not that sloppy. This one is really bad...
Thanks! |
#4
|
|||
|
|||
The "rubber" seal is just rubber coated. Still has a steel backing. As long as it's installed properly, and has the dust cover between the blade and the seal (large cup that goes up and over the housing) either seal will be fine. It's no big deal to get a steel housing seal. Just do it by size. ID/OD/THK. Make sure to install it upside down or you will blow it out when greasing.
Your understanding of the metal seal is wrong also. Quote:
|
#5
|
|||
|
|||
Bearing seal install
J-mech,
You posted to this thread a while back about installing the seal upside down, I just wanted to confirm that you meant to install the seal with the flat part toward the center of the bearing (please see attached photo). Do I do this on both sides of the bearing? I now have five used bearings for this deck and another deck I'm working on. All the seals are installed four different ways between all five bearings. Thanks Gabe |
#6
|
|||
|
|||
Yes, install it like you show, but only on the bottom seal. If you do it on the top, grease will spit out and get on the belt. Don't want that!
|
#7
|
||||
|
||||
The number for the CR seal is 12386. They were on the bottom of my 1863. The tractor was my dads and no one had ever been into the spindles.
__________________
1572, 1864 x2, 1810 x2, 1863 & GT1554(Dad's Ole Mowers), 1811,782D, 1872 x2, 782DT(Sold), 3235, 1860, 1772 with 3-point and Turbo. |
#8
|
|||
|
|||
Got it, great! Thank you guys for the responses.
|
|
|
Cub Cadet is a premium line of outdoor power equipment, established in 1961 as part of International Harvester. During the 1960s, IH initiated an entirely new line of lawn and garden equipment aimed at the owners rural homes with large yards and private gardens. There were a wide variety of Cub Cadet branded and after-market attachments available; including mowers, blades, snow blowers, front loaders, plows, carts, etc. Cub Cadet advertising at that time harped on their thorough testing by "boys - acknowledged by many as the world's worst destructive force!". Cub Cadets became known for their dependability and rugged construction.
MTD Products, Inc. of Cleveland, Ohio purchased the Cub Cadet brand from International Harvester in 1981. Cub Cadet was held as a wholly owned subsidiary for many years following this acquisition, which allowed them to operate independently. Recently, MTD has taken a more aggressive role and integrated Cub Cadet into its other lines of power equipment.
This website and forum are not affiliated with or sponsored by MTD Products Inc, which owns the CUB CADET trademarks. It is not an official MTD Products Inc, website, and MTD Products Inc, is not responsible for any of its content. The official MTD Products Inc, website can be found at: http://www.mtdproducts.com. The information and opinions expressed on this website are the responsibility of the website's owner and/or it's members, and do not represent the opinions of MTD Products Inc. IH, INTERNATIONAL HARVESTER are registered trademark of CNH America LLC
All material, images, and graphics from this site are the property of www.onlycubcadets.net. Any unauthorized use, reproductions, or duplications are prohibited unless solely expressed in writing.
Cub Cadet, Cub, Cadet, IH, MTD, Parts, Tractors, Tractor, International Harvester, Lawn, Garden, Lawn Mower, Kohler, garden tractor equipment, lawn garden tractors, antique garden tractors, garden tractor, PTO, parts, online, Original, 70, 71, 72, 73, 76, SO76, 80, 81, 86, 100, 102, 104, 105, 106, 107, 108,109, 122, 123, 124, 125, 126, 127, 128, 129, 147, 149, 169, 182, 282, 382, 482, 580, 582, 582 Special, 680, 682, 782, 782D, 784, 800, 805, 882, 982, 984, 986, 1000, 1015, 1100, 1105, 1110, 1200, 1250, 1282, 1450, 1512, 1604, 1605, 1606, 1610, 1615, 1620, 1650, 1710, 1711, 1712, 1806, 1810, 1811, 1812, 1912, 1914.