Only Cub Cadets

PLEASE PATRONIZE OUR SPONSORS!

CC Speciaalties R. F. Houtz and Sons

Patton Acres IH Cub Cadet Parts

Cub Cadet Parts & Service


If you would like to help maintain this site & enhance it, feel free to donate whatever amount you would like to!




Attention Folks we have a new owner!
Greg Rozar AKA- CubDieselFan


Go Back   Only Cub Cadets > Cub Cadets > Home Made

Notices

Reply
 
Thread Tools Display Modes
  #11  
Old 08-16-2013, 01:14 PM
ccr147 ccr147 is offline
Member
 
Join Date: Sep 2010
Location: Pennsylvania
Posts: 42
Default

Well based on that picture I'm thinking I might have just enough room to put a shaft coupler on there and moung the pump above that access plate or just behind it. One thing I just thought of is I don't know what the rpm of the output shaft is in relation or the rpm of the motor. I would assume 1:1 but thats just a guess.

Curt
Reply With Quote
  #12  
Old 08-16-2013, 07:16 PM
J-Mech J-Mech is offline
Banned
 
Join Date: Apr 2013
Location: Oblong, Illinois
Posts: 17,594
Default

If you could align the shaft, you MAYBE could to it. Yes that shaft runs engine RPM.

Here are the issues:
1.) Reservoir
2.) System relief
3.) What are you going to do with the pump when not in use
4.) Max pump input shaft speed.
5.) Aligning the shaft
6.) Clearance with the fenders

I really think this would be a difficult build. If you want to do something like this, I'd suggest running it off the front PTO. It would be MUCH simpler. And it can be easily removed when not in use.
Reply With Quote
  #13  
Old 08-16-2013, 10:17 PM
bruce s's Avatar
bruce s bruce s is offline
Senior Member
 
Join Date: Aug 2010
Location: Iowa
Posts: 161
Default

CCR147 I have seen this done before and I believe the pump was mounted just behind the back of the tranny . The hydraulic valves were under the seat , not sure where the tank was unless he used the tranny oil . I do remember it was a square fendered tractor like a 125 maybe. Surplus center is a good place to get parts for a job like this .
Reply With Quote
  #14  
Old 08-16-2013, 11:03 PM
ccr147 ccr147 is offline
Member
 
Join Date: Sep 2010
Location: Pennsylvania
Posts: 42
Default

The pump will always be in use. It'll power the deck lift and hitch lift and any other accessories that may use hydraulics. It's a 3600 rpm pump, it's intended to be connected to a small engine. I may have to modify the "tool box" under the seat to make it fit, we'll see. Though I would like to use that space for a reservoir, but that could go somewhere else of course. Getting the shaft lined up should really be a matter of fabricating a bracket to properly place the pump. Assuming clearance isn't an issue.

Bruce I sure wish I could see pictures of that build or pick his brain.

Speaking of putting the pump on the front, I wish I could but then I'd be converting the deck to a hydraulic drive and that gets expensive quick.

Curt
Reply With Quote
  #16  
Old 08-16-2013, 11:09 PM
fourinchdragslicks fourinchdragslicks is offline
Senior Member
 
Join Date: Oct 2012
Location: Missouri
Posts: 197
Default

here is another one:
http://www.ihcubcadet.com/forum/messages/106/22474.jpg
Reply With Quote
  #17  
Old 08-16-2013, 11:34 PM
J-Mech J-Mech is offline
Banned
 
Join Date: Apr 2013
Location: Oblong, Illinois
Posts: 17,594
Default

Well, there ya go! Pics and all!
Reply With Quote
  #18  
Old 08-18-2013, 10:39 AM
bruce s's Avatar
bruce s bruce s is offline
Senior Member
 
Join Date: Aug 2010
Location: Iowa
Posts: 161
Default

I'm not sure that was the one I saw but it would work. Do a forum search for hydraulics at the top of the page , there are a lot of good ideas .
Reply With Quote
  #19  
Old 08-29-2013, 02:39 PM
mrjeep81's Avatar
mrjeep81 mrjeep81 is offline
Senior Member
 
Join Date: Oct 2009
Location: Ohio
Posts: 347
Default maybe like this

I've seen this one a lot. 2012-07-02_16-17-37_318.jpg

2012-07-02_15-55-01_63.jpg

2012-06-29_16-22-05_794.jpg
__________________
1450SGT
1641
528 SWE Snowblower,
Reply With Quote
  #20  
Old 08-29-2013, 05:10 PM
Maple Cabin's Avatar
Maple Cabin Maple Cabin is offline
Member
 
Join Date: Sep 2012
Location: Ontario
Posts: 71
Default Log splitter attament

Yes it all doable but if that becomes your power source for any remove device aka splitter etc. then the tractor is tied to that. Even in a one man show it would be a pain in the but to couple and uncouple hose to haul a trailer full. My Log splitter is directly coupled to 6.5HP engine (yes another engine) which is at idle most of the. Now the tractor is free for other things like hauling. A ported pump would do anything on the tractor that would ever need it to do.

My 22 Ton speedco splitter has 4-5 gal tank and does get warm when running for a few hours.
__________________
Doug
126 Creeper,H lift,Deck, Sleeve hitch, B Plow, Weights
129 Deck, Blade, Weights
1200 Creeper Deck: 1250 B Tiller odd deck
782R with power steering

JD 110H:JD 112H
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 05:51 PM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.

Cub Cadet is a premium line of outdoor power equipment, established in 1961 as part of International Harvester. During the 1960s, IH initiated an entirely new line of lawn and garden equipment aimed at the owners rural homes with large yards and private gardens. There were a wide variety of Cub Cadet branded and after-market attachments available; including mowers, blades, snow blowers, front loaders, plows, carts, etc. Cub Cadet advertising at that time harped on their thorough testing by "boys - acknowledged by many as the world's worst destructive force!". Cub Cadets became known for their dependability and rugged construction.

MTD Products, Inc. of Cleveland, Ohio purchased the Cub Cadet brand from International Harvester in 1981. Cub Cadet was held as a wholly owned subsidiary for many years following this acquisition, which allowed them to operate independently. Recently, MTD has taken a more aggressive role and integrated Cub Cadet into its other lines of power equipment.

This website and forum are not affiliated with or sponsored by MTD Products Inc, which owns the CUB CADET trademarks. It is not an official MTD Products Inc, website, and MTD Products Inc, is not responsible for any of its content. The official MTD Products Inc, website can be found at: http://www.mtdproducts.com. The information and opinions expressed on this website are the responsibility of the website's owner and/or it's members, and do not represent the opinions of MTD Products Inc. IH, INTERNATIONAL HARVESTER are registered trademark of CNH America LLC

All material, images, and graphics from this site are the property of www.onlycubcadets.net. Any unauthorized use, reproductions, or duplications are prohibited unless solely expressed in writing.

Cub Cadet, Cub, Cadet, IH, MTD, Parts, Tractors, Tractor, International Harvester, Lawn, Garden, Lawn Mower, Kohler, garden tractor equipment, lawn garden tractors, antique garden tractors, garden tractor, PTO, parts, online, Original, 70, 71, 72, 73, 76, SO76, 80, 81, 86, 100, 102, 104, 105, 106, 107, 108,109, 122, 123, 124, 125, 126, 127, 128, 129, 147, 149, 169, 182, 282, 382, 482, 580, 582, 582 Special, 680, 682, 782, 782D, 784, 800, 805, 882, 982, 984, 986, 1000, 1015, 1100, 1105, 1110, 1200, 1250, 1282, 1450, 1512, 1604, 1605, 1606, 1610, 1615, 1620, 1650, 1710, 1711, 1712, 1806, 1810, 1811, 1812, 1912, 1914.