|
PLEASE PATRONIZE OUR SPONSORS!
|
|||||||
 |
|
|
Thread Tools | Display Modes |
|
#1
11-01-2014, 12:53 PM
|
|||
|
|||
Shop Floor FIRE PROOFING....?????
I have a new 14' X 32' Building It is going to be a great work shop, but I need to figure out a way to make my plywood floor somewhat fire retardant. I don't want to have to weld or plasma cut outside in the winter. I have a great Fireproof paint for the Walls, but I just don't know what to do about the floor. I have RTV'd all the joining spots in the shop and it's prepared and nothing in it. I don't want to move in till I figure this out. I would prefer to leave the floor as it is and coat it with something.
|
|
#4
11-01-2014, 01:57 PM
|
||||
|
||||
|
What about garage floor 2 part epoxy paint. You might get a burn spot or two if you are plasma cutting or welding, but I think it would definitely seal it. Probably not advisable in a completely wood structure. You might consider putting drywall up on the walls also for fire stop. (good time to insulate for cold weather too) just my .02
Nice shop by the way too!!!
__________________
1966__122 Cub Cadet. Owner: Calvin, 6 yrs old Dad: Craig
|
|
#5
11-01-2014, 03:20 PM
|
||||
|
||||
|
My feeling about welding in THAT building????????
 You might as well spray gasoline before you start, it will go up in flames eventually. The issue is not the floor, it is the entire structure. A spark goes somewhere, smoldering starts, in the middle of the night, you hear the fire trucks driving up,,,,. Those welding/cutting sparks go 10 feet,,, land in some dust and/or cob webs, and the smoldering starts.  You could do a water washdown after welding EVERY time.
|
|
#6
11-01-2014, 03:27 PM
|
|||
|
|||
|
The entire building on the inside will be coated in a ASTM E-84 Class A rated paint. So I'm not worried about the walls ceiling ect. My problem is If i paint the floor I would have to re do it every couple of years.
I have seen this stuff work.
|
|
#7
11-01-2014, 04:03 PM
|
||||
|
||||
|
I like Sam's idea of sheet metal.
__________________
1966__122 Cub Cadet. Owner: Calvin, 6 yrs old Dad: Craig
|
|
#8
11-01-2014, 05:01 PM
|
|||
|
|||
|
Sheets of aluminum diamond plate like in trailers. But wet the floor first weld or spatter sparks will burn through sheet metal. But I would not weld in that building.
They used to inpregnant plywood years ago with salt and still might for fire retardant. But eventually every thing burns with enough heat. I always have a silver bullet (water can) handy when I weld or cut. In the winter I put anti freeze in it for freezing. You can buy them for like 5$ at flee markets. I have 5 or 6 around the garage and sheds.
|
|
#9
11-01-2014, 05:56 PM
|
||||
|
||||
|
I know its more money than you probably want to spend but if your going to weld in there I'd insulate, use sheet rock on walls and ceiling then pour a 1" floor of concrete. Then use your paint on the sheet rock. Once you get that building filled with your toys you don't want it burning. Plus you'll have a nice warm place to work.
__________________
1977 1650 with cast iron lower grill housing, cast iron oil pan, 54" push-snow blade, rear blade, disc-harrow, 44c and 48" decks, Two cultivators, #1 tiller with both extensions, loaded tires, 75' weights and chains, #2 cart.
|
|
#10
11-01-2014, 06:00 PM
|
||||
|
||||
|
And don't forget an exhaust fan...
__________________
1977 1650 with cast iron lower grill housing, cast iron oil pan, 54" push-snow blade, rear blade, disc-harrow, 44c and 48" decks, Two cultivators, #1 tiller with both extensions, loaded tires, 75' weights and chains, #2 cart.
|
|
|
|
Cub Cadet is a premium line of outdoor power equipment, established in 1961 as part of International Harvester. During the 1960s, IH initiated an entirely new line of lawn and garden equipment aimed at the owners rural homes with large yards and private gardens. There were a wide variety of Cub Cadet branded and after-market attachments available; including mowers, blades, snow blowers, front loaders, plows, carts, etc. Cub Cadet advertising at that time harped on their thorough testing by "boys - acknowledged by many as the world's worst destructive force!". Cub Cadets became known for their dependability and rugged construction.
MTD Products, Inc. of Cleveland, Ohio purchased the Cub Cadet brand from International Harvester in 1981. Cub Cadet was held as a wholly owned subsidiary for many years following this acquisition, which allowed them to operate independently. Recently, MTD has taken a more aggressive role and integrated Cub Cadet into its other lines of power equipment.
This website and forum are not affiliated with or sponsored by MTD Products Inc, which owns the CUB CADET trademarks. It is not an official MTD Products Inc, website, and MTD Products Inc, is not responsible for any of its content. The official MTD Products Inc, website can be found at: http://www.mtdproducts.com. The information and opinions expressed on this website are the responsibility of the website's owner and/or it's members, and do not represent the opinions of MTD Products Inc. IH, INTERNATIONAL HARVESTER are registered trademark of CNH America LLC
All material, images, and graphics from this site are the property of www.onlycubcadets.net. Any unauthorized use, reproductions, or duplications are prohibited unless solely expressed in writing.
Cub Cadet, Cub, Cadet, IH, MTD, Parts, Tractors, Tractor, International Harvester, Lawn, Garden, Lawn Mower, Kohler, garden tractor equipment, lawn garden tractors, antique garden tractors, garden tractor, PTO, parts, online, Original, 70, 71, 72, 73, 76, SO76, 80, 81, 86, 100, 102, 104, 105, 106, 107, 108,109, 122, 123, 124, 125, 126, 127, 128, 129, 147, 149, 169, 182, 282, 382, 482, 580, 582, 582 Special, 680, 682, 782, 782D, 784, 800, 805, 882, 982, 984, 986, 1000, 1015, 1100, 1105, 1110, 1200, 1250, 1282, 1450, 1512, 1604, 1605, 1606, 1610, 1615, 1620, 1650, 1710, 1711, 1712, 1806, 1810, 1811, 1812, 1912, 1914.
Linear Mode
