Only Cub Cadets

PLEASE PATRONIZE OUR SPONSORS!

CC Speciaalties R. F. Houtz and Sons

Patton Acres IH Cub Cadet Parts

Cub Cadet Parts & Service


If you would like to help maintain this site & enhance it, feel free to donate whatever amount you would like to!




Attention Folks we have a new owner!
Greg Rozar AKA- CubDieselFan


Go Back   Only Cub Cadets > Cub Cadets > Implements and Attachments

Notices

Reply
 
Thread Tools Display Modes
  #41  
Old 11-24-2014, 11:08 AM
darkminion_17's Avatar
darkminion_17 darkminion_17 is offline
Grand Member
 
Join Date: Aug 2010
Location: New Jersey
Posts: 10,984
Default

Looks good,what bracket did you make to attach to the rockshaft?
__________________
Up to 530 and counting...
I give up updating my profile!
Reply With Quote
  #42  
Old 11-24-2014, 11:22 AM
finsruskw finsruskw is offline
Grand Member
 
Join Date: Mar 2013
Location: Iowa
Posts: 2,984
Talking

The U shaped one with the one leg longer that takes the spacer over the pin. Real PITA to make. I only made 2 of 'em and they are both on tractors now. Made one by heating and bending and tried to fab the other out of 3 pieces of flat stock. It was somewhat easier than having to bend the stock. Real PITA if you don't have a helper to control and operate the torch while you make the bends.

Sure ain't worth burnin' the place down for!!!
Reply With Quote
  #43  
Old 11-24-2014, 11:32 AM
red56turbo's Avatar
red56turbo red56turbo is offline
Grand Member
 
Join Date: Jan 2011
Location: Iowa
Posts: 2,523
Default

Quote:
Originally Posted by finsruskw View Post
Looks like the overall length of the rod including the bends is about 16.25", straight line.

I used an original rod and welded up a temporary jig on the welding table to get the bends the same and the placement of the holes correct, then made the bends, using a length of 1/2" round, leaving a little extra on each end so I could trim to fit.

The bends (approx. 155*), are centered 3" in from the center of the holes which I made at 5/16" maybe a little more.
The straight line between the holes is approx. 9.5"

I cut some small pieces of 3/8" x 3/4" flat into 3/4" squares for the ends and welded them to the bent rod after adjusting the length to match the original using the jig as a guide for pacing them.
Drill the holes in these pieces before cutting.

If you could visualize drawing a straight line thru the center of the holes, from this line to the upper side of the long part of the 1/2 round is approx. 1-5/8".

I hope this is understandable!!
Dave,
Nice job! You'll have to let us know how they work out for ya.
__________________
Josh

Diesel Cub Cadets...........
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 05:21 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.

Cub Cadet is a premium line of outdoor power equipment, established in 1961 as part of International Harvester. During the 1960s, IH initiated an entirely new line of lawn and garden equipment aimed at the owners rural homes with large yards and private gardens. There were a wide variety of Cub Cadet branded and after-market attachments available; including mowers, blades, snow blowers, front loaders, plows, carts, etc. Cub Cadet advertising at that time harped on their thorough testing by "boys - acknowledged by many as the world's worst destructive force!". Cub Cadets became known for their dependability and rugged construction.

MTD Products, Inc. of Cleveland, Ohio purchased the Cub Cadet brand from International Harvester in 1981. Cub Cadet was held as a wholly owned subsidiary for many years following this acquisition, which allowed them to operate independently. Recently, MTD has taken a more aggressive role and integrated Cub Cadet into its other lines of power equipment.

This website and forum are not affiliated with or sponsored by MTD Products Inc, which owns the CUB CADET trademarks. It is not an official MTD Products Inc, website, and MTD Products Inc, is not responsible for any of its content. The official MTD Products Inc, website can be found at: http://www.mtdproducts.com. The information and opinions expressed on this website are the responsibility of the website's owner and/or it's members, and do not represent the opinions of MTD Products Inc. IH, INTERNATIONAL HARVESTER are registered trademark of CNH America LLC

All material, images, and graphics from this site are the property of www.onlycubcadets.net. Any unauthorized use, reproductions, or duplications are prohibited unless solely expressed in writing.

Cub Cadet, Cub, Cadet, IH, MTD, Parts, Tractors, Tractor, International Harvester, Lawn, Garden, Lawn Mower, Kohler, garden tractor equipment, lawn garden tractors, antique garden tractors, garden tractor, PTO, parts, online, Original, 70, 71, 72, 73, 76, SO76, 80, 81, 86, 100, 102, 104, 105, 106, 107, 108,109, 122, 123, 124, 125, 126, 127, 128, 129, 147, 149, 169, 182, 282, 382, 482, 580, 582, 582 Special, 680, 682, 782, 782D, 784, 800, 805, 882, 982, 984, 986, 1000, 1015, 1100, 1105, 1110, 1200, 1250, 1282, 1450, 1512, 1604, 1605, 1606, 1610, 1615, 1620, 1650, 1710, 1711, 1712, 1806, 1810, 1811, 1812, 1912, 1914.