PLEASE PATRONIZE OUR SPONSORS!
#11
|
||||
|
||||
Looks like fun, rescue, bet the insulation panels were pricey but it makes for fast installation.
I like the guy with the joystick pumping the perishable product.
__________________
Up to 530 and counting... I give up updating my profile! |
#12
|
||||
|
||||
Rescue, thanks for the pics. I have a few questions on your install.
--What is the foam board you used and what is the cost? I looked at the 2" pink board at Home Cheapo and it is $36 for a 4x8 sheet. My slab is going to be 2400sf so I will need 75 sheets. --What is it that you put up against the footer? I think all I have seen on the vids is that they run the 2" foam up to the top of the crete. I didn't think that looked right. --Do I need 2" or could I use 1" at half the cost? I'm thinking probably 2" is the way to go. --Did you put a vapor barrier down? --I've seen it put down like your job is and then some people say the pex has to be in the middle of the crete to work properly. Most vids I've seen show the pex on top of the rebar but I'm like you, wouldn't there be some type of problem over time with expansion and contraction? --Did you zone your job? --Do you think I need to use the 5/8 for my job or will the 1/2" work? --I will probably be using a propane tankless water heater for my source but I'm not sure what the codes say here for using them. I may be telling Mr. Inspector that the pex is for future use. Have you seen them used up your way? Thanks for all the input everyone. I'm sure I will have more questions.
__________________
This ain't no hobby....it's an addiction |
#13
|
||||
|
||||
Quote:
__________________
1- 1864 Dual hyd, cat 0, axle braces 1- 1450 Dual Stick w/ power steering 1- 1200 in pieces 1- 1864 in pieces QA36A Thrower, #1 Tiller w/ extensions, IH windbreaker, IH wheel weights, 44C mower deck, 50C mower deck, CCC 54" Blade, GT46 high vacuum deck, GT54 deck, Cub Tripple Bagger, Custom dozer blade, Custom suitcase weights, 3pt cultivator, lawn sweeper, original R-Bucket |
#14
|
||||
|
||||
Crap, this is the reply I got back from the Thermo-Snap rep. Well, looks like he was out for my best interest and not a sale. Kudos to him and his company. I guess I need to ask around what to use or can that idea.
His reply. Todd, Thanks for your inquiry about Thermo-Snap by Benchmark Foam. Full disclosure, according to IRC Building Code, the entire state of Georgia is considered "Very Heavy Termite infestation probability." The below statement is taken directly from the Code. R318.4 Foam Plastic Protection In areas where the probability of termite infestation is "very heavy" as indicated in Figure R301.2(6), extruded and expanded polystyrene, polyisocyanurate and other foam plastics shall not be installed on the exterior face or under interior or exterior foundation walls or slab foundations located below grade. The clearance between foam plastics installed above grade and exposed earth shall be not less than 6 inches (152 mm). Now I am not trying to discourage you from any building methods you want to try, but I want to have everything up front. If you are still interested in pricing, we would sell you directly but we would need to calculate a freight rate down to you. Which zip code would this be shipping to?? Is this a commercial, residential, or job site address? What kind of equipment is on hand to unload? If you can get back directly to me with those answers, I can calculate all in pricing with freight included. Once again, thanks for your interest in Thermo-Snap and let me know if you have any questions.
__________________
This ain't no hobby....it's an addiction |
#15
|
||||
|
||||
I may look into something like this if Mr. Inspector approves.
http://www.ecofoil.com/All-Products/...3ZdxoCDi_w_wcB
__________________
This ain't no hobby....it's an addiction |
#16
|
||||
|
||||
By no means discouraging your heating plan, just wondering why floor heat instead of a furnace of some sort? We probably get a little colder than you guys and I don't know of anyone with floor heating in their shop. Yes, I understand its really nice in the northern climates. Just wondering and learning as I have never seen or even heard of this around here.
__________________
2072 w/60" Haban 982 with 3 pt and 60" Haban 1811 with ags and 50C 124 w/hydraulic lift 782 w/mounted sprayer 2284 w/54" mowing deck |
#17
|
||||
|
||||
Quote:
I have heard that from inspectors up here in jersey, typically putting foam board, or fiber glass insulation board on exterior below grade walls is not code. I would go with a overhead radiant heat unit.
__________________
Up to 530 and counting... I give up updating my profile! |
#18
|
||||
|
||||
Nebraska allows it and some of the city's here have extreme codes bordering on insanity. However, different regions, different hurdles.
IF Radiant were not an option, I would want forced air w/98% afue and or heat pump, maybe even GEO... For a shiny new shop. Tube heaters are OK, not a big fan and never push them.
__________________
1- 1864 Dual hyd, cat 0, axle braces 1- 1450 Dual Stick w/ power steering 1- 1200 in pieces 1- 1864 in pieces QA36A Thrower, #1 Tiller w/ extensions, IH windbreaker, IH wheel weights, 44C mower deck, 50C mower deck, CCC 54" Blade, GT46 high vacuum deck, GT54 deck, Cub Tripple Bagger, Custom dozer blade, Custom suitcase weights, 3pt cultivator, lawn sweeper, original R-Bucket |
#19
|
||||
|
||||
Radiant floor heat in Georgia is pretty much non existent. It doesn't get cold enough to justify it. On one end of this building will be an 800sf apartment for my MIL. I hate carpet so it will probably have a lot of tile or similar for flooring and I know that she will be cold walking on an unheated floor. Her place will have a separate heat pump system for heat and a/c.
My shop area will also have a heat pump system for its primary heat & a/c also. I'm wanting to install the radiant because I think it's a good way to heat and would be cool to have. The cost isn't much for the oxygen barrier Pex either at $0.21/ft. I figured I would have a total of less than $700 in Pex pipe in the slab. I'm a commercial HVAC contractor so nothing will get subbed out. I will do it all myself at my own pace as time allows. If I had to pay out of pocket to have this done there would be no way I would ever think about it.
__________________
This ain't no hobby....it's an addiction |
#20
|
||||
|
||||
Quote:
__________________
1- 1864 Dual hyd, cat 0, axle braces 1- 1450 Dual Stick w/ power steering 1- 1200 in pieces 1- 1864 in pieces QA36A Thrower, #1 Tiller w/ extensions, IH windbreaker, IH wheel weights, 44C mower deck, 50C mower deck, CCC 54" Blade, GT46 high vacuum deck, GT54 deck, Cub Tripple Bagger, Custom dozer blade, Custom suitcase weights, 3pt cultivator, lawn sweeper, original R-Bucket |
Thread Tools | |
Display Modes | |
|
|
Cub Cadet is a premium line of outdoor power equipment, established in 1961 as part of International Harvester. During the 1960s, IH initiated an entirely new line of lawn and garden equipment aimed at the owners rural homes with large yards and private gardens. There were a wide variety of Cub Cadet branded and after-market attachments available; including mowers, blades, snow blowers, front loaders, plows, carts, etc. Cub Cadet advertising at that time harped on their thorough testing by "boys - acknowledged by many as the world's worst destructive force!". Cub Cadets became known for their dependability and rugged construction.
MTD Products, Inc. of Cleveland, Ohio purchased the Cub Cadet brand from International Harvester in 1981. Cub Cadet was held as a wholly owned subsidiary for many years following this acquisition, which allowed them to operate independently. Recently, MTD has taken a more aggressive role and integrated Cub Cadet into its other lines of power equipment.
This website and forum are not affiliated with or sponsored by MTD Products Inc, which owns the CUB CADET trademarks. It is not an official MTD Products Inc, website, and MTD Products Inc, is not responsible for any of its content. The official MTD Products Inc, website can be found at: http://www.mtdproducts.com. The information and opinions expressed on this website are the responsibility of the website's owner and/or it's members, and do not represent the opinions of MTD Products Inc. IH, INTERNATIONAL HARVESTER are registered trademark of CNH America LLC
All material, images, and graphics from this site are the property of www.onlycubcadets.net. Any unauthorized use, reproductions, or duplications are prohibited unless solely expressed in writing.
Cub Cadet, Cub, Cadet, IH, MTD, Parts, Tractors, Tractor, International Harvester, Lawn, Garden, Lawn Mower, Kohler, garden tractor equipment, lawn garden tractors, antique garden tractors, garden tractor, PTO, parts, online, Original, 70, 71, 72, 73, 76, SO76, 80, 81, 86, 100, 102, 104, 105, 106, 107, 108,109, 122, 123, 124, 125, 126, 127, 128, 129, 147, 149, 169, 182, 282, 382, 482, 580, 582, 582 Special, 680, 682, 782, 782D, 784, 800, 805, 882, 982, 984, 986, 1000, 1015, 1100, 1105, 1110, 1200, 1250, 1282, 1450, 1512, 1604, 1605, 1606, 1610, 1615, 1620, 1650, 1710, 1711, 1712, 1806, 1810, 1811, 1812, 1912, 1914.