|
PLEASE PATRONIZE OUR SPONSORS!
|
|||||||
 |
|
|
Thread Tools | Display Modes |
|
#1
11-27-2016, 04:42 PM
|
|||
|
|||
Convert Snow Plow to Johnny Bucket
Hi has anyone attempted to convert (temporary) a snow plow made for the 1641 into a Johnny bucket? I have1641 that the existing snow plow and hooks up to the hydraulic lift, could enclosing the blade with sides and a bottom work like a Johnny plow? Any thoughts plan issues, or problems doing this? I would like to lift loose dirt and drop around the yard no real digging.
If this has been down before does anyone have pictures? 
|
|
#2
11-27-2016, 04:52 PM
|
||||
|
||||
|
I have a Johnny Bucket but do not see how you plan to tilt the bucket to dump it.
__________________
With my son, EricR Super 2084 with 54" mower, 451 blower. 2086 with 3 pt hitch, 54 inch deck, 551 blower, 54 in brinly blade. A 4 digit original w deck. A 70 with deck. 2 102s both with 42 in decks, one with creeper, 1 36 inch IH snow thrower CW36, 1 42 inch IH blade. 149 with mower. 2072 w 3 pt hitch, Johnny bucket, 60 in mower, 451 blower. Jacobson GT 10 with mower. DR Lawn vac tow behind,Home made lawn roller. Brinly cart, 2 off brand carts and 1 home made cart.
|
|
#3
11-27-2016, 04:55 PM
|
||||
|
||||
|
Quote:
__________________
(2) Original, 100, 102, 124, 73, 800, #1 and #2 cart, brinly plows, disk, IH184, IH244, 1948 F Cub
|
|
#4
11-27-2016, 07:10 PM
|
|||
|
|||
|
Jonny Bucket
I was hoping someone had already figures out the dump. I think I would have to modifity how the blade attaches to the mounting bracket. Any ideas?
|
|
#5
11-27-2016, 07:13 PM
|
|||
|
|||
|
Bucket
Do you have any detail pictures of the mounting and dump mech for the Johnny Bucket or a manual?
|
|
#6
11-28-2016, 01:51 PM
|
|||
|
|||
|
I've seen pictures someplace where someone added a bottom, sides and a cutting edge to a front blade.
They "pin hinged" it at the top (Like a dump truck tailgate) and it worked like a clamshell.
__________________
More IH Cub Cadet Parts RIGHT HERE
|
|
#7
11-28-2016, 08:18 PM
|
|||
|
|||
|
Quote:
If you want someone to figure it all out and tell you how to build one, I'd be happy to. Send me $1000 to start, and when I complete it you can pay any remaining balance. Otherwise get out your tape measure, torch and welder and build your own.  
|
|
#8
11-28-2016, 08:47 PM
|
|||
|
|||
|
I see that you "J-Mech" is a moderator for this forum. It is sad that this forum would allow someone with your type of attitude to be a moderator and a representative of this forum. Most forums are welcoming and helpful to new individuals that are new to collecting and working with metal etc. I believe you must be a very unhappy person if the only way for you to feel good about yourself is to try and put others down. Good luck with what seems to be a sad life. I will not be visiting this forum again.
|
|
#10
12-02-2016, 09:23 PM
|
|||
|
|||
|
You need to understand, it gets a little old with questions that have been answered time and time again. With a little research on here and on the intraweb 99% of the answers can be found. So dont be lazy and use some ingenuity, research, and hard work and build it. Then when you get stuck come back with an attempted project and ask some sensible questions.
Until then, J-Mech is right. JMHO 
|
|
|
|
Cub Cadet is a premium line of outdoor power equipment, established in 1961 as part of International Harvester. During the 1960s, IH initiated an entirely new line of lawn and garden equipment aimed at the owners rural homes with large yards and private gardens. There were a wide variety of Cub Cadet branded and after-market attachments available; including mowers, blades, snow blowers, front loaders, plows, carts, etc. Cub Cadet advertising at that time harped on their thorough testing by "boys - acknowledged by many as the world's worst destructive force!". Cub Cadets became known for their dependability and rugged construction.
MTD Products, Inc. of Cleveland, Ohio purchased the Cub Cadet brand from International Harvester in 1981. Cub Cadet was held as a wholly owned subsidiary for many years following this acquisition, which allowed them to operate independently. Recently, MTD has taken a more aggressive role and integrated Cub Cadet into its other lines of power equipment.
This website and forum are not affiliated with or sponsored by MTD Products Inc, which owns the CUB CADET trademarks. It is not an official MTD Products Inc, website, and MTD Products Inc, is not responsible for any of its content. The official MTD Products Inc, website can be found at: http://www.mtdproducts.com. The information and opinions expressed on this website are the responsibility of the website's owner and/or it's members, and do not represent the opinions of MTD Products Inc. IH, INTERNATIONAL HARVESTER are registered trademark of CNH America LLC
All material, images, and graphics from this site are the property of www.onlycubcadets.net. Any unauthorized use, reproductions, or duplications are prohibited unless solely expressed in writing.
Cub Cadet, Cub, Cadet, IH, MTD, Parts, Tractors, Tractor, International Harvester, Lawn, Garden, Lawn Mower, Kohler, garden tractor equipment, lawn garden tractors, antique garden tractors, garden tractor, PTO, parts, online, Original, 70, 71, 72, 73, 76, SO76, 80, 81, 86, 100, 102, 104, 105, 106, 107, 108,109, 122, 123, 124, 125, 126, 127, 128, 129, 147, 149, 169, 182, 282, 382, 482, 580, 582, 582 Special, 680, 682, 782, 782D, 784, 800, 805, 882, 982, 984, 986, 1000, 1015, 1100, 1105, 1110, 1200, 1250, 1282, 1450, 1512, 1604, 1605, 1606, 1610, 1615, 1620, 1650, 1710, 1711, 1712, 1806, 1810, 1811, 1812, 1912, 1914.
Linear Mode
